LEFT REAR WHEEL has a reverse thread by the way, just doing mine now, Excellent video! Nice and to the point!
@popcornisgood10 ай бұрын
Really appreciate the tight editing! Most car how-to videos I immediately set to play at 1.5 speed, but no need on this one.
@Kernomadz4 ай бұрын
Literally today, I followed this and changed my tone ring. Many thanks. Great video! To the point, covered each step and made sense! Great work! 😊👍
@richardgranato6707 Жыл бұрын
Quick, to the point, and still full of the proper details. 👌 Thank you this helped me tremendously!
@user-iy3mm9oi6k Жыл бұрын
this is how all diy videos should be
@LG-kl3co2 жыл бұрын
One of the best video's I have seen !
@johnt97543 ай бұрын
Great video, well done quick and to the point , I appreciate that , I can tackle this job now .
@Nick_Greenfield4 ай бұрын
Perfect video, thanks! Will be doing this on Saturday
@mutts3026 ай бұрын
Thanks bro you’re great 👍
@user-ni1cw6vw8p Жыл бұрын
Great info and video
@ramiabed74695 ай бұрын
You are so smart I like your job
@SuperBroop5 ай бұрын
Very good video. Thanks!
@brianwelch79758 ай бұрын
I have to replace mine that split the same. This is helpful thank you. Only thing I'd add to the video and I'm not sure this matters or not but when I replaced my rotors for ventilated discs I marked the axel to fit back in exactly the same as when I pulled it out. Again may not matter but I figure better safe then sorry to fit it how it was already seated. Thanks again.
@nexpro6985 Жыл бұрын
Great vid. Thanks.
@theredbagger Жыл бұрын
Great how to.... why can't all how to be like this 👍
@robertsyrobbo2501 Жыл бұрын
Do you have to pull that half Axle to access wheel studs ?
@mozer302 жыл бұрын
Just a word of warning. There’s a special seal that fits in the hub, and upon removal can be damaged. It’s a 2 piece seal, which can pull apart, leaving 1 half in the hub, and the other on the axle. It cannot be repaired as it distorts when the hub is removed. You may want to order a seal to be on the safe side as this happened with only 40k miles on the clock.
@cameronmarshall1829 Жыл бұрын
Hi is this the same for rear left wheel, torque sequence the same and hub nut isn’t reverse thread?
@MartinezRE110 ай бұрын
Excellent video but I would have done a wheel seal or hub seal
@Yoosta_yoop Жыл бұрын
Thanks! Now I know I’m not fixing it myself 😒
@costascosta49606 ай бұрын
should the warning lights go out after a reset or only on a test drive
@chrismacmillan2795 Жыл бұрын
So, I have a abs light on even after I've replaced the sensor, would a broken ring cause this ? Many thanks
@michalpovolny8461Ай бұрын
:D .. i just jack the car clean the ring while its still on there is little space to do it then use epoxy glue and big hose clamps to hold it and its 200 000 km fine ... ofcourse it my car ... let the customers pay :D
@wxfield2 жыл бұрын
Our fix was to pull the fuse for the ABS and cruise control. Cheap, effective and makes you drive & brake like the old days...courteously and carefully.
@livefree6878
2 жыл бұрын
I’m glad I didn’t know how much work it was when I started the project. It took all day, it was like a day at the gym. 👍👍
@wxfield
2 жыл бұрын
@@livefree6878 Yeah, it's pretty awful work. On all my Chevy trucks I've always said, "Over 100k miles means no more ABS or cruise control" Out comes the fuse.
@dylanpottery
Жыл бұрын
You don’t think a broke ring could cause more damage down the road?
@wxfield
Жыл бұрын
@@dylanpottery For me, it never has been an issue. But most of my trucks on the farm here are at least 1 ton..so maybe that makes a difference. I think if it were a more normal truck..like a half ton, I might just replace it all. Those parts (in their entirety) seem a lot cheaper than the larger truck parts.
@dylanpottery
Жыл бұрын
@@wxfield gotcha I have a 350 transit just got myself an this exact issue just happened but I’m contemplating having the shop even do it now after seeing just how big a job is an really wanting to make sure if it’s done gets done properly with correct torquing an backing off after compression
@dbbaileys6 ай бұрын
Looking for the right size bearing socket wrench . Anyone knows where I can purchase one?
@williamcastro3381 Жыл бұрын
una pregunta como se llama la eramienta que usa
@897aa33 Жыл бұрын
I think differential oil on transit should be 1 cm below the hole.
@arturomurillo570325 күн бұрын
hello my friend do you have the item number for the ring?
