Ran into the identical problem with my mother's 32" Samsung. Both LED strips were bad on it. There were actually burn marks around the LED's that most likely initially dead shorted, before opening. The set only lasted 6 months. Since this was a black Friday purchase, the light strips were half the cost of the TV, so I purchased a new one for her and listed the individual boards on Ebay. The only inquiries that I have had for them were from people asking if I still had the LED backlights...............

Great bit of information in the comments... Thanks ....Leo

The main problem is no one is telling the costumer to keep the backlight settings low, just about all the ones I repair ( 5 a day now in the uk) are set at 100% , if they were at 75% they would last years longer. I set mine after repair at 45% and the picture is fine.

@12voltvids

7 жыл бұрын

This is no different than back in the CRT days.In that all important drive to have the brightest picture with the most contrast, manufactures made tubes with very dark glass to reduce reflections. Then they cranked the sh1t out of the tube to make it a table lamp not a TV, and people wondered why the picture tube was shot after 4 years, when their old set lasted 20+ years,

awesome bud. i have a samsung, backlights work, all voltages are coming out of power supply board. whats your thoughts on Tcon or video card bad? i have no sound either.

Thx a lot! It's very useful!

enjoyable, thank you ...

$40 for 5 new 10 LED strips for a Sharp 43" Roku TV. Mine had 4 of the 5 strips with 1 or 2 bad LED's I could power it up and see one strip flash and then go out. Each LED on the strip has a + - test point and in continuity mode you can see each one faintly glow if good. I tried to replace the bad ones and got them to all fire but the LED's were the wrong value and didn't glow bright at all. It worked but I had dark spots on the screen and then they too failed after about 30 minutes. I could not find the correct value LED's (maybe 6V 250ma? super bright!) so just bought 5 new strips and all is well. Be very careful with the LED panel when lifting off the diffusers, its pretty thin and fragile. Best is to lay it panel face down and lift the backlights off the supported panel. There were 3 layers of diffusion under the LCD. Fresnel, diffuser and opaque layer.

@oldguy8177able

2 жыл бұрын

yes that is how to fix.

Client must be crazy. Easyist repair ever. It's time consuming but if you have some spare LEDs it would only take an hour, then good as new. Shame he never let you finish it.

@12voltvids

7 жыл бұрын

I agree, but that wasn't my choice. I offered to fix it, but then I am going through a 3rd party. The guy that brought it to me is not the owner, he is the system integrator so I am dealing with an installer, giving him the diagnosis, and he is dealing with the owner. Installer called me and said throw it together and I will pick it up.

@TheUniversalEyes

4 жыл бұрын

Easy repair, easy to prevent also. Turning down the backlight strength to 50% will prevent over voltage. You also won't notice much of a difference in picture quality.

@68pishta68

3 жыл бұрын

@@12voltvids He used your diagnosis and is replacing the tube by himself.

My only issue with my Samsung LED tv UN55FH6030F is the backlight. when I increase the backlight to 12 and up the screen will get very dark and when it’s on 11 it is not bad but not presenting a good quality of image and it’s dim. Appreciate your advice if this could be the Capacitor problem or the LED light strips? Thanks

Never mind, a good bit of diagnostics, still enjoyable to see you have a go :-D. If the owner had not been so stupid, you would have had time to do more to the set. I see its as the owners loss, not giving a pro like you the time is just silly :-(. Hey i thought you were going to pause the video making while concentrating on your job, dont wear yourself out :-(.

Are all Samsung Led's have parts that are interchangeable?

Is backlight bleed fixable?

My tv turns on but is very dim no matter what I do to the settings, but you still can faintly see the picture. Do you think some of the led lights are out on the backlight or maybe a motherboard??

I've come across the same problem and the problem usually is the power supply. Symptoms are exactly the same: the 12V line is hovering somewhere near 9V and backlight is flickering. I suspect there is a problem with the PFC chip underneath the power supply since the voltage on the main reservoir capacitor is at 330V, not 390V, where it should be. Unfortunately I haven't been able to find the chip so I can't verify this, so I have just replaced the whole board.

@allenfleckney5969

7 жыл бұрын

I doubt that , 9 times out of 10 it's a failed backlight. If one shorts it can flicker , but just testing to see which backlights have failed and replacing them is easy.

