Video like this are always really useful

@vectornetwork

Жыл бұрын

Thanks for your comment 🙏 Thank you for the encouragement! To improve, I've added thermal testing to all the recent videos. I'm also adding decibel readings (for fan noise) and full teardowns of the shroud (removing the fans, etc). I hope you stay tuned!

@JohnnyShikari

Жыл бұрын

@@vectornetwork so thanks for these other test! Do you have any suggestions on how to undervolt that card?

@vectornetwork

Жыл бұрын

@@JohnnyShikari Wow, great question and on point. I am capturing all the footage as we speak for the next video (4090 Founders thermals & teardown) and plan to address undervolting. Once I test undervolting on the 4090 (and showing it), I'll have a better understanding may be able to address your question better. Hope that helps

@JohnnyShikari

Жыл бұрын

@@vectornetwork Honest and "on point" answer. I'll wait that video! :)

@twentyjeans4234

4 ай бұрын

​@@vectornetwork Is the process same for 4000 super cards?

Like & subscribe for more content!

I just bought a used 3090 with the same cooler and it runs very hot with 100% fans. I am thinking of sending it to warranty service somewhere in the EU. If they will not do anything with it, will try repasting everything and then undervolt a little. I just hope it will not melt inside my case (Corsair 4000x w/ 6 Corsair fans).

@vectornetwork

Жыл бұрын

I've not tried the 3090 version of this card. For 3090s, the memory on the backside can get very hot if that is being used heavily during load. 3080s, all the memory is on the front. It really shouldn't melt inside that case if its setup with decent airflow. If there is a lot of visual dust and debris on the cooler shroud, then popping it open, repasting & new thermal pads (get new ones in advance, dont rely on reusing the old ones) may make a solid difference, especially if you can clean the cooler shroud at the same time. Best, Vector

I have a 80 degrees celsius after 10 minutes of Furmark, though i have a 12GB version

@vectornetwork

Жыл бұрын

Right on, I would be comfortable with those temps. 🙌

@federicofirlif863

Жыл бұрын

did you lower the temperature?

does this have the same pcb as the UPRISING XLR8?

Good to know that its a reference pcb. I have one of these just begging to be watercooled in a o11 Dynamic. Idk if its worth it thou...

@vectornetwork

Жыл бұрын

Right on, the PNY 3080 is an absolute champ of a card. The stock cooler performance was solid, so it would depend on your sound tolerance. I had two of those cards at one time in different builds and they both performed at or above my expectations. So much so that I am considering PNY for the 4090, since it will also be a reference PCB and it appears Alphacool may have a waterblock for it near launch.

@3milio0o95

Жыл бұрын

@@vectornetwork Considering the price of the 4000-series, I think I will be stuck with my 3080 for a while. But I'm looking forward to see watercooled 4090 with a OC core clocks of 3000+ mhz 🤤

@vectornetwork

Жыл бұрын

@@3milio0o95 Awesome, the plan is a PNY 4090 in an Alphacool Eisblock with two 360 Heatkiller rads and Optimus cpu block and reservoir combo 🙌

@vectornetwork

Жыл бұрын

@@3milio0o95 Thank you for your comment 🙏 The 4090 is now in a water block and should go into a custom loop this week, let's see how high we can crank it!

I just bought this card and it runs a bit hot and noisy for my taste, 82c max and it's very cold in my city, can't imagine how it would run in summer.

Thank you... i need the 1R0 2038 Power Inductor and this clear video helped me identify what is missing off of my PCB... if anyone knows where to get one, that would be great... its that gray box to the top right at EXACTLY 1:59 thanks.

@vectornetwork

Жыл бұрын

Thank you for your comment 🙏 I may not have your answer but I hope you find it

Great video! Was planning to do this on mine as well, did you notice any thermal improvements after replacing the thermal paste compared to the stock paste?

@vectornetwork

Жыл бұрын

Awesome man, I actually didn't notice any significant thermal improvements (it was already running at temps better than I expected with the stock cooler). I think it's a well-made card and the cooler is smaller and more compact than average, yet performs well.

@carloleal30

Жыл бұрын

@@vectornetwork Great to know, you saved me some time I guess, was planning to repaste everything in my pc but you confirmed it for me. Thank you!

@vectornetwork

Жыл бұрын

@@carloleal30 Sounds good boss, but if you find yourself wanting to repaste it, don't let me stop you. Can be good maintenance all around. ✊

Hello! Very interested in getting this card just for gaming. What were your stock VRM/Memory temps before opening it? Really curious to know. More power to ya!

@vectornetwork

Жыл бұрын

Thanks for your comment 🙏 I am putting together a testing rig and developing a repeatable testing methodology as we speak, so I can better provide that information. So, I regret not having that data available, but I will do my best to provide that in the future. For what's it's worth, I found the card to run slightly better than expected on temps/noise. The 3080 doesn't have any memory on the backside, so the memory temps were perfectly fine. Hope that helps.

Only 4k views and 45 likes? WTF? Your video is truly amazing.

@vectornetwork

Жыл бұрын

Thank you for your comment 🙏 Wow, thank you for the encouragement. I sincerely hope you find some of my more recent videos as I have made improvements over time. Thank you for watching.

Do you happen to know where the card's RGB header is? Or how to physically disable RGB?

@vectornetwork

Жыл бұрын

Thanks for your question. 🙏 I do not know for sure. There is one covered by the cooler and two one the side. Not aware of physically disabling the RGB, but maybe pulling out the white one on the side will do the trick. It may be possible to control the RGB with your motherboard's software. Hope that helps

Its OEM is Palit though, not PNY.

