Thank you! Nothing like a good visual before I start. Much appreciated

Great video. Easy as piss haha thanks mate. Wondering why most older American models always look more rusted.. weird.

@Lilmiddwest

3 жыл бұрын

I live Midwest in USA so there snow and salt the roads. If I was from the south they have more cleaner cars and trucks. I don't know if you guys have snow.

Lilmiddwest, i don't understand in this video you say that you have a problem using the aftermarket CV axle and that it would throw a code being that the tone rings are different from the oem tone rings so you went with original OEM genuine hyundai CV axle but yet in the video looks like you were installing a new set of aftermarket axles? If you don't have ABS and the tone ring is there then why is the speed sensor reading of the rings isn't the speed sensor located on the transmission? Also you said when you were running the aftermarket cv axles and it threw a code what is the car doing were you able to drive the car normally? You mention in the video you did a clutch job did you do a video on that? and how did you pull the transmission out to do the clutch on it i know the subframe on these Tiburons are designed so if you try to drop the transmission out from the bottom of the car it blocks the transmission from coming out? I have a 2003 Tiburon GT 2.7 6-speed transmission i'm doing a clutch replacement on it the problem is that i can't drop the trans out of it from the bottom because the subframe is in the way so i pulled the whole motor with the trasmission out from the top of the car using a engine hoist plus it would be difficult anyway if the subframe was not in the way to drop the tranny from the bottom of the car the motor would be supported by one engine mount, the other 3 mounts are off the transmission so you can't leave the motor hanging on one mount while the transmission is out.

@Lilmiddwest

5 жыл бұрын

i have a hyundai tech that work for hyundai since early 2000s and see aftermarket cv axles come off tiburons ,elantra ,sanata and etc. I have a 2005 hyundai tiburon GT 5 speed without ABS but it only has a one speed sensor on the right front for the ECU to read the speed . The one on the trans is for your gauge . i have a code P0501 Vehicle Speed Sensor Range/Performance so that mean ECU cant read how fast you are going , so let say you wana race someone but ecu will cap off your revs up to 5000 rpm so when i go race at the track i ease the code. so i replace 3 cv axle and 2 sesnor so im belive i have a short in the wiring harness between sensor and ecu... i pulled out the snap-on scanner and try to read my speed when i was driving and ecu dosent see the speed and i try other cars and it can read the speed.... and you ask about the how to remove tans without taking off the motor i was holding the engine with the cherry picker up and i move the sub-frame down enough so i can slide out the trans out .You said you have a 6 speed it might be bigger then 5 speed but cant say if it is or not . i have a video here when i did my clutch job

Hey I was wondering what part was named in 4:05 of the video I can’t seam to hear it clearly and the same part broke in my car so I need to fix it thanks would be much help!

@Lilmiddwest

3 жыл бұрын

What outer tie rods ends.

What brand of cv axle are you running rn with out any problems, I need it for racing, with exact speed, for V6 05 gt tiburon

@Lilmiddwest

2 жыл бұрын

One side is oem and cheap aftermarket. I still have same problem but I not running stock ecu anymore. I'm running standalone ecu an AEM Infinity 506

What made you change the axle. I got mine that shakes at 50mph

@Lilmiddwest

5 жыл бұрын

One my axle the boot was ripped and grease was coming out. And I had code for P0501 speed sensor. If shakes at 50mph you should check your wheels balance first.

@dennisluna3508

5 жыл бұрын

I just did CV axles, tie rods, sway bars,ball joints, coilovers, and did alignment definitely feels way better now

I just had both front axles replaced on my 03 Hyundai Tiburon at the dealer.... cost about $1,000.

Hey, curious as to how long this took you. My cousin needs his replaced and I was thinking of helping him with it. But I don't want to spend 4-5 hours in the Florida heat.

@Lilmiddwest

5 жыл бұрын

If everything goes smoothly a hour to 1.5... But if you have all the tools.

@Cyemese

5 жыл бұрын

@@Lilmiddwest I live in a mechanic shop. We have pretty much all the tools. But that seems like a fair time. I'd expect 2 hours or so if it doesn't go smoothly.

What's up bro, I tried removing my cv Axle but had no luck like you being able to easily remove it from the inner joint. I tried pry bars and still can't get it off. Any other way I may be able to remove the cv Axle

@Lilmiddwest

2 жыл бұрын

On transaxle side with Bigger pry bar and a good size sledgehammer. On spindle side air hammer or heat it up and use a hug hammer to hit it out

@jorgealvarado7933

2 жыл бұрын

@@Lilmiddwest any chance of me damaging or bending anything if I go hard on it?

Hey I had a question how many splines does the drivers side axle have for 03 gt 5 speed replaced mine around the beginning of the year and now the car is sounding like the wheel bearing is growling but it could be the cv axle idk. When Me and my brother changed the breaks last week we were playing around the wheel and there was no play indicating a bad wheel bearing we also started it up mid air no sound kinda lost about it

@Lilmiddwest

3 жыл бұрын

It's call brakes not breaks.. Dose it sound different when turning?if so the you have a bad wheel bearing if not I could be your tires. You know when bad wheel bearings sometimes don't have play just staring to go bad.

@faize28

3 жыл бұрын

@@Lilmiddwest ha ha sorry autocorrect. no haven't noticed any sound when turning just accelerating like a low growling sound. And the tires a basically new not even 1 year old and I also did a tire rotation when we changed the brakes.