@12voltvids

7 жыл бұрын

The power supply connector lists the voltage at 9 volts which is what it is delivering.

@12voltvids

7 жыл бұрын

Which is what I was prepared to do but the owner wanted it back to get a second opinion.

@frankscarano4708

7 жыл бұрын

12voltvids I went on Samsung support site and they offer zero zilch schematics... they focus most of the diagnostic on useless info about the main board port pin id's etc.. no real relevant service info.

@fotisp3

7 жыл бұрын

the power board is the L42SFV?

Thanks for the video, but being technologically challenged I need advice on how to get started. My 60" Samsung LED backlight went out, and a Geek Squad guy ordered a board for me. The board just got here today and I'm going to try to tackle this myself. I have just one basic question: If the TV is attached to a stand (sitting on a desk), is it necessary to take the stand off to remove the back panel? Once I get the back off I'm sure I can compare the new board to the old one to replace it. Thanks.

@12voltvids

7 жыл бұрын

Some TVs it is necessary to remove the stand, and others it can be removed with the stand on it.

@Grrr036

7 жыл бұрын

Thanks.

LED Driver on the main board or the power board will do it, most times it’s a capacitor or IC Circuit easy change

My Samsung TVs backlights won’t turn on if my power supply is screwed into the back of the tv like it’s suppose to. But as soon as I take it if or set something between the tv and the board, then my back lights turn on. What could cause this? Is it save if I put electrical tape on the metal part of the tv where the ground screws go?

So what happens when you have standby light, LEDs go on when you disconnect PS from Main board, but TV will not turn on LED's when you power up and plug PS into main board? This one got me....

Yeah its the led strips. I've repaired about 5 of this model now and every one of them had multiple LEDs burnt out. Can get a brand new set for 20 bucks on Ali Express, they come from China and take awhile to get here but they work good.

@peterpettigrew4410

4 жыл бұрын

Are they easy to fix? Mine went half dark (barely visible) and right side is normal.

Is good tutorial..thanks

Does Vizio's do the same with the power not coming on because of a bad LED? thanks for posting

@12voltvids

4 жыл бұрын

All led tvs will not display a picture if the backlight is out. Some you can do the flashlight test on.

It's not a backlight problem. Power supply drops the voltage.

If you're not going to give the engineer the time and resources to fix something you shouldn't waste their time in the first place. Your customer is a tool.

@12voltvids

7 жыл бұрын

I'm dealing with a system integrator that removed the set from the end customer and brought it to me. I would love it if he said keep it, because then I would find the LED that is out and fix it like I did that Philips LED that went south a few years ago. Same thing. A bunch of LEDs in series, so if one goes you loose the string, and the way these units are set up if you loose a string it upsets the current draw on the PSU and throws an over or under current fault that shits the set down.

@BenjaminEsposti

7 жыл бұрын

What they need is a zener diode in series with every LED ... that way, when an LED fails like that, it will still allow power to flow.

Ah yeah, LED backlight failures. I don't even worry about getting the LEDs to replace them with since they're harder to find, I just use a diode. If it's just a couple of LEDs out you can't really tell once it's back together because of the diffuser. I also tell people to turn their backlights down on their LED TVs a bit to lower the load on these circuits, it will extend their life. Often they are set to 100% at the factory.

@12voltvids

7 жыл бұрын

My new 4K set came with them set to 20 from the factory. I generally run them at about 12 (20 is full) and the picture looks great at that level.

@Sloxx701

7 жыл бұрын

Oh also, didn't know if you knew about these but a 500 pack of some backlight leds - www.aliexpress.com/item/500PCS-LG-LED-Backlight-1210-3528-2835-1W-100LM-Cool-white-LCD-Backlight-for-TV-TV/32685786152.html?ws_ab_test=searchweb0_0,searchweb201602_2_10056_10065_10055_10068_10067_10054_10069_10059_418_10073_10017_10070_10060_10061_10052_10062_10053_10050_10051,searchweb201603_7&btsid=9b56e2a0-3d2d-4d0e-8774-d410967da681 I might try ordering some eventually myself.

@drewbytheway

6 жыл бұрын

the LEDs are pretty easy to get and replace actually. shopjimmy sells packs of them all day long lol

Mine is flashing 6 times?

Question. My tv flickers with main board and led connected. When i unplug the led the flickering stops and i hear the samsung sound but no picture (ofcourse) any suggestions?

