Great video. I just replaced my seal because your video taught me how to do it. God bless you, Sir!

@jonparkmac

3 жыл бұрын

Glad it helped .. ride on brother

Top video! And have to say, that’s a super clean engine bay 🤙🏻

@jonparkmac

2 жыл бұрын

Thanks man. Helps me find parts when I drop them .. and I do all the time lol .. I use purple power and let it slosh around on the trailer returning home

Subscribed! Great video - very detailed and informative. I just ran into an issue yesterday with my 96 GTX at the lake where I would rev super fast, but the exhaust pressure was the only thing moving me. A few searches and I made it here - hoping this will be the fix I need as it seems relatively straightforward. Definitely going to inspect the wear ring as well as these are new to me.

@jonparkmac

2 жыл бұрын

The carbon ring is only a seal. Your issue sounds like a wear ring. Search "Gray ghost seadoo pump" for my vidi on that

Great video. Well done and articulate. Some steps we missed. I personally don’t trust plastic zip ties for any length of time unless it’s manufactured recommended or not critical. Like a small engine fuel line to close for comfort. Lol 🔥🔥 School of hard knocks I guess. Live and learn.

@jonparkmac

4 ай бұрын

Thanks and glad you liked it. Zips are commonly used there but yes a SS ear/oetiker clamp is best and oem. A metal screw clamp is a mistake unless you use two and offset them 180 so they stay in balance.

Great video and thank you for taking the time to explain why it needs replacing

@jonparkmac

9 ай бұрын

Always happy to hear when my videos help someone

Great informative video, can't wait to get a 2000's GTI going to be my first ski, I work on all my own stuff so the 717 seems like a great engine

@jonparkmac

Жыл бұрын

It's the most reliable and plenty power for midclass ski. Make sure the oil lines are in good shape and oil in the tank and they'll last a while

The channelocks idea was brilliant. Thank you!

@jonparkmac

2 жыл бұрын

Yep. I cannot take credit for that. Mate on seadoo forum shared that gem

Awesome vid. Did this today. This made it easier. Thank you

@jonparkmac

2 жыл бұрын

Glad it helped brutha .. only reason I do these vids

exellent thank u so much now i feel ready to change my seal

Fantastic Video, Very informative Thanks for sharing

Excellent video!

Great explanation video.

Thank you!!

Great video

@jonparkmac

11 ай бұрын

Thanks man, hope this helped.

Great video and detailed explanation. I have a new to me Seadoo Challenger with single engine. Engine starts and runs great. My issue is the boat won't plane. I have replaced the wear ring and oil in pump. Impeller secured nicely and tightened pump to hull after a few in and outs in water. The outcome is boat still didn't plane. Can't seem to get past 10mph running really 7-8k rpms. Every now and then it'll plane and take off. Was told maybe a carbon ring issue. Would going through this rebuild process fix my issue?

@jonparkmac

2 жыл бұрын

If carbon seal is too lose it can suck air into the pump and dilute the jet stream

@marcbrazzers

5 ай бұрын

Check out the seal behind the pump, usually there is a foam gasket there

Great video - I have a 96 GTX and I rebuilt the carbs, replaced all fuel lines, new fuel selector, cleaned and rebuilt RAVE valves, but now I can only seem to get to about 3500/4000 RPMs and can't get above a very slow cruising speed (20km/h). My next step is to pull the pump, replace the wear ring and perform this service you show in your video. What are the odds this corrects my issue?

@jonparkmac

Жыл бұрын

If the motor doesn't rev past that, then it's not the wear ring or pump. If it does, the it's wear ring or cavitation ..or worst case stripped drive shaft splines. Try disconnecting the rectifier ..they sometimes interfere with ignition.

I am getting water into my hull, about 2-3" in 24 hours if the seadoo is just sitting in the water. I didn't think it was coming in from where the carbon seal meets the metal disc (support ring I think it is called). There is no water dripping where these 2 surfaces meet. It appears to be coming in at the thru hull. Is this common, and any suggestions on how to replace the thru hull? or am I missing something?? Thanks for the excellent video.

