Route Internal Brake Hydro Line in Seconds!
In this video we show you how to route a rear brake hydraulic brake line without taking anything apart. BB stays in.
Check us out at www.bbinfinite.com
For fast service and quickest responses contact us via Facebook or Instagram messenger, or email at info@bbinfinite.com.
#shimano #cervelo #bicycles #campagnolo #sramaxs
Пікірлер: 34
Super helpful, have been nervous about pulling hydraulic lines so this is great
@BBInfinite
10 ай бұрын
It's good to be nervous, it makes you cautious. And it makes us all search for How-To's on KZread. Glad you liked the vid.
Pretty slick! Thanks for the boost of confidence!
Super helpful more video please
i have been looking for this all week thank you
Fast, clear and clever. Subbed
Thanks, you saved me a lot of pain.
Thank you bro for the trick 😊😊 I was not having a powerful magnet but I did it with a Bluetooth Speaker magnet😂😂 And now it is fixed🎉🎉🎉
@BBInfinite
11 ай бұрын
Bluetooth speaker magnet? Dang, MacGyver.
Glad you showed it with the bb and cranks on - I am a little afraid to take my BB off, might have bunged the install 😅
@BBInfinite
8 ай бұрын
We always subscribe to the "If it's not broken, don't take it apart...leave it alone" philosophy.
@dayinnymtb
8 ай бұрын
@@BBInfinite exactly my thought, I may have bunged my threads on the BB but it is on and works. I don’t want to deal with that until I need to. So I’m “leaving it alone” 😂
Well done 👏👏
Good vid, thanks 👍
Hi Boss ✌️👌👍Thanks for a Video, Best Jose (Chicago)
@BBInfinite
Жыл бұрын
Thanks for watching! Jose is a super fan.
I really like your stainless steel toolboxes/benches/cabinets. Do you mind sharing what brand they are? Thanks!
@BBInfinite
Ай бұрын
Thank you. The boxes and cabinets are all Seville Classics www.sevilleclassics.com/
A lot of times the housing or hose will get scratched up pretty bad from the sharp burrs and edges inside the frame. It’s unavoidable even if you lube the crap out of the housing/hose. Internal routed frames need to have conduit sleeves so the housing or hose goes in and out smoothly.
A great method to avoid cable-tying to the outside of the fra- aaaand I'm done.
Hey bbinfinte do you have a release date for the pulley wheel for the shimano 8170 di2 12 speed ultegra
@BBInfinite
Жыл бұрын
It will be soon. Sorry for the wait. We ended up testing a lot more than we anticipated.
Does this work if I leave the barn in the barb in the house? Or will I need a new barb?
@BBInfinite
7 ай бұрын
This works with the barb in place. No line cutting needed. It works with old lines too, since often they need to be pulled to replace rear suspension bits on full suspension mtb's, etc...
I don’t think my bike has stalagmites…but now I’m not sure.
@BBInfinite
Жыл бұрын
You'd be surprised. Funny that a lot of time it's the more expensive, custom frames that are the messiest inside.
This is avery good ad for Parktool IR 1.2 or 1.3
@BBInfinite
8 ай бұрын
How, when the "tools" used here cost under $8 total.
@NonLegitNation2
2 ай бұрын
his method cost alot less, but even if you do want to go with an actual kit why spend $75.00 on a Park Tool kit. I bought a generic kit for 17 bucks and it has all of the exact same fittings as the park tool kit. But instead of having a routing cable for each fitting mine has one routing cable and the fitting screws onto it. So less parts to worry about.
what if the original hydro line had Housing Damping Foam on it?
@BBInfinite
3 ай бұрын
Take it off if it won't fit.
kzread.infoEWt1trKlbLM kzread.info/dash/bejne/pJ2Dl7qSlLWYc5c.html We place cardiac stents like this. So what I would do is when you dismount calliper and leaver, put a wire in the old tubing (while still on the bike); than remove the tubing, keeping the wire inside the frame; than place new tubing back over the wire that is already inside. remove the wire.
Now do it with a banjo end.
@BBInfinite
Жыл бұрын
It works with a banjo. Obviously there's no way to fish a banjo end though a frame, but the same technique works with a banjo fitting. The cable will feed into the banjo inlet, and when the cable's die end meets the banjo it will often fit inside it if you tweak the die end 90 degrees. Done it many times for Hope and other brakes that use banjos.