@12voltvids

5 жыл бұрын

Probably a bad led. They are about as reliable as an old Yugo or lada.

Darn sad, what a waste of material

yes.. samsung make good tv ..see all video 12volt repairing about samsung TV

@12voltvids

7 жыл бұрын

I like Samsung. I have many of them here. The problem with the LED backlights failing is more than likely people running them at 100% I keep my only LED set at 80%. Same for my Plasma sets. I keep them at 7 or 8. Never run them at max, too hard on components.

@allenfleckney5969

7 жыл бұрын

To be honest Samsung backlight failure is rare compared to Toshiba (Europe Vestel) and LG

@12voltvids

7 жыл бұрын

We used to call Toshiba "Toshitba" at work when I was working at the shop.

Hey. Good video. I’m having almost the same problem. I have a 75 inch tv. When everything is plug normal. It turn on off on off. It’s stays on for less then 3 second. If I unplug the main board. The led start freaking out just like that tv does in this video. BUT if I leave the main board plug and unplug one of the LED Plug (this one has 2 plugs).... the tv stays on and you can heard the volume if I press it up or down. Do you know if it’s one of the LED taking too much volts or its the main board?

@12voltvids

4 жыл бұрын

Probably the LED

@primeramusic3593

4 жыл бұрын

12voltvids okay. like I said. This tv has 2 plugs for the LED. How could I test it without having to take screen apart. I have a power supply

@12voltvids

4 жыл бұрын

@@primeramusic3593 Check the voltage drop across each plug

@primeramusic3593

4 жыл бұрын

12voltvids I open the tv. And got to the LED BAR. Theses are not across like the others tv. Theses one are in the side. Left and right. I believe it’s not the LED. Because (there are 4 LED). If I disconnect one of them the tv stays on. For example. RIGHT TOP AND LEFT TOP gotta be connect at the same time for both to work. RIGHT BOTTOM and LEFT BOTTOM gotta be connect at the same time for left and right bottom to stays on. But this is what is happening. If I disconnect one of the top LED , The Tv stays on but only left and right bottom working.,,, if I disconnect one of the bottom, the tv stays on but only left and right top LED works.

@primeramusic3593

4 жыл бұрын

I checked one of the plugs. And L3- voltage drops to 0 if the 4 led are connect.

I finally ran into a plasma panel failure. The dreaded Panasonic 1 blink code. Iam parting it out with tearful eyes. 58" of beauty.

@12voltvids

7 жыл бұрын

I have a 50" Samsung with a bad panel. Has a green line running down the screen. I gave it to my kids to play video games on. Still has a beautiful picture other than a thin green line that goes top to bottom. It is starting to burn , so eventually the phosphor will burn and it will be a black line.

@allenfleckney5969

7 жыл бұрын

I've just repaired a Panasonic 50 inch with the one blink code, it was the main board, are you sure it's the panel.

@int53185

7 жыл бұрын

Replaced the A board but no luck. That usually means a bad panel.

@frankscarano4708

7 жыл бұрын

James Last that's odd because a 1x blink points to an A board communication failure.. panel failures generally produce 7 blink codes due to error feedbacks to the su and sd boards trying to drive the panel.

@jl7775

7 жыл бұрын

James Last

my samsung ua40f6300 no backlight but with sound at audio output connected to my amplifier and i see image by flashlight,whats possible cause,led driver is in power supply board,

@12voltvids

7 жыл бұрын

There are a number of possible causes. It could be a single failed LED inside the panel. I have had a resistor on a set similar to this go open. It was a 10 ohm resistor in the PFC (power factor correction) circuit that sent up in value to about 250 ohms but that put the set into a shut down mode with 5 double blinks of the power light.

I fix the broken LED light and I test them every thing was good. After 1 hour using tv the back lights gots again dark . Where is come from this problem ?

@nilsfrahm1323

3 жыл бұрын

might be another led failing again. when one goes bad, voltage fluctuates and can stress others too hard, too. I saw this in Led bulbs, once one led fails, even if you repair it, others fail soon.

