Somethings to add make sure to only run the ski 30-90 seconds because the carbon wear ring doesn’t get water when hose is hooked up and it will over heat. Also if you pull the oil pump tube out a little you can hold the throttle and hold the start button the ski will crank only and this will allow excess trapped oil in the passages to be flowed down to the bottom of the pan then tube pump again!

I got one of those last week, a similar pump failed after about 10 changes. Hopefully this one is more durable, but compared to dealer oil change prices ,you could buy a new pump for every oil change.

Forgot to manually crank the engine ( depress throttle and start button) doing this allows engine oil to flow into oil filter compartment. Do this until ALL all oil is out.

Next time you have the deck off and you need to run the engine for a long time try pointing a hose through the intake grate towards the front to get water down the shaft to the carbon seal. You can reach down and feel the steel flange that spins on the carbon seal and see how much cooler it is.

Good way to wreck your carbon seal. The manual says to never run it over 90 seconds even if it's on the hose, because the seal gets no cooling.

@larky368

Жыл бұрын

5 minutes! That thing must have been red hot. All you have to do is spray through the intake grate to get some water to the carbon seal.

@pdxwildchildroberts5586

Жыл бұрын

Yikes..Carbon seal..spendy fix..no need to run, eva..just turn it over, holding throttle down for count to 5-10 at start, and 2-3X during oil removal..should get 2-2.5 qts..and replace the star-nut O-ring on the Cap, also👍

Bob, very informative! Would be great to see the winterization & de-winterization procedures, or possibly have it explained to mechanic (similarly how you've done with stones damage on your sea doo).

@bobsudeyko4088

2 жыл бұрын

One thing. When warming up your Seadoo only run it for 1 to 1.5 minutes.

@richardnagrabski9301

10 ай бұрын

Informative? Wrong information all around. Using used oil to lubricate the new ORings was the icing on the cake for epic fail. This guy is a hack..

@rickmoohs9619

9 ай бұрын

​@@richardnagrabski9301Are you serious? Do you really think using a miniscule amount of used oil on a oring is going to affect anything 😂😂

I'm a Retired Professional Wrench, I use a Pneumatic Air Operated Fluid Evacuator that contains up to about 8 Liters of Fluid, easily transported with 1 hand and simply pour out the the Fluid into an appropriate Reclamation Tank. Note: Compressed Air required (Shop Compressor). Randy AKA randog311

I hope you took Nathan for a ride on the Seadoo. He worked hard for it. 😄

@bobsudeyko4088

2 жыл бұрын

J His mum won't let him go

@strobaholic

2 жыл бұрын

@@bobsudeyko4088 Well I guess you’ll just have to take her along with you. I’m sure she’s really cute lol.

Per Users Manual, you should not be running it more then 2 minutes - Drive line seal has no cooling when watercraft is out of water. Please correct me if I am wrong?

@Ipera78

3 жыл бұрын

That was the first thing that came to mine mind, 5min sounds like a lot,

Do oil changes after a ride. Already to a good temp for removal without stressing the carbon seal

I'm currently a Yamaha PWC owner. what is the supercharger maintenance look like on one of these. We are looking at adding a second unit

I’m going to have to that job twice in the not too distant future

Bob, really nice job. Own two of theses same 300 Limited skis and maybe now will attempt to do the next oil change myself!

@bobsudeyko4088

3 жыл бұрын

Fairly simple. Particularly after you have done it once. Just make sure at the end of it all that the dip stick measurement is right. Let it run for 3 to4 minutes to get an accurate reading. If to much suck a little out. At the dealership the cost is high but even more of an issue is that you might have to weight weeks without your machines.

@bobsudeyko4088

3 жыл бұрын

Wait

@szeldov

3 жыл бұрын

@@bobsudeyko4088 From my 2019 GTX manual: NOTICE Never run engine longer than 2 minutes. Drive line seal has no cooling when watercraft is out of water.

@aaron-fauth

3 жыл бұрын

You should be doing it yourself

Helpful thnx

Where you jetting this weekend Bob?

Great Video. Where did you get that funnel from?

