Thank you for posting this i found it showed my father-in-law. I went and bought the tool and the stress was less. Thank you for doing the video

@AndyMahnFL411

Жыл бұрын

I'm very happy to help, thank you for posting your comment, sounds like you got the job done!

@daviddanberg3026

5 ай бұрын

That thick washer belongs between the tub and the drain. 15:05

The gasket goes between the bottom of the tub and the drain pipe, especially since you didn’t put any thread sealant on.

Excuse me mister master plumber you're supposed to put the black washer in between the tub and PVC pipe. That's my tech tip for the day

For anyone watching this now, you would want to use a tub drain wrench, not an extractor tool. You only use that if the drain is missing the cross bar inside of the drain. The tub drain wrench would have removed that a whole lot easier! I am doing this and the overflow, and all the faceplates in my 1860s home tomorrow. Wish me luck! Also, the gasket does not go there. It goes between the bottom of the tub, and the top of the pipe. 😮 I hope u fixed that! I wonder how many people ha e done it wrong now...

@AndyMahnFL411

8 ай бұрын

You might notice that one of the cross bars was missing, thus the reason to use an extractor tool, in case the metal cross was weakened/compromised to the point at which a drain wrench would break that part further. So in this case, the extractor tool was the correct choice. And thank you for the point regarding the gasket, correct. Good luck on your project.

@markhogan1633

7 ай бұрын

Hope your project went smooth. Home from 1860’s…I’m jealous…

@HappyPenguin75034

7 ай бұрын

Cross bars will break on old ones

I got the same drain extractor tool because I was a bit in a hurry to replace two tub drains in my newly purchased home and I could not find the wrench in a nearby brick & mortar. I recently used it to replace the same tub drains because they had corroded. I always place material like a small, folded rag/towel on top of the extractor before banging on it with a real hammer. Has not failed me so far. And I always use plumber's putty as you did instead of the included rubber gasket. Before I had purchased the extractor tool, I did a bit of research and learned from another YT clip that there was a rubber gasket between the PVC drain pipe and the bottom of the tub; this gasket was the exact same size as the one included with the tub drain, so I used the new gasket for this purpose.

@AndyMahnFL411

6 ай бұрын

Thanks for sharing your experience and what has worked for you. Also, as you and several others have pointed out, the gasket should be placed in between the tub and the drain pipe. Best wishes for the new year.

Excellent demonstration. I like that things that can go not quite according to plan can happen and how to resolve. Thank you!

@AndyMahnFL411

2 жыл бұрын

Thank you, and I didn't realize how relatively easy it was to remove this ugly drain hardware, just took a little bit of elbow grease, plus the correct tool which did the trick.

Thick washer goes between the tub and the pipe. 😮

Yes it was a good informative video but yes I have to agree with the previous message saying the gasket goes beneath the tub not under the drain

great video this is exactly how difficult it is to remove an old rusty drain...its gonna take some real elbow grease.

Subscribed brother! This is how I'mma spend my father's day! Got 2 of those too replace

@AndyMahnFL411

Жыл бұрын

You can do it, extra points for knocking them both out!

Thanks for this diy. Mine looked like that. On my way to Lowes to buy the supplies needed.

@AndyMahnFL411

Жыл бұрын

Good luck, may require some elbow grease, if you know what I mean, depending how long the drain has been in place.

👍 Good job !

Thanks for the video...

Rubber gasket goes between your tub and the drain pipe!

Great! The best demonstrations I’ve seen! 👍🏻

@AndyMahnFL411

Жыл бұрын

Thank you! Hope it helped.

Is it possible to damage the tub while you're unscrewing the drain with that tool? I'm a bit afraid that I'll cause even more damage when I'm trying this. My drain is corroded just like yours.

@AndyMahnFL411

2 жыл бұрын

I was surprised by the amount of force required, but again the drain has been in my tub for many years. You need to apply downward force while you're also using the tool to unscrew it, it should and will come out. Good luck!

What about the gasket

looks ok to me

Put gasket between bottom of the tub and the drain pipe.

I have that exact same extractor tool - and my drain looked exactly like that. That tool doesn't work at all for me though. Can't get the knurls to catch! I tried not to wail on it but all the tool did was destroy the drain while I was trying to get it secure enough to catch

@AndyMahnFL411

2 жыл бұрын

I have to admit, it took more force than I would've expected, particularly when hammering it in to try to get it to catch the metal appropriately. I just went for broke and ultimately was successful. It's up to you, good luck!

@Shawdiee

10 ай бұрын

I'm currently having this issue - no matter how hard I use the mallet, it's just bouncing around in the drain hole. Did you find another solution or did you end up calling a plumber?

@philm.2812

10 ай бұрын

@@Shawdiee No luck with that thing, I think I put on my grumpy face and returned it to Lowe's (?). I ended up borrowing my highly skilled neighbor and his arsenal of tools. We very carefully cut it out with one of his saws, a dremel and so files. What a pain.

@tammyellen6366

29 күн бұрын

@@AndyMahnFL411need help!! I used the tool to try to get old casket out but the only thing that came out was the corroded plate that sits on the tub. I’m afraid to put pressure on turning because the tube inside Drain was moving. I wish I can show you pictures of it.

@AndyMahnFL411

29 күн бұрын

@@tammyellen6366 sounds like you may need a different type of tool, perhaps a drain extractor wrench, something that can grab onto the crosshairs and help you extract it that way.

That gasket goes below the tub

Seal goes in under tub then the new putted drain ..

@AndyMahnFL411

2 жыл бұрын

Yep, thanks Sassy

@BaltoAmy

10 ай бұрын

How do you get the seal in there? Is there an old one you need yo remove first?

A pair of channel lock pi

how to replace tub drain - HARD! - fixed it

@AndyMahnFL411

Жыл бұрын

Let's say 'your mileage may vary', in terms of the difficulty level, it's usually just a matter of how tightly the drain is screwed on and how long it has been in place.

The gasket, goes UNDER the tub, above the pipe... Not under the screwed-in drain plate/face. LOL. You're welcome.

@AndyMahnFL411

2 жыл бұрын

Correct, in most cases will be easy enough to do by inserting the gasket into the hole to let it rest in between the tub and the elbow of the drain pipe that the new threaded drain screws into. There could be lots of old crusty plumbers putty in there (or an old worn gasket) to remove first. That thick rubber gasket completes the seal on the underside of the tub.

@eddiekay9019

11 ай бұрын

He has no access, unlike a sink.

@elliotromero4411

9 ай бұрын

Why are you pretending to know that. You even mentioned it incorrectly in your video kzread.info/dash/bejne/k6Nr26Nyfby2Z6Q.html @@AndyMahnFL411

@elliotromero4411

9 ай бұрын

Incorrect. You can get the gasket inserted easily and if needed you can use a screw driver to help create a bigger gap. @@eddiekay9019

@garrygiordano4059

Ай бұрын

Treaded portion of drain pipe is called the “shoe”

My drain was so corroded that tool just kept grinding it up more

@AndyMahnFL411

5 ай бұрын

You could try a drain wrench, I found that in my case that I had to hammer in the extractor tool considerably before it was actually able to grab. Good luck!

Your rubber seal should have been used under the tub . . . .

Hit it with. Your purse

@johnnyfigueroa4690

3 ай бұрын

😅

Beep boop bleep

@AndyMahnFL411

2 жыл бұрын

you said it!