THAT VIDEO WAS A LOT OF BROTHER, BROTHER! Figured out my spring for the smaller diaphragm wasn't strong enough that was included in the kit. Also the jet in the diaphragm. THANKS AGAIN BROTHER FOR HELPING US DUM DUMS.

I am astonished and delighted that a video of this caliber exists about a topic so specific to my needs. Really a great vid, James! I don't always luck out in that regard. I have an '06 1700 which I assume is pretty much the same, or enough so that I'm not going to get lost now that I have seen this. I especially loved the attention to detail, the asides about "watch out for the spring so it doesn't shoot across the room" and the warning about the orientation to replace the nozzle so it aligns with the inner pin. This is pure gold that, if one doesn't know about ahead of time, can result in an otherwise "simple" equipment dismantling ending up with a piece of useless garbage for the recycling bin, if the advice is not heeded. Thanks so much for this. I was glued. It's time to get out in my garage and start wrenching.

Get yourself some JIS screwdrivers as the screws are not true Phillips but JIS Japanese Industrial Standard. Great Tutorial James.

Excellent video! Thank you so much for posting this. Brilliantly done!.

Thanks for the video I could almost swear this was Kevin Costner lol this was very detail I I enjoy this video very much thank you😊

Best video I've seen yet. I have to do that thing to my buddies Roadstar

👍I have a 2003 with 98k miles and never been in shop for anything but 3rd gear recall at 5k along with change the jets in carb. I'd ride it from fla to alaska right now without a worry. Best bike I've ever owned. I'm ready to rebuild my carb so thank you for this vid...just what I'm looking for. Think I'm going to put a ported manifold on also. Thank again!

@darrenmitchell1792

Жыл бұрын

How many o rings are in your rebuild kit mine had 4 . The small one I could not find a place for it. ?

@Snowmonkeypablo

Жыл бұрын

was your recall on that trans fixed at no cost to you thru Yamaha ?? and were do I look my Bike Up ?? Thanks,,and agreed GREAT Video !

Holy shiznit, an unselfish member of the Roadie community LOL! THANKS James! Sub'd

Thank you! Big help when I needed to pull the bowl without removing the carb. Couldn't figure out what was holding the bowl after the four screws were removed! Running great now!

Great Step by Step: Thanks for the Video I just changed my main jet and went through the whole Carb. no problems bike runs great.

I'm going to be doing this soon, so I really appreciate this video. Thanks brotha!

@Jadams1911

8 жыл бұрын

You're welcome. I'm glad I could help out.

Fantastic! I wish I had Thought to search this about a week ago! lol You showed so many things I had questions to being a carb noob. This should get my 04 1700 Midnight Silverado going! I see the mistakes I made now. Great video!

Great video sir! Thank you!

Just picked up my 06 roadstar fantastic videos love the bike learning it do all my own work. Going to put lots of miles on this rig thanks for your videos I subscribed!!!

@Jadams1911

7 жыл бұрын

Thank you! I'm glad you liked the video. You've got a great bike! Mine is an 06 as well.

Great vid. Very helpful

thanks for making the video. helped me a lot to be able to clean my carb.

@Jadams1911

7 жыл бұрын

Thanks for watching, I'm glad I could help.

James thank you, I just bought a 2006. It had set for almost 2 years and my drive home the coaster enricher cover and spring blew off. Arizona heat and plastic just don't work well.

@Jadams1911

6 жыл бұрын

Those plastic covers dry out and get brittle over time. You can find replacement part here. www.yamahapartsmonster.com/oemparts/a/yam/50045703f8700209bc793276/carburetor

Big help thanks for making the video!

Great video!

Great video James! I’m just about to clean and rejet my Road Stars carby, I’ll be watching your every step when I do👍🏼. Just wondering if you would know the size of the float bowl replacement Allen head bolts that you recommend?