@jonparkmac

11 ай бұрын

They can leak around the thru hull fitting. There's a repair kit for it. I've not done this there, but if you clean it real good with acetone and apply thin layer of 3M 5200 it may stop it for a season or so. Check the back bolts where the shoe mounts to the stern. There's also bolts that come up from the grate. Those can leak

I'm finding this to very difficult, is there anything i need to know that would make this easier. I cant get the prop off of the back (the part with the prop) took all 4 bolts off and detached all the small hoses and still cant get the unit off to get to the drive shaft... help

@jonparkmac

2 жыл бұрын

Take all hoses off. Sometimes they are rtv glued on. Pour gas on to losen it. Tie it to tree and pull it off. Can also use a dent puller

Can carbon seal cause you to loose top end speed? Reason I’m asking my top end speed is 48 mph with 7200 rpms. I should be able to hit 55 to 60 mph with my seadoo gtx 155 but hard stop at 48 mph

@jonparkmac

Жыл бұрын

Yes it can if it's a weak seal. The pump can suck air thru the seal and cause cavitation. Other thing to check is a tight wear ring ..tolerance should be 1 mm or less for max performance

I have a 1994 sea doo xp jet ski, but it works a bit and then it turns on the heater alarm. what will be the problem

@jonparkmac

3 жыл бұрын

I could not say, but join the Seadoo Tech Support fb page and they'll help.

great video!

@jonparkmac

Жыл бұрын

Glad it helped

@oldsalt8011

Жыл бұрын

@@jonparkmac is the idle adjustment difficult to get too?

@jonparkmac

Жыл бұрын

@@oldsalt8011 no, just have to remove the air box. But you want 3000 out of water and 1500 in water. Don't tune or even run out of water. So if you are trying to lower the idle cuz it seems to high on trailer .. mistake. Also if you do change idle you then need to readjust the oil pump and line up those marks.

@oldsalt8011

Жыл бұрын

@@jonparkmac Thanks, I'll try to check for the dumb stuff like a leaking vacuum line and a stuck throttle. Yea, I have to be careful that I don't create more problems. I'll look for those marks on the oil pump just so that I can be wise to them. Thanks again for the reply.

Why did you use a zip tie on that boot? what about the metal clamp that was there? Is it supposed to go back on?

@jonparkmac

3 жыл бұрын

You mean the oetiker OEM clamps. Not good to reuse as they are usually damaged on removal. Use new ones if you have them, need clamp tool. in this case zip ties fine, and common.

@pekoprecision

3 жыл бұрын

@@jonparkmac OK got ya. I'll see if I can find some the right size. Othewise yeah I'll zip tie them

should that be done whether there are issues after so many hours?

@jonparkmac

Жыл бұрын

A new one will last a long time. Supposed to check every 100 hours. People burn them down running the ski out of water and shorten the life. Keep it wet and grease the pto zerk

Question....Does the engine oil need to be drained 1st? Thanks

@jonparkmac

2 жыл бұрын

No, there is no engine oil. There is injection oil and oil for the rotary gear. 2 strokes

@Peterlopata

2 жыл бұрын

@@jonparkmac oh didn't know this was a 2 stroke. I assumed it's 4 and that's what i was asking for. I need to do this repair and seen on another video that Sea Doo recommends removing the oil

Is the same process for 2007 gti 155 se?

@jonparkmac

Жыл бұрын

I think so yes. Check your manual to be sure.

Great video,where did i buy this kit from?

@jonparkmac

Жыл бұрын

Osdmarine

Do you have the link for the parts kit you ordered?

@jonparkmac

3 жыл бұрын

I ordered from Amazon, but OSD marine has oem ones. This is working good for me. www.amazon.com/dp/B0713RZRLC/ref=cm_sw_r_cp_apa_glt_fabc_25YCRMFFMV7X1CF7MJQY?_encoding=UTF8&psc=1

@kylewatts7796

3 жыл бұрын

​@@jonparkmac Are you still happy with that kit? I ordered the same but unfortunately carbon seal came in with a knick in it. Debating returning and buying a different kit, or just having it replaced.

How much should this cost at a dealer ( hours of labor?)

@jonparkmac

2 жыл бұрын

$50 for labor. Better to learn to work on these yourself or you'll turn a $1500 ski into a $4000 money pit

How long did this take an hour?

