short video on how to wire up an ecu on rover v8 using the 14 cux ecu
Жүктеу.....
Пікірлер: 11
@seankenny54124 ай бұрын
Terry, excellent Video, can you tell me what is the 3rd posative off the coil going to?? Does the red/white give posative too the ignition or does it feed a posative from ignition
@nigelsnudden78535 ай бұрын
rover V8 wiring loom install
@derekcarroll787 ай бұрын
Hi running same system engine wont rev past 3000 over half throttle it cuts out . Any advice welcome
@ianwalkden30246 ай бұрын
I have the 3.5efi do you know if the wiring will be the same
@tenerifesonia4 жыл бұрын
Great video. I’m Using a 4.6 gem engine. Is it all the same?
@ALIasa9122 жыл бұрын
4:15 is 20A is good fuse for the ECU??
@deanmallett93364 жыл бұрын
Will this by pass my immobiliser
@terry9187
4 жыл бұрын
hi guys so this wiring loom is not the same for the 4.6 witch are in the p38s i believe that the immobiliser on the 3.9s are connected threw a separate relay that interrupts the signal from the coil feed to the ecu
@vicrammohamed8222
3 жыл бұрын
I just do wiring but the injector not firing when cracking I see the spark
@dominikdolbeau3108
2 жыл бұрын
Thanx so much for your video. There is only 2 vids about 14cux wirring explication. Specialy for 3.9l as mine. But I have trouble with it, because the color of wires are not the same. So, I have a question about the big brown wire. Is it a permanent 12v going to the ECU ? From the battery? When your car is in the garage, there is always 12 V run inside ?
@nigelsnudden7853
5 ай бұрын
This is the 4 cu "flapper" system - 14 cux is the later version, followed by gems Thor engine.@@dominikdolbeau3108
Пікірлер: 11
Terry, excellent Video, can you tell me what is the 3rd posative off the coil going to?? Does the red/white give posative too the ignition or does it feed a posative from ignition
rover V8 wiring loom install
Hi running same system engine wont rev past 3000 over half throttle it cuts out . Any advice welcome
I have the 3.5efi do you know if the wiring will be the same
Great video. I’m Using a 4.6 gem engine. Is it all the same?
4:15 is 20A is good fuse for the ECU??
Will this by pass my immobiliser
@terry9187
4 жыл бұрын
hi guys so this wiring loom is not the same for the 4.6 witch are in the p38s i believe that the immobiliser on the 3.9s are connected threw a separate relay that interrupts the signal from the coil feed to the ecu
@vicrammohamed8222
3 жыл бұрын
I just do wiring but the injector not firing when cracking I see the spark
@dominikdolbeau3108
2 жыл бұрын
Thanx so much for your video. There is only 2 vids about 14cux wirring explication. Specialy for 3.9l as mine. But I have trouble with it, because the color of wires are not the same. So, I have a question about the big brown wire. Is it a permanent 12v going to the ECU ? From the battery? When your car is in the garage, there is always 12 V run inside ?
@nigelsnudden7853
5 ай бұрын
This is the 4 cu "flapper" system - 14 cux is the later version, followed by gems Thor engine.@@dominikdolbeau3108