Аймаладец!

Everyone needs a Nathan! Great video. Do you happen to have a link for the pump you used or the name maybe? Thank you!

@bobsudeyko4088

3 жыл бұрын

It’s stored away in the seadoo for the winter. I just searched on Amazon and found it there.

@NorthwestSawyer

3 жыл бұрын

Thanks for responding. I think I found it.

I got a kit and it comes with 2 oil filters and I can't find the place where the second one should be, if it exists. Any advise?

@bobsudeyko4088

2 жыл бұрын

The machine only uses one oil filter

Hey from Oz, I like your extra platform, did I miss the video on it? Which one is it and can you put two linQ items at once with the full seat on?

@bobsudeyko4088

3 жыл бұрын

facebook.com/BSDesigns4PWC Thats the link to the guys who make it in I think florida. It's expensive. Their price isn't to bad but then theres the exchange rate the shipping cost and if you luck out maybe a duty cost. For me the whole thing was almost 600 Cdn by the time I got it. Yes you can carry the top case the cooler and extra gas with the back seat on. I think it works pretty good and now I can bring everything with me if i want too. Tell the guys Yukon Bob referred you if you go for it.

@bflinders7275

3 жыл бұрын

Thanks Bob! I will look in to it. Thanks for your videos!@@bobsudeyko4088

Where you bought the pump?

Is that double LinQ platform aftermarket or did you make it ? PS- Nice video. We ride all the same places but never bumped into ya.

@bobsudeyko4088

3 жыл бұрын

It's aftermarket. You can find more about it here. facebook.com/BSDesigns4PWC It's kind of expensive for what it is. Not the companys fault. Mostly exchange and if you are unlucky at the border you may get hit with duty charges. Almost 600 Cdn for me. Built well and works well.

Maybe i missed it but should put it in drown mode and crank then Re suck the crank case

Run it for 4-5 minutes?

Well bob . Just wondering . Did it end up ever sinking ? Notice a lot of people were saying your carbon seal may be toast for running that long out of water !??

@bobsudeyko4088

3 жыл бұрын

No problem with the carbon seal. I probably only ran it for about three minutes. It is correct however that it really shouldn’t be run for much longer than that. I misspoke when I said 5 minutes.

@richardnagrabski9301

Жыл бұрын

You misspoke during the entire video. Stick to what you do best..

@azr2d1

10 ай бұрын

@@richardnagrabski9301 I agree. Let a pro (or backyard mechanic with at least a few oil changes under his belt) do the work. He also didn't change the small O ring. FAIL.

You warmed the Ski for 5-7 minutes, that is a no no in a SeaDoo. Then you used dirty oil to lubricate the O-rings, wow. Your next video should be how to replace the carbon ring.

Is there something electronically you have to reset in the computer after doing an oil change?

@bobsudeyko4088

3 жыл бұрын

If there is I don’t know. I just change approx every 50 hours

@hookdup1927

3 жыл бұрын

@@bobsudeyko4088 i looked into it. It seems A 400$ diagnostic tool called candoo professional is needed to reset the maintenance icon .

@azr2d1

10 ай бұрын

@@hookdup1927 I seem to recall seeing it mentioned in owners manual how to reset it......

Didn’t measure how much you put in? 😁

Does the oil filter container secure flush? I’ve tried several times and there is a small gap every time

@bobsudeyko4088

3 жыл бұрын

It should just spin on to a little beyond hand tight. There is a rubber seal that also needs to be in place where the filter meets the engine. I have not noticed a gap once it’s tightened a little beyond snug.

@jrdaviskid

3 жыл бұрын

@@bobsudeyko4088 thanks Bob. I still see a small gap. Is there a rubber seal other than the o rings?

@bobsudeyko4088

3 жыл бұрын

@@jrdaviskid no there is just the one rubber ring. It’s not really an o ring as it is flat. The old ring that is already on there needs to be removed. Sometimes the rubber seal that is on there will stick on the engine mount and will not come off with the filter. Only one ring at a time is used.

hey bob is there a bit of a gap between the top cap of the filter and the housing like can you see the o ring a bit ?