@Lilmiddwest

3 жыл бұрын

@@faize28 when turning it will put a load on wheel bearing so it will change noise. When going faster it will get louder and if wheel bearing is very bad your steering well be off. I replaced one of my front wheel bearing because my steel wheel was off and it was grinding. You should look at your tires to see if they are wearing even or chopped up..

@faize28

3 жыл бұрын

@@Lilmiddwest just went for a short drive didn't hear nothing when turning. And last week when we did the brakes I rotated the tires and no unusual wear on them

@Lilmiddwest

3 жыл бұрын

@@faize28 then it's not your bearing. Sound like it's hour backing plate. The plate is behind your brake rotors that is touching it

I remove it to change a broken boot. Now the car vibrates constantly when going over 60mph. Any suggestions? Thanks !

@Lilmiddwest

3 жыл бұрын

Did hear it snap ring make click in and make sure axle is all the way in??

@MegredyPhotoStudio

3 жыл бұрын

@@Lilmiddwest my tiburon is a 4 stroker, if the axle shouldn't be all in, I guess it should be an oil leak.. but it's all clear. I couldn't remove the shaft from the engine mounting side [I guess it's called a tripod mount] . I have tried to pull it out to no avail. I'm suspecting that tripod mount is shut...

@Lilmiddwest

3 жыл бұрын

@@MegredyPhotoStudio 4 stroker?? You mean four banger, beta aka 2.0?

@MegredyPhotoStudio

3 жыл бұрын

@@Lilmiddwest yeah, 4 banger 🙂 sorry for my English.

@Lilmiddwest

3 жыл бұрын

@@MegredyPhotoStudio well I'm sure replacing your alxe will be same as Honda, eclipse gst and etc. I'm sure you guys one long axle and one short axle. I used pry bar like I did in the video it sometimes take more time to take them off

I have the 03 Hyundai Tiburon and have had the clutch replaced three times it's apparently some kind of a manufacturer's defect a hole needs to be soldered or something but Hyundai says it's not a recall

@Lilmiddwest

Жыл бұрын

You replace clutch 3 times. You ever did slave cylinder mod? Be if you don't that big reason why clutch don't last...

@GrumpyCat24

Жыл бұрын

@@Lilmiddwest not sure to be honest. You may be right.... It's been about 5 years since I replaced it last.... it has 220,000 miles on it hopefully I don't have to replace it again 😅

@Lilmiddwest

Жыл бұрын

@@GrumpyCat24 if go out again should go with stage 1 clutch vs oem ones. I ran clutch master stage 3 double miles then OEM clutch.

I should have had you replace my axles instead of the dealer lol. How often do they need to be replaced? Mine were leaking. Not sure what but the told me they were leaking. Guessing grease. Lol

@Lilmiddwest

Жыл бұрын

OEM axle are expensive vs aftermarket ones. I can't really tell you how long they last. I have used different brands and cheap ones boot don't least as more expensive brands.

are the 6 speed same as 5 speed?

@Lilmiddwest

4 жыл бұрын

To do cv axle yes and mostly all fwd cars. But transaxle are different 6 speed is Nissan and 5 speed is from Mitsubishi

@lamboking8able

4 жыл бұрын

@@Lilmiddwest thanks for the heads up

Where can I buy a oem at?

@lukeachenbach2325

4 жыл бұрын

And if I get a aftermarket one what could go wrong?

@Lilmiddwest

4 жыл бұрын

Buy at dealership or Hyundai oem parts. Some aftermarket are bit short and speed gear might be wrong.

as in aftermarket you mean eBay or auto zone?

@Lilmiddwest

7 жыл бұрын

rushking19 aftermarket like you get from autozone, advance auto, bumper to bumper, Napa, O'Reilly, rockauto any other part store.. I have a Hyundai tech that work on hyundai since late 90s tell me that some aftermarket CV axle are bit shorter and the tone ring are not same as OEM. He seen customer car that CV axle pop out and have that same code that I have Po501.. I now I have too see If I have a short to ground or and open between my wheel sensor to ecm..

@rushking19

7 жыл бұрын

Lilmiddwest makes sense I plan on getting new ones and saw some on eBay for not to bad of a price I assume it's oem how much did you pay for your axles?

@Lilmiddwest

7 жыл бұрын

rushking19 OEM $300 I thought it will fix my problem.. Rockauto.com was 70 a peace.. I have Po501 since I did my clutch job... Make sure you get the right ones because I don't a have abs.

@rushking19

7 жыл бұрын

Lilmiddwest you also have the 5 speed, I have the 6 and pretty sure 6 speed all of them are abs

@Lilmiddwest

7 жыл бұрын

rushking19 Idk about 6 speed.. I'm trying to get a 2005 and newer 6 speed tiburon just want to see what's different but it has to he all stock..

Very nice video, is your transmission manual?

@Lilmiddwest

2 жыл бұрын

Yes it's a 5 speed manual

@bluetuscani5607

2 жыл бұрын

@@Lilmiddwest It's kind of weird cause I just checked them on their official website and it's the same model for AT and MT, that can't be right HY-8098.

@Lilmiddwest

2 жыл бұрын

@@bluetuscani5607 it could be the same for 4 speed trans and 5 speed manual. I know for sure 6 speed vs 5 speed manual are different.

@bluetuscani5607

2 жыл бұрын

@@Lilmiddwest Well mine is AT

@Lilmiddwest

2 жыл бұрын

@@bluetuscani5607 I kind of figured you had automatic. I only worked on automatic Tiburon once I can't tell you what's different between automatic vs Manual

Amateur. Nice topic though.