Sailboat Refit #29 - Rolling, Sanding and Buffing Marine Paint to a glass smooth finish.
Sailboat Refit #29 - In this video, I finish Rolling on the Alexseal paint, sand and buff it out to a glass smooth finish.
Жүктеу.....
Пікірлер: 26
@alstovalljr2 жыл бұрын
Great, practical advice, once again. This channel continues to be one that offers DIY advice based on hands-on experience. Bravo!!
@finditfixitsailit9322
2 жыл бұрын
Thank you sir.
@Ken-fw7ue4 ай бұрын
Nice boat
@sergiorodriguez67212 жыл бұрын
Good job 👏
@RachaelSA2 жыл бұрын
That paint is looking shiny :D
@finditfixitsailit9322
2 жыл бұрын
Thank you!
@raytheron2 жыл бұрын
Yay! Your video made my day. What a finish you got there! Excellent job, indeed.
@finditfixitsailit9322
2 жыл бұрын
Right on! Thank you
@kaxazen50322 жыл бұрын
Glad to hear the weather is allowing you to get back onto this project. I look forward to seeing you finish the interior, rigging and get her back on the water.
@finditfixitsailit9322
2 жыл бұрын
Thank you. I’m ready to get this one done as well.
@jameymathis74522 жыл бұрын
Awesome job !!!
@finditfixitsailit9322
2 жыл бұрын
Thank you sir.
@billyisenhour26002 жыл бұрын
Thanks and God bless
@finditfixitsailit9322
2 жыл бұрын
Thanks for watching.
@genecarlsonii31152 жыл бұрын
Looks great John....got to say it....how about them Hogs.....
@finditfixitsailit9322
2 жыл бұрын
WPS!
@KiwiWebb2 ай бұрын
What was the time frame adding your 6 layers of topcoat? Any sanding between them?
@patrickcoe2934 Жыл бұрын
Are you recommending one build up primer coat -- sand with 300 or 400 grit - apply 2 or 3 coats of topside paint? From there, should I wet sand in 600-800-1000, etc.. grits to a gloss finish or should I sand with 320 grit and apply one additional top coat like you did on the first side and then wet sand? Thanks - great videos and level of detail is excellent.
@TheRickpfarr2 жыл бұрын
Captain John: What roller would you prefer using Alexseal?
@finditfixitsailit9322
2 жыл бұрын
I was using a mole hair roller here and it just doesn’t roll out as smooth. I like to use a 3/16 nap from Sherwin Williams. Not sure the info on the roller. When I fine one I’ll show it to you.
@billlambert2092 Жыл бұрын
Questions for you, please. 1. About how many sanding discs (in the finer grits) did you use for that length hull? 2. At what grit do you begin wet sanding? 3. What do you use for the guide coat? I have the the Mirka dry coat, do you prefer spray? Thank you very much. Everything you post is extremely informative.
@finditfixitsailit9322
Жыл бұрын
Hello, I probably used around 7 discs each after painting I started with 800 then 1200, 1500, 2000, and sometimes 3000. Depends on how smoothly your painting rolls out. After the first 800 sanding the rest goes quickly. I prefer spray guide coat, it’s easier the put on.
@finditfixitsailit9322
Жыл бұрын
The guide coat I got from o’Reilly’s auto parts, it’s cheap.
@billlambert2092
Жыл бұрын
I really appreciate the rapid response. I believe you are helping a lot of DIYers. Do you wet sand the 800?
@finditfixitsailit9322
Жыл бұрын
I do wet sand the 800 just be sure to use guide coat and don’t sand through the paint. You can touch up the paint if you do but it’s more work
@finditfixitsailit9322
Жыл бұрын
You might try 800, then 1200 Or maybe to 1500 on a area then buff it to see if it’s necessary to sand with high grit.
Пікірлер: 26
Great, practical advice, once again. This channel continues to be one that offers DIY advice based on hands-on experience. Bravo!!
@finditfixitsailit9322
2 жыл бұрын
Thank you sir.
Nice boat
Good job 👏
That paint is looking shiny :D
@finditfixitsailit9322
2 жыл бұрын
Thank you!
Yay! Your video made my day. What a finish you got there! Excellent job, indeed.
@finditfixitsailit9322
2 жыл бұрын
Right on! Thank you
Glad to hear the weather is allowing you to get back onto this project. I look forward to seeing you finish the interior, rigging and get her back on the water.
@finditfixitsailit9322
2 жыл бұрын
Thank you. I’m ready to get this one done as well.
Awesome job !!!
@finditfixitsailit9322
2 жыл бұрын
Thank you sir.
Thanks and God bless
@finditfixitsailit9322
2 жыл бұрын
Thanks for watching.
Looks great John....got to say it....how about them Hogs.....
@finditfixitsailit9322
2 жыл бұрын
WPS!
What was the time frame adding your 6 layers of topcoat? Any sanding between them?
Are you recommending one build up primer coat -- sand with 300 or 400 grit - apply 2 or 3 coats of topside paint? From there, should I wet sand in 600-800-1000, etc.. grits to a gloss finish or should I sand with 320 grit and apply one additional top coat like you did on the first side and then wet sand? Thanks - great videos and level of detail is excellent.
Captain John: What roller would you prefer using Alexseal?
@finditfixitsailit9322
2 жыл бұрын
I was using a mole hair roller here and it just doesn’t roll out as smooth. I like to use a 3/16 nap from Sherwin Williams. Not sure the info on the roller. When I fine one I’ll show it to you.
Questions for you, please. 1. About how many sanding discs (in the finer grits) did you use for that length hull? 2. At what grit do you begin wet sanding? 3. What do you use for the guide coat? I have the the Mirka dry coat, do you prefer spray? Thank you very much. Everything you post is extremely informative.
@finditfixitsailit9322
Жыл бұрын
Hello, I probably used around 7 discs each after painting I started with 800 then 1200, 1500, 2000, and sometimes 3000. Depends on how smoothly your painting rolls out. After the first 800 sanding the rest goes quickly. I prefer spray guide coat, it’s easier the put on.
@finditfixitsailit9322
Жыл бұрын
The guide coat I got from o’Reilly’s auto parts, it’s cheap.
@billlambert2092
Жыл бұрын
I really appreciate the rapid response. I believe you are helping a lot of DIYers. Do you wet sand the 800?
@finditfixitsailit9322
Жыл бұрын
I do wet sand the 800 just be sure to use guide coat and don’t sand through the paint. You can touch up the paint if you do but it’s more work
@finditfixitsailit9322
Жыл бұрын
You might try 800, then 1200 Or maybe to 1500 on a area then buff it to see if it’s necessary to sand with high grit.