@nilsfrahm1323

3 жыл бұрын

the design is not good, many leds in series, this makes the weakest one get stressed by higher voltage. Once one fails, next one is stressed out. In li-ion batteries, they use balancers to evenly charge them, you can see an example in which they couldn't cheap out on parts, as it could explode. On leds, they don't care.

have you ever come across double imaging and ghosting on a Samsung it's a bout 5 years old I have tried putting tape on the ribbon but it still will come back model no 46D5000

@12voltvids

7 жыл бұрын

That sounds like a timing controller failure from the description.

@derekmcdonald9788

7 жыл бұрын

Any ideas on a fix .with some knowledge and doing at home thanks

@frankscarano4708

7 жыл бұрын

derek mcdonald double imaging especially jittering is always a panel failure, any horizontal lines or horizontal effects are always panel related due to tab bond failures in the panel. Tcon issues will generally be loss of video entirely, symmetrical vertical bars and similar. Any localized effects are always panel related because lvds data to tcon are in 8-10-12 bit data streams and will effect the image globally when you get failures outside of the panel... thin vertical and horizontal localized lines... shadowing, ghosting and horizontal jittering is always panel related

@derekmcdonald9788

7 жыл бұрын

Frank Scarano any ideas were to source 1 a panel or what do i need to ask for living in Ireland ty

@frankscarano4708

7 жыл бұрын

Honestly panels are the most expensive part in the tv and is generally not cost effective to repair. they tend to cost equal to if not more than the cost of replacing the set

Please I need power supply voltage label

Troubleshooting my first free-to-me-dead-LED-TV. Samsung UN48j5000. PSB is L48MSF_FDY BN44-00852A, LED strips are: 2015 SVS48 FCOM FHD DOE A RIGHT REV1.2 150605 LM41-00120Q_LM4100149A. No joy with SM or schematic search. I pulled the back off. Saw no bulged caps, black R's, nor burn marks on any of the three boards. At first plug in, I heard BZZT...BZZT....BZZT about once/sec. I was looking at the back-of-the-set when this occurred. Sounded like the noise was coming from behind the Main board. I also detected a faint whiff of electricity/ozone/something getting hot. Sounded like arcing. With power to backlight connector removed, I was able to verify V's to Main board as OK. Stripped it further down so I could view the backlight strips. Found bad burn mark on strip 2 up from bottom, on far right hand side, between second-to-last & last LED. Burn area nearly full 'height' of tall trace (8mm) and about 13mm side-to-side!! WTH? All 32 LEDs (4 strips x 8 LED's/strip) stil worked when tested with bench supply. Attempted to repair burned area but no joy. I may just cut the end off & complete the series strip ckt with solder, then see of the PS will power up, stabilize and light the remaining 31 LEDs. If not, arcing may have damaged something in backlight driver ckt on backside of PSB. I've done a close visual inspection. Didn't notice anything. Out of all the videos I've watched, only seen one with a burn mark on a strip. Why in the world would arcing begin between two LEDs? Very odd failure. Perhaps at this place in the series diode string the voltage must have been high enough to arc to the metal backing of the strip? After some PSB tracing I discovered that though there are four pairs of backlight wires (+-1, +-2, +-3, +-4), there is only a single series ckt AND a single backlight driver. Not two or more like some larger sets. 3V x 32 LEDs = 96V. I wonder if the BL driver ckt raised the driving V to its MAX attempting to bridge the growing burn area which looked like an open to it? Interested in your thoughts!

@canismajor3104

6 жыл бұрын

I finally figured it out. The strip I repaired drew way too much current. Must have been very damaged. Another LED on another strip began to sizzle so I immediately pulled the plug. Found local shop selling two right-hand-strips. Installed these and now all four strips (32 LEDs total) lit up fine and bright! Voltage & current draw for backlight ckt and drivers is back to normal. Learned a lot fixing this one. Second issue has to do with a few vertical stripes on the screen. I enjoy your videos! BTW, you helped me disassemble an old Sony Hi-8 camcorder and fix it. Ditto for an old mid-80's JVC HiFi VCR deck I still use on a regular basis! Much thanks for lighting the way!

Ok quick test on samsung tv's you can do and this is from samsung GSPN fast track manuals so it is proven... All samsung sets from the C series up will self power on the PS when you disconnect the main from the PS by removing the cable between them. When plugging in the set at this state the backlights should come on immediately and stay lit at full brightness and the power supply voltages should come on. If you dont get backlights or backlights are erratic you can eliminate the main from the equation. I saw in the video the BL was pulsating when you disconnected the main it was still pulsating.. knew immediately it wasnt a main issue and it had BL failure.. its been non stop with so many LED sets today its not funny!