@vectornetwork

Жыл бұрын

Thanks for your comment 🙏 I am always interested if I made an error, so I can prevent that from happening in the future. So, help me understand what you mean by the OEM being Palit and not PNY.

@cuma666

Жыл бұрын

@@vectornetwork PNY 3090, 3080, 3070, 3060 cards are made by Palit, they only differ by fan shroud or simple sticker change, same goes for Gainward aswell.

i have same card not full rgb work what the reason

is the temp good for the stock cooling? im planning to get one but the brand is new so i dont want to waste money.

@vectornetwork

Жыл бұрын

Thanks for your comment 🙏 I am almost done with a test rig that will be able to provide that information for future videos. I don't have any test data for the PNY 3080, but from experience, the stock was perfectly fine and in line with other manufacturers. Hope that helps.

Hello! for this model, are you able to deshroud to remove the fans side without having to unscrew the backplate and exposing the chip?

@vectornetwork

Жыл бұрын

Thanks for your comment 🙏 I am looking at the cooler and there are screws all around the fan side. It appears that the fans can be accessed without unscrewing the backplate, but I haven't tried. In future videos, I plan on including a full teardown, including down to the fans. Hope that helps.

@blackmagexiv

Жыл бұрын

@@vectornetwork Hey there! I would love to see a full teardown on the 3080 xlr8, as I'm going to be deshrouding soon but I was only able to remove the metal outside of the shroud. Thanks!

what temps are you getting in full load?

@vectornetwork

Жыл бұрын

Thanks for your comment 🙏This card the PNY 3080 is currently in a Heatkiller water block that I'm thinking of putting into a SSUPD Meshilicious. When it was in its stock cooler, the GPU temps were fine, something normal and the memory temps were pretty cold, more than I expected--perhaps because there is only 10GB of it on this board. (I don't recall exact temps) If you are curious about the temps in my most recent watercooled soft tubing build on this channel, running a stress test in 3DMark like Time Spy or Port Royal, I'm getting somewhere low 80s for the GPU memory and GPU core something like 70s, maybe 80 max (a bit more than the ambient temp in the low 70s). The fans are running at approx. 1200 rpm. This is with the Heatkiller rads 360-L with 3x Phanteks T30s and 240-S with 2x Noctua A12x25. The temps stay fairly constant even under further load and the fans just pick speed to compensate. Hope that helps and thanks for asking 🙏

Really helpfull vid. Awesome work. Im planning to get one, is it good? pny is not the best brand, but some of the oldest card maker by nvidia. I'll apreciate if you give me some informations, thx

@vectornetwork

Жыл бұрын

Thanks for your comment 🙏 The PNY RTX 3080 is a suitable option. PNY is a long standing business (IIRC 30 or so years) located in NJ, USA. My understanding is that the produce cards for NVIDIA's Quadro line. They don't appear to spend that much on consumer marketing, so it is understandable that consumers aren't that familiar with the brand. From my experience, the cards are usually reference design (save on costs of customizing) and the cooler is typically no frills but certainly capable of the job (likely leveraging their experience with the Quadro line). My understanding is also that their warranty is comparable to other companies. Hope that helps.

Hola! Muchas gracias por tu trabajo, me podrías decir las medidas de los thermalpads de las vram ? Me sería de mucha ayuda. Muchas gracias

Can a 0.5mm or 1mm screwdriver do the job on the backplate

hello friend you will know the measurements of the thermal pads of the reference heatsink

@vectornetwork

Жыл бұрын

Thank you for your comment 🙏In future videos, I will make sure to have information on the thermal pads. For this one, I don't have the stock thermal pads for the cooler anymore so I cannot verify. Thank you for asking.

can liquid metal be used in this card?

1:03 did you just rip off white connector?

@vectornetwork

5 ай бұрын

Thanks for your comment 🙏 I checked the video and IIRC, yes, I just did rip it out. I tilted it side to side to get it out. I don't remember there being a clip. It pushes in like a fan header. Hope that helps.

@Epetrovdrums

4 ай бұрын

@@vectornetwork didn't know that, thx. I managed repaste it without pulling out that connector.

I almost bought this card but I was looking at the 3080 12gb and the Ti version. It was still $1100 at the time but I had a 30% "cash back" (store credit) for OfficeMax which would have generated $330 store credit after purchase. I ultimately decided against it as it would have still required the $1100 out of pocket and just in time, the other card I was looking at went on sale on Newegg for $729. The Gigabyte Gaming OC 3080 12gb. Far better value!

@vectornetwork

Жыл бұрын

Oh yea, for sure, better value. Congrats on the purchase! 🙌 The Gigabyte 3080 12GB is a beast and you got it for pretty much the MSRP of the 10GB FE at launch $699. Well done.

give me termal pad and others please this card

my video card is heated by hotspot up to 104

@vectornetwork

7 ай бұрын

Thanks for your comment 🙏 104 is kind of high but too high. Any other information? Air cooled? Stock or opened before? How long have you had it?

@user-qg6xx2wt2i

7 ай бұрын

@@vectornetwork My video card is 17 months old.I changed the thermal paste a couple of days ago, now the GPU Hotspot has a maximum of 85 and the gpu temperature is 76.The video memory is 86 degrees.

@user-qg6xx2wt2i

7 ай бұрын

Надеюсь понятно написал,я из России

@vectornetwork

7 ай бұрын

@@user-qg6xx2wt2i Well, there you go. Looks like it just needed a bit of maintenance. It's good practice and it gets easier each time you do it. Those temps look good, enjoy your card.