Fantástico video .. muchas gracias

best video I have found and believe me I HAVE been looking trying to get my back on the road were in belongs

@Jadams1911

7 жыл бұрын

Thank you! I'm glad you enjoyed the video.

Great video James used it recently to work on my roadies carb.any thoughts on how to set float height?I can't find any info on float specs only to use clear tubing to check fuel level.perhaps this topic would be an interesting video?

great job!

GOOD VIDEO !!!! good filming angle ***** five stars

@Jadams1911

8 жыл бұрын

Thank you!

Good stuff. Can you discuss adjustments to the TPS...if possible.? Thank you

Perfect video!!!!!!!!!! Thks

Hi, I have a o3 1600 Silverado that makes a chirping sound on deceleration or when you shift down, do you have a suggestion for the source of the chirping sound???

Good job

Hey man, why do you like the Road Star? I like it because it's similar to the Road King in style, but a much better value. Just curious why you like this bike over harleys.

Hi James, Great video!, I have one question, on my 2004 road star 1600 carb, how many turns out is the accelerator duration adjustment screw from the factory?, Thx! ;o)

Thanks for the info

Great video. I have a question. The 2 air jets. I take it those go back in tight?

@Jadams1911

2 жыл бұрын

Yes just snug the air jets but don't get them too tight because they are brass and will strip out.

Thank you for the great help with my roadstar carburetor do you know of anywhere where I can get a used carburetor for my roadstar because the one I've got I'm not sure it's going to work once I put back on

@Jadams1911

Жыл бұрын

Try a Facebook group.

I have a 2001 and a 2007. On both bikes the plastic collar at the handle end of the choke cable has broken. My question is are the choke cables the same on the 1600s and 1700s? I have not take the bike apart to look at the entire length of the cable. It appears the same on the handle and wear the collar is broken, but I cannot see where it enters the carburetor to see if the two cables are the same. If I find a couple of choke cables from 1600s, will I be able to use one of them on my 1700? And vice versa???

@Jadams1911

6 жыл бұрын

Yes the choke cables are the same on both models.

Good morning I was wondering if you could help me Figure out a problem I've had reoccurring problem even after I've rebuilt the carburetor of flooding the bike runs fine and then it percolate After I run it a while it pour gas out I have to let it cool for almost an hour 1/2 before I can try to Start it again or it'll continue to perculate And pour more gas out I really don't know what direction to take I was wondering if you could Point me In the right direction it a 2005 Yamaha roadstar Silverado 1656cc It really is a headache because I don't have confidence in the bike it's left me on the side of the road several times until it wants to run

@Jadams1911

2 жыл бұрын

You need to replace the needle set. It's allowing gas to bypass the float needle causing carb puke. I've had the same thing happen to me.

MY Pilot Mixture Screw seems to be blanked-off with a brass disc with a tiny hole in the centre of it. At 8:57 your video shows you unscrewing the PMS. Where your screwdriver tip is mine has this brass disc. I'm tempted to just leave it alone, or is there a way to remove the disc to get to whatever might be underneath it? Any help appreciated. cheers and thanks for the great video.

@Jadams1911

4 ай бұрын

The factory installs a brass plug over the PMS screw. You will need to drill a small hole not very deep just so you can insert a screw into the plug to pull it out.

Buenas cuantas vieltas yeba el tornillo del aire deuna yamaha roadstar 1600 año 2000 grasais espero me piesa ayudar

My fuel pump primes only when hoses aren't connected as soon as I hook them up fuel pump wont prime. Any help is appreciated.

@Jadams1911

2 жыл бұрын

First you need to attach a hose to the carb bowl drain tube and drain the carb, Retighten the drain screw and turn your key on and check to see if the fuel pump fills the carb. If it doesn't then check the screen that is inside the fuel tube , It could be plugged.