@12voltvids

7 жыл бұрын

Yes I know the main board was fine from this test. I am still working on this set trying to find the problem, as all the LEDs test good. I took a battery and was able to light every stupid light on strip glows, and they all test OK, but they don't light when connected to the power supply board. Driving me mad, as I took the screen apart expecting to find a dead LED, but nope they all test OK. Any ideas?

@frankscarano4708

7 жыл бұрын

12voltvids the high speed switching diodes are known to short on these boards. The larger black ones in the backlight drive area. Check them. Since the leds are good then it's obviously somewhere on the ps.

@12voltvids

7 жыл бұрын

Yes that is what I am thinking. I took that screen apart expecting to find a bad LED, but every bloody one of them tested good. I know the main board was fine, as it ended up in an identical set with a bad main board, so now this set it mine to play with, and I suspect a bad diode in the psu. I just haven't got around to checking them all out yet.I would like to see if I can get it going just for fun because now it has a bad main board that reboots when the volume is changed but for a display where the volume is never changed it would probably work just fine, and I have a use for it as a digital picture frame if I can get the backlight problem solved.

@frankscarano4708

7 жыл бұрын

Let me know if i can help with any of these sets.. I have full access to Samsung GSPN for bulletins on all their sets..

@12voltvids

7 жыл бұрын

A schematic for the power supply would be great.I did check the power diodes, they are NUR460p and none of them test as short, but I am thinking that they may be going leaky under load? What do you think, replace all of them and see if that makes any difference?

I had the exact same TV, and the bottom half LED strip died. I could still watch TV but the bottom half would be darker than the top half. That was the last time I bought an edge-lit TV, and a Samsung TV. It only lasted about 5 years, which was a huge disappointment.

@12voltvids

3 жыл бұрын

I have a couple of Samsung sets that have been good. My plasma sets get heavy use and they have all been great.

@W31rdG

3 жыл бұрын

​@@12voltvids My Panasonic plasma was good and my folks have been using a Samsung plasma (720p) for 10 plus years without issue... there was some pretty bad retention at one point, but it's gone now. I think edge-lit makes me nervous more than anything.

Hey my tv light works when I unbluged the whole coord to the bord

@joshpotts6667

4 жыл бұрын

Denver Lipp same hir

Took entire tv apart and tested each LED strip. ALL GOOD. Replaced PS board and same result. TV starts up, i see LEDs come on and then go out. Flashing red 2 times and then it tries to start up again and again.... When I disconnect either one of the ribbon cables going from main board to panel the backlights stay on but when I connect both, the less go out. This one has me stumped.. Owner says they were watching tv and it just went out.... Let's see who can solve this one..

Everything works on my Samsung tv but the picture. Is it Junk? It’s only 3 years old

@12voltvids

4 жыл бұрын

More than likely a single bad LED.

I fix a lot of the LG back light I just by pass the led and the TV will light up only part hard taking out the lcd screen.

@allenfleckney5969

7 жыл бұрын

If you bypass the backlight you are adding extra voltage to the others meaning they will burn out quicker. Any 3v led from any TVs will work, it doesn't have to be the same strip

@leonjohnsonjr3331

7 жыл бұрын

I been doing it for 3 years no returns yet

@12voltvids

7 жыл бұрын

Correct, this will stress others, but at least it gets more life out of the set. If this set ever gets given to me I will be researching further, but the owner said he wants it back, so it went back together.

@allenfleckney5969

7 жыл бұрын

It may be ok to by pass one 3.5v led even though I don't advise it, but yesterday I did an LG 49 inch that had 12 faulty LEDs , so you can't by pass 40 volts they have to be replaced. These LEDs were advertised as having 10.000 hours. Lucky if they see 1000.

@12voltvids

7 жыл бұрын

I doubt that many of the LEDs that are advertised as having 20,000 live spans will last beyond 1 - 2000 hours. I am changing more LEDs at my house than the old compact fluorescents that did last 10 years. I have CFLs that are 12 years old and still going strong, but the LEDs seem to only last 2-3 years, and those ones were really expensive too.

My lg LEDTv is turning on , showing LG logo and then backlight dissapears . Its the strips, isnt it?