@travismcleod56752 жыл бұрын
would this be the same as a ford transit 250?
@Da305Alive
Жыл бұрын
Yes
@marcinszczoczarz6083
10 ай бұрын
Where can I get ?
@jonataseuuk9 ай бұрын
It's a fucking headache 😂😂😂 unless you have all the tool don't try I've done it , took me 2 days
@ollie22426 ай бұрын
Not a very good video sir could have did a better job explaining things
@Kernomadz
4 ай бұрын
Totally disagree. It was to the point, covered each step, and nowhere in the title did it say “for beginners” so I used it, and had great results!
Пікірлер: 41
LEFT REAR WHEEL has a reverse thread by the way, just doing mine now, Excellent video! Nice and to the point!
Really appreciate the tight editing! Most car how-to videos I immediately set to play at 1.5 speed, but no need on this one.
Literally today, I followed this and changed my tone ring. Many thanks. Great video! To the point, covered each step and made sense! Great work! 😊👍
Quick, to the point, and still full of the proper details. 👌 Thank you this helped me tremendously!
this is how all diy videos should be
One of the best video's I have seen !
Great video, well done quick and to the point , I appreciate that , I can tackle this job now .
Perfect video, thanks! Will be doing this on Saturday
Thanks bro you’re great 👍
Great info and video
You are so smart I like your job
Very good video. Thanks!
I have to replace mine that split the same. This is helpful thank you. Only thing I'd add to the video and I'm not sure this matters or not but when I replaced my rotors for ventilated discs I marked the axel to fit back in exactly the same as when I pulled it out. Again may not matter but I figure better safe then sorry to fit it how it was already seated. Thanks again.
Great vid. Thanks.
Great how to.... why can't all how to be like this 👍
Do you have to pull that half Axle to access wheel studs ?
Just a word of warning. There’s a special seal that fits in the hub, and upon removal can be damaged. It’s a 2 piece seal, which can pull apart, leaving 1 half in the hub, and the other on the axle. It cannot be repaired as it distorts when the hub is removed. You may want to order a seal to be on the safe side as this happened with only 40k miles on the clock.
Hi is this the same for rear left wheel, torque sequence the same and hub nut isn’t reverse thread?
Excellent video but I would have done a wheel seal or hub seal
Thanks! Now I know I’m not fixing it myself 😒
should the warning lights go out after a reset or only on a test drive
So, I have a abs light on even after I've replaced the sensor, would a broken ring cause this ? Many thanks
:D .. i just jack the car clean the ring while its still on there is little space to do it then use epoxy glue and big hose clamps to hold it and its 200 000 km fine ... ofcourse it my car ... let the customers pay :D
Our fix was to pull the fuse for the ABS and cruise control. Cheap, effective and makes you drive & brake like the old days...courteously and carefully.
@livefree6878
2 жыл бұрын
I’m glad I didn’t know how much work it was when I started the project. It took all day, it was like a day at the gym. 👍👍
@wxfield
2 жыл бұрын
@@livefree6878 Yeah, it's pretty awful work. On all my Chevy trucks I've always said, "Over 100k miles means no more ABS or cruise control" Out comes the fuse.
@dylanpottery
Жыл бұрын
You don’t think a broke ring could cause more damage down the road?
@wxfield
Жыл бұрын
@@dylanpottery For me, it never has been an issue. But most of my trucks on the farm here are at least 1 ton..so maybe that makes a difference. I think if it were a more normal truck..like a half ton, I might just replace it all. Those parts (in their entirety) seem a lot cheaper than the larger truck parts.
@dylanpottery
Жыл бұрын
@@wxfield gotcha I have a 350 transit just got myself an this exact issue just happened but I’m contemplating having the shop even do it now after seeing just how big a job is an really wanting to make sure if it’s done gets done properly with correct torquing an backing off after compression
Looking for the right size bearing socket wrench . Anyone knows where I can purchase one?
una pregunta como se llama la eramienta que usa
I think differential oil on transit should be 1 cm below the hole.
hello my friend do you have the item number for the ring?
would this be the same as a ford transit 250?
@Da305Alive
Жыл бұрын
Yes
@marcinszczoczarz6083
10 ай бұрын
Where can I get ?
It's a fucking headache 😂😂😂 unless you have all the tool don't try I've done it , took me 2 days
Not a very good video sir could have did a better job explaining things
@Kernomadz
4 ай бұрын
Totally disagree. It was to the point, covered each step, and nowhere in the title did it say “for beginners” so I used it, and had great results!