@TheReinoPaasonen

11 ай бұрын

There is and its normal.

@bobsudeyko4088

11 ай бұрын

Correct

@eddiea8167

2 ай бұрын

This was my concern. Thought I was doing something wrong and didn’t want to start it. Doing the oil change right now for the first time.

Hello Bob, just curios why did you heat up the oil before changing it?

@bobsudeyko4088

2 жыл бұрын

It just allows it to be more viscous and then makes it easier to drain more of it. Should not run the engine more than about two minutes.

@Maliken1992

2 жыл бұрын

@@bobsudeyko4088 thanks, I bough the same pump on amazon it works great.

@azr2d1

10 ай бұрын

@@bobsudeyko4088 Ideally you do this after a day at the lake. Drive it home and change the oil right away. It should be nice and warm still. Doing an oil change end of season (when it's colder) will suck, especially with the synth blend oil. Use full synth.

@bobsudeyko4088

10 ай бұрын

Just so that it change the viscosity a little and allow it to flow a little more easily.

Bob - how do you reset the "oil change required" message?

@bobsudeyko4088

3 жыл бұрын

Good question. I don’t know. I have never had it come on. Must be something in the manual. You must have to toggle through the menu and reset something in the settings. Sorry I cannot help anymore.

@szeldov

3 жыл бұрын

@@bobsudeyko4088 Maintenance Reset (only if maintenance is required) Using right arrow button, Select RES MAINT and hold OK button to reset maintenance. NOTE: The maintenance reset can only be done within the first 15 seconds of ECM wake-up.

Read your owners manual for oil Quantity/quality

How do you reset the light?

@bobsudeyko4088

3 жыл бұрын

I don’t. Just change the oil every 50 hours.

aweee your dog is so cute and howcome you never bring him with you on one of your trip

@bobsudeyko4088

3 жыл бұрын

Not my dog. Just baby sit once in awhile.

@andrewgarcia8589

3 жыл бұрын

@@bobsudeyko4088 ahh tru but proberly when its get older right and by the way bob you have a merry chrismas and a happy new year as well for your family and hop 2021 ill be a deffrient year

Are you using Synthetic Oil?

@bobsudeyko4088

3 жыл бұрын

Yes it’s a synthetic blend. Comes in a kit from the dealer along with the filter. About 85.00.

What is the name of the pump you used??? Where did you buy it??

@bobsudeyko4088

2 жыл бұрын

There is no name on it. I bought it from Amazon. Just google oil pumps and see what it give’s you

@brucearduser35

2 жыл бұрын

@@bobsudeyko4088 Thanks much for the video .... great job! I went to amazon and found the pump ... $20

@bobsudeyko4088

2 жыл бұрын

@@brucearduser35 one thing Bruce. Only run it for about 1.5 minutes to warm up the oil. I misspoke when I said d 5 min

great job .. keep it up

poor carbon seal..... never run over 2 min out of the water........ :/

5 to 7mins ,Not!!!..1 fried carbon seal, 60 seconds max..

How many quarts did yours take?

@bobsudeyko4088

Жыл бұрын

To far back now. I can’t remember.

@imathreat209

Жыл бұрын

@@bobsudeyko4088 thanks for the reply. I made the mistake by not measuring.

Five minutes?! Eeeeekkkmmm😂

It should have been more like 4.5 litres of oil and the carbon seal probably toast.

Run it that long out water i bet u just burned up ur carbon seal.

Bro you know it’s only 2 min right ? Poor carbon seal

Hey Bob i know this is an old video , would you have a link to this pump ?

@bobsudeyko4088

Жыл бұрын

No I don’t but I bought it through smazon

@alainbrouillette7740

Жыл бұрын

@@bobsudeyko4088 Thanks i will look into this .

Who agrees this guy is not very smart

A whole lot of bad information and omitted information. You should not be giving advice on you tube. Please stop.

Using old contaminated oil to lubricant the new o rings? Really!! How about cranking the engine to remove remainder of the old oil. Bad advice all around!