@allenfleckney5969

7 жыл бұрын

Most definitely the strips or to be honest. One or 2 failed LEDs on the strip.

@allenfleckney5969

7 жыл бұрын

If you are in the UK I may be able to help with spares

@12voltvids

7 жыл бұрын

I am still hopeful that the unit will be abandoned and then I can proceed with ripping the panel apart and checking out the lights. I have some strips from a broken screen set. The unit is sitting in my garage awaiting pickup

@Sivim

7 жыл бұрын

Thanks

@philmarsh9589

5 жыл бұрын

@@allenfleckney5969 Hi I came across your reply to a video and wondered if you could help with backlight leds for Samsung le46c750r2k ? Or possibly repair it for me ???

I have a Samsung UN39FH5000FXZA screen went black with blinking lights. When I disconnect the led plug from the power board I get sound?? Would that be the T-Con board??

@12voltvids

6 жыл бұрын

Rudy Castro Did you do the flashlight test.

@rudyjoe129

6 жыл бұрын

12voltvids I’ll have to try that again when I connect the hdmi. I’ll try it with that connected to power board and not connect to it

I am relatively surprised that they run that 195vdc on an LED backlight

@hellhound-si5oz

7 жыл бұрын

Says that's almost as high as an LED lightbulb runs the voltage up to

@capriracer351

7 жыл бұрын

These are all in series, so the individual voltage drops are quite low. Depending upon how many in the string, about 3 volts.

@allenfleckney5969

7 жыл бұрын

Well a 50 inch screen has 60 LEDs at 3.5 volts each in series so that's about right.

@12voltvids

7 жыл бұрын

The reason for the high voltage is the LEDS are in series. This allows low current. If the LEDs were in parallel the voltage would be low, but the current high, and this would require a laager transformer, and heavier wiring. Of course the down side of series LEDs is if one goes bad, you loose the entire strip.

Hard to jusify spending !,000 dollars on something that only lasts 3 years!

@12voltvids

7 жыл бұрын

I hear you. Nothing lasts these days. I would really like an OLED set, but it is hard to justify that kind of money on unproven technology. I still like my old Plasma sets they have proven to be reliable for me. I picked up a 4K set for the studio, and got the cheapest one of half decent quality I could find. Only 420.00 so if that only last a few years I won't feel so bad.

@int53185

7 жыл бұрын

12voltvids Was that a Sceptre brand? I've read some good reviews about them.

@TortureBot

7 жыл бұрын

I feel the same way about "unproven technology". When SSD's came out for computers, a tech for a local hospital I know was raving about how they bring new life into old computers because of their speed. I simply felt they were TOO NEW to fully trust with valuable data. So I have waited a few years to make that leap. Guess I am ABOUT ready, lol!

@nilsfrahm1323

3 жыл бұрын

@@TortureBot you're right. when ssd fails, data impossible to retrieve, as it is aplit over multiple chips. From Hdds you may still recover something. For surface errors, you can skip the area and still get most of files back. Had a WD hdd with bad sectors, I even partitioned it such that empty space was covering the bad areas and could continue using it for non-important backups, i.e. backups of another backup drive.

al tv samsung LED is short life not like the sony LED long life

@ryans413

7 жыл бұрын

Samsung makes good TVs but if you cheap out then you get what you pay for Sony Samsung are pretty good tv companies. At the moment I have a higher end Vizio witch is not bad but I have more Samsung TVs and haven't had any problems

@allenfleckney5969

7 жыл бұрын

Depends on the screen used not all Samsung TVs use Samsung screens.

@frankscarano4708

7 жыл бұрын

Allen Fleckney I hate to tell you that Sony has its fair share of panel failures where as it has less backlight failures it has plenty of tab bond and internal tcon failures.. and those damn android b,c, and d series Xbr sets have been a nightmare!

@allenfleckney5969

7 жыл бұрын

Yes they have but not as many as we see of the others. We see 10 a day with backlights issue , but only one a month Sony

@frankscarano4708

7 жыл бұрын

yeah.. BL failures arent Sony's weakness. its their main boards.. they are very probematic! Even the D series XBR sets are crapping out left and right! Even the DPS boards are crapping out on those XBR sets

BHOLANATH

SAMSUNG=TRASH

@markfrost2707

11 ай бұрын

theyre the best made

samsung sucks