Hi I got a Yamaha Road Star Silverado Edition I watched your video on how to rebuild the carburetor it was very helpful but after rebuilding it it would not stay running I could pull the choke out and it would run but once I put it back in it did not it acted like it was running out it ran out of gas I can work the throttle real quick and keep it running that way but once I stopped doing that it stopped running can you give me any pointers on where to look or how to solve this problem

@Jadams1911

6 жыл бұрын

Well first off, did you remove the carburetor manifold from the heads? It sounds like you have an air leak somewhere. also make sure the manifold tube is blocked off or it will cause the bike to need the choke on to run at idle.

@rockynymia

6 жыл бұрын

James Adams I have same problem where is manifold tube

@EbaleyTheRogue

5 жыл бұрын

Interesting, Frank. The reason I stumbled onto James' great vid is because I have the same issue. I too wonder where the manifold tube is. On a side note, I wonder why a tube would be made that is required to be blocked off. I'm more a computer guy than a weekend mechanic, but I dig diving in to figure this stuff out. I just don't have a lot of background to know what the heck I'm doing. Did you discover where the tube was, and did somehow blocking it solve your problem?

Yes sir I would like to know where the o rings go . Just rebuilt a 2000. Had the smallest o ring left over. No top end power. Going to try adjust air jet and fuel jet. I’m trying…..Idle is good.

@Jadams1911

Жыл бұрын

There are two small o-rings One is on the PMS and the other goes between the carb where the accelerator pump is.

@darrenmitchell1792

Жыл бұрын

@@Jadams1911 the kit I had had 4 o rings. It seems to have low top end power too. Thanks (all balls)

I hear a lot of people talking about you have to changed you carburetor jet when you do need exhaust pipe,how do I know what size jet do I need instead us guessing of a other people say?

I just got a 1600 2003 and it came with a k an n intake and it seemes to pop out of the air cleaner some times have you ever run into this ? also it seems to have a squeek when i let off the throddle on decaleration

@Jadams1911

7 жыл бұрын

Im not sure what type of K&N filter you're referring too. If it's one that goes inside the stock air box it should be bolting in. if it's a K&N Filter that clamps to the carb, you'll need to design a bracket for it so you can bolt it to the bike. The squeak you're hearing could be a few things. Your belt is either too tight or too loose, order yourself a belt tensioning gauge www.ebay.com/itm/like/151476696652?lpid=82&chn=ps&ul_noapp=true Also make sure the belt is tracking in the center of the rear pulley. Jack up the rear of the bike and spin the rear wheel to check, use the adjusters to center the belt.

At 9:51 you are removing an air jet that is solid. When I removed each of my jets, I put them in a bag. I did not have any solid jets. I had been riding to work with no issues. Went about a year of not riding. Tried to start bike one day and it would only turn over. I figured since it had been sitting I needed to clean the carb. Cleaned and replaced what jets came with the kit I had, but it's still just turning over. If i place my hand over the intake it will start up and burn off whatever gas it sucks in and then dies. I'm stuck.

@Jadams1911

4 жыл бұрын

Placing your hand over the intake reduces the amount of air so it only needs a small amount of fuel to run. You have a fuel issue. You need to clean the entire fuel system since the bike sat so long. I would start at the tank. Drain all old fuel and make sure the petcock filter is clean. Replace with fresh fuel. Now before you attach the fuel line to the carb run a long hose from the fuel pump into a container and turn the key and run fresh fuel through the fuel pump to clean out any old fuel. Reattach the fuel line to the carb and start the bike. If you have cleaned the carb properly the bike should run.

@MrDunnyglenn

4 жыл бұрын

@@Jadams1911 I should have put all that information on there too. The tank has been cleaned. Filters on the petcock replaced. Currently I have a container with a hose connected to the carb with fuel running to it. I'm going to buy another jet kit and redo the carb. I know for a fact I didn't take off any jets that were solid. Carbs are my nemesis. I'm good with the electrical systems. Thanks for the reply sir.

Do you know if the Road star 1700 carburetor is same as the one on the video?

@Jadams1911

6 жыл бұрын

The carbs on the 1600 and 1700 are the same. The only difference is the jet sizes.