@jonparkmac

3 жыл бұрын

Yeah, bout an hour and lot less if you've done it before and have all your tools/parts handy.

Where did u buy the kit from?

@jonparkmac

Жыл бұрын

OSD marine

Why replace? When do you know when to change? TIA

@jonparkmac

2 жыл бұрын

Need to replace or ski will sink. Check by feeling the pressure with your hand .. should be little snug and not loose or too tight. Check hull often for water

I'm glad i have a Kawi,no carbon seals lol

were can i order the parts?

@jonparkmac

2 ай бұрын

OSD marine

Great video explaining it. I was wondering how or where the water stops before entering the hull and now I know it comes into the actual rubber bellows boot and stops where the carbon seal contacts the metal collar and also the two orings inside the metal collar. Pretty vulnerable setup! Those two cheap hose clamps on that eubber bellows are very important!😊

@jonparkmac

10 ай бұрын

It's quite reliable actually. That's why seadoo used it for many years. The other option is a sealed carrier bearing, which is also good ..but can tear out the thru-hull fitting if the bearing seizes. Those aren't cheap clamps, they're thicker stainless steel from factory

Good video but I wouldn't have used a cable tie to replace a metal clamp.

@jonparkmac

6 ай бұрын

I mostly use oetiker where it matters. In that spot zip tie is commonly used .. but yeah SS ear clamps always good. Just never use a metal worm drive clamp there

has a small water leak

Wouldn’t be nice if seadoo would utilise the same tech as Yamaha and Kawasaki and use a bearing instead of a carbon seal, Did you know? FACT; seadoo used to use a bearing and a stainless steel ware ring pre 1996 They quickly found out that the flaw with the motor is it only had three motor mounts, therefore highly increasing the risk of engine miss alignment causing the bearing to buckle and seize and the impeller would violently hit the stainless steel wear ring. At the time it would cost seadoo a lot of money to pay rotax to change their design, so instead they decided to make wearable items and charge the customer for the parts. Therefore seadoo makes money on the entire life of the jetski Food for thought Yet people keep buying these things You can’t make this up

@jonparkmac

10 ай бұрын

I've heard similar story. When the bearings seize they tear out the thru hull fitting. That's why some prefer the carbon anyway.

@AlexanderTheGrateful

10 ай бұрын

@@jonparkmac can you elaborate on this? Kawasaki and Yamaha use bearings and in the 25+ years I’ve been riding I’ve never heard of that happening to these brands, If this was happening to seadoos, then why would people keep buying them, So you are saying people prefer the carbon seal rather than having the issues with the engine mounts fixed and run a bearing like the other two manufacturers without any wear items? I highly doubt it...

@jonparkmac

10 ай бұрын

It's clear you are bent on bashing the Sea-Doo brand in general. Yes a ton of people buy them and enjoy them .. so you'll have to suck it up and move on

Grrr… you didn’t show the pulling back of the seal and getting C clip out…

@jonparkmac

3 жыл бұрын

Look at the end, I show you

@terryhites1

3 жыл бұрын

Yeah, I seen that, I wanted to see the part where the old one wouldn't come out and all the tools got thrown and the jetski got flipped 🤣

@jonparkmac

3 жыл бұрын

Lol .. that was me taking the exhaust off my 4tech.

What state is the Westside Marine business app I just tried to Google them there’s one in Arizona I just want to Texas so where did you get the parts at because I have two 1997’s and I never knew that you had to replace those

@jonparkmac

Жыл бұрын

Find me on Facebook and IM me. I'll take care of ya 💪💪

@expatconn7242

Жыл бұрын

I need to know what your Facebook picture looks like

@jonparkmac

Жыл бұрын

@@expatconn7242 facebook.com/jonathan.mcclure.9?mibextid=ZbWKwL

@jonparkmac

Жыл бұрын

Also OSD Marine is a very good source for parts .. and you should join the Seadoo 2-stroke tech support FB group as well ..a lot of help there

Quite a lot of your name on fb. What is your fb pic of ..

@jonparkmac

Жыл бұрын

Bees. Side hobby beekeeping that's dwindling. Now it's chainsaws 🤠