Best explanation of the Trommel build. Didn’t know about needing to use duct tape, and how you got around that problem with sheet metal. Also smart thinking of bolts on the castor to make adjustments to them.

A very good video, sir! I might have to see about building one of these. Our garden seems to be mostly rocks with a bit of soil in it. This looked much easier to build and maintain than what I had in mind. Thanks for sharing!

Thanks for the video! Definitely a thumbs up. Going to see how to do this in series so I can get soil, but also to save out gravel and reject larger rocks.

Good video, full of ideas to enhance any basic trommel! Thanks.

This is a very helpful video! Thank you for sharing your knowledge- it’s making my life SO much easier😊

Liked it! Built one myself last May 2020. I put wheels at output end and handles at input end. the angle is 5 degrees for your slant. I liked the tin strips you use for each end and mid. to protect the rollers. the legs were adjustable for height at all 4 corners ( for uneven terrain). Had to buy three pulleys, two belts, lots of tie Wraps online. Lined center rim with Duck tape to level off between tie wraps for better traction. now I get to use it on the other side of house. By! Stay healthy!

Good design. I'm inspired to make one. Thanks

Well done Cody

Great video

Nice Job Sir!

Thank You Thank You Thank You Thank You, so much!!!!

great video

I built mine out of 1.5" x 1.5" , and added triangular corner braces top and bottom on the long sides. The bars holding the wheels are connected with bolts, washers and wing nuts so I can disassemble for storage. It all sits on saw horses. The motor and pulleys are on a board moveable laterally because of potential belt stretch; I use clamps to hold it in place. I have 23" rims; if I was to do that over I would get the wider rims from mountain bike tires as the rims I have are rather narrow; I had to get my knife out and trim the wheels to get them into the channel of the rim. So far I have not had problems with the dirt (clay) interfering with either the belt or the wheels.

@AgCWby90CS

3 жыл бұрын

My pulley and motor are adjustable as well. Each wheel is adjustable also. I’m about to dismantle for storage as I don’t have room to keep in operational form.

@timmoore6055

3 жыл бұрын

@@AgCWby90CS Both of us will have a gem of a sifter for compost. I am digging up my front yard, and clay does not break up; but if you smack it with the shovel first, it sifts just fine. Thanks for your video!

Nice vid!

@AgCWby90CS

Жыл бұрын

thanks.

Thank You! These are useful machines, and I know Bicycle Rims, are frequently used, but, I wondered if Motorcycle Rims would be an Option, for a More Durable Design? Plus,I wondered if anyone builds these in Longer Lengths, with Different Mesh sizes, like 1/4" at entrance, then 1/2" on second portion, with a strip of A Solid Area, like your Flashing, to allow a Divider to keep the two output grades, separated?

@AgCWby90CS

3 жыл бұрын

Motorcycle rims would require different track wheels and belt and maybe motor? There are longer ones on KZread. Search Trommel. Probably need a baffle underneath to keep grades separate, but I like that idea.

@guillermodehollander

Жыл бұрын

I love the idea of variable mesh from one end to the other.

@flatsville9343

Жыл бұрын

The longer trommels with 3 grades of screens are for vermicompost or fine sifting finished compost. The can be very expensive...like $1,000+

@racebiketuner

3 ай бұрын

Motorcycle rims are super strong compared to bicycle rims. IMO better to use aluminum than chrome plated steel, which will eventually chip, rust and flake. 18" and 21" diameter are the most common sizes. 21" x 1.85" wide (inside of flanges) is easy to find as it's used on the front of most dirt bikes. Rear rims are typically much wider.

Very nice. Would like to know the rpm of the motor

@AgCWby90CS

Ай бұрын

I didn’t even think about listing the specs on the motor. It has an RPM of 1725/1140 1/4 hp 60 Hz 115 V 5.2/3.0 Amps

Please explain wheel speed control by pulley main motor to drum speed control

@AgCWby90CS

2 жыл бұрын

This clip explains it better than I can. kzread.info/dash/bejne/nplhsM-gYNSfmqg.html

@sansarsingh2716

2 жыл бұрын

Pulley size

@AgCWby90CS

2 жыл бұрын

@@sansarsingh2716 The larger pulley is roughly 10 inches in diameter and the smaller pulley is roughly 3 inches in diameter. These measurements are from outside of flange to outside so where the belt sits in would be a little less and those would be roughly 9 1/4 inches and 2 1/4 inches.

@robertweekley5926

Жыл бұрын

Sansar - You want the speed "Fast Enough" have the Material ride up some, but not so fast, it stay "Stuck" all the way around (like as if, it was a Centrifuge)! That might change, as well, depending on Diameter, and if Material is Wet, or Dry. Test, to suit your needs!

@JordanArseno

2 ай бұрын

Converting from Motor Speed to Drum Speed is simple pulley math using the pulley diameters. Observe the video you'll see four pulleys. Each has a different diameter: Motor (M), Large (L), Small (S), Drum (D). The formula is simply: Drum RPM = Motor RPM * (M/L) * (S/D). The Motor RPM is 1725, so to gear-down the drum to a more manageable speed, make M & S small, and L and D large. D is already large (the bike rim), and is usually fixed in a project like this. You can play w the other values M, L, and S to get what you want. I reckon here: M=2, L=12, S=2, D=21 So: Drum RPM = 1725*(2/12)*(2/21) = approximately 30 RPM, which, isn't far off, watching the video.

What is that gear that you used from Tractor Supply? Can you supply the link please?

@AgCWby90CS

Жыл бұрын

I believe what you’re asking for is this. Chicago Die Casting 10 in. OD x 3/4 in. Bore Zinc Die-Cast Pulley for A Belts www.tractorsupply.com/tsc/product/zinc-die-cast-pulley-10-in-od-3-4-in-bore-for-a-belt

Dam. I was just thinking about building one. I use a old barrel Ring with 1/4 Screen across the ring. And I shake it. To sift. A good work out. Very smart man you are. Thanks.

@AgCWby90CS

Жыл бұрын

Yes, I had a wooden one and got tired of shaking. 😀

Speed reduce pulley calculation pl

i swear i saw this video in like 2015

@AgCWby90CS

2 жыл бұрын

Nope, didn’t have this then. But there are plenty similar clips out there.

Freaking Yankee Ingenuity. Sweet.

@AgCWby90CS

Жыл бұрын

Yankee??? Come south my friend.