@ramphis71

6 жыл бұрын

thanks for the reply!!

Hi again I jetted my bike and now wen I am riding 4-5 gear and gives full throttle somthing is wrong what do you think it is it feels like it’s runing better on choke does that mean it’s getting to little fuel or to much is it enough to turn the mixture screw or what do I do

@Jadams1911

6 жыл бұрын

First turn the PMS screw in and seat it lightly, then back it out 2 1/2 turns. Now get the bike at operating temp. Now start adjusting the idle screw, make sure the bike idles around 900 rpms. anything lower then that doesn't produce the correct oil pressure.

Спасибо большое!

@Jadams1911

5 жыл бұрын

пожалуйста

Quick question...what’s that thin short tube for at bottom of the float bowl?

@Jadams1911

5 жыл бұрын

It's a drain tube.

@BeingJermaine

5 жыл бұрын

Thank you

What is that cable coming off the carb with a plastic head that looks like it can be turned

@Jadams1911

6 жыл бұрын

That is the idle control cable. Do not adjust it if your bike is running well. The idle control will affect how the bike runs because it works with the PMS screw.

I have 2005 roadstar 1700. My question is. Will 2003 carburator fit in it?

@Jadams1911

7 жыл бұрын

Yes, the carbs are the same except for the jets, the manifolds are different.

anyone ever remove the accelerator nozzle? Know where to buy one? i bent and broke mine and need to replace it

where did you get the rebuild kit? I have an 04 1700

@Jadams1911

7 жыл бұрын

www.yamahapartshouse.com/oemparts/c/yamaha_motorcycle/parts?gclid=Cj0KEQiAperBBRDfuMf72sr56fIBEiQAPFXszQS0hAGYwcLyKiimM4Exy7HxGgXPU-iN9oshbye0RHQaAvG88P8HAQ

Men I bought a bike that is been sit for a while, i took the carb out and disassembled it, everything but the screw where that hols the needle set is stripped and I can get out, don't know what to do. Any ideas

@Jadams1911

4 жыл бұрын

First remove the float then spray the screw with pb blaster or wd40. Using a set of needle nose vise grips clamp it on the screw and gently work it back and forth until you feel it break loose.

@csiautodetail

4 жыл бұрын

@@Jadams1911 thank you for the helo, I got it out. Have a great week!

Thankyou

A bike I bought (Roadstar 1600) sat for 19 months, runs like crap. I put seafoam in the tank and start it daily hoping it will clean out..Pull the choke out a bit and it runs great??? If I tear that carb apart to clean it, I might as well scrap the bike, I just don't have the where-with-all to do something like that...anyway I can send it to you. I'll pay you to clean it...I just don't trust anyone around here to do it.

Wbat is the part # for the brass fitting in between thr main jet

Dang, dude. Do NOT use a Phillips screwdriver. They NEED JIS (Japanese Industrial Standard) crosshead screwdrivers. They fit the slot better and doesn’t gouge out the head.

Anybody ever went threw and cleaned carb three times. As in removed and installed and the bike still run like crap. Completely rebuilt and cleaned. Bike spudders badly when you accelerate. Idles amazing.

It's called an Emulsion tube , not a nozzle. Just fyi

Taking the diaphragm out you say use a Philips screw driver - big no. Always use JIS screwdrivers, using Philips screwdrivers is why you see the screws on carbs and particularly brake fluid reservoirs rounded off.

any idea what brand carb that is?

@Bigd1137

4 жыл бұрын

Mikuni

Does anyone know the float adjustment?

@Jadams1911

2 жыл бұрын

I usually check mine with the carb removed. You need to attach a clear hose to the bowl drain tube, attach the gas hose to a fuel supply jug, next hold the carb straight. lift the clear tube up and hold it above the mating surface where the float bowl attaches to the carb, Turn the fuel supply on, Now loosen the drain screw, The fuel should rise up to and be even to where the mating surface of the float bowl is.

Good job