Repairing Lee Precision Lead Pots (Replacement Parts)
In this episode we repair my Lee Precision Production Pot IV by replacing the pot and the pin due to impurities and rust sticking to the side of the pot over the last year. Its much cheaper to repair these than buying a new one. Once you click on the links below, find the link for parts.
Production Pot IV
leeprecision.com/production-p...
Pro 4 20lb
leeprecision.com/pro-4-20lb
Precision Melter
leeprecision.com/precision-me...
Barlow's Tackle (Affiliate)(Code: B8NTACKLE)(NO DISCOUNT)
Click here to help support this KZread channel as anything bought using this link....
www.barlowstackle.com?afmc=B8NTACKLE
Epic Bait Molds
epicbaitmolds.com/
Hog Salad Bait Molds (Affiliate)(Discount code: B8N10)
hogsaladbaitmolds.com?aff=22
Slim's Website
slimslures.com/
CNC Molds and Stuff
www.cncmolds.com/webstore/
Thank you so much for all of your support!
Music: KZread Studio Track
Пікірлер: 30
Great video, thanks for sharing.
Very good tutorial for your community. Be blessed. My friend.
@B8N_Tackle
7 ай бұрын
Thanks Joe!
Good job! Nice video with some helpful information! Appreciate you and what you do! Keep up the good work!
@B8N_Tackle
7 ай бұрын
Thanks David!
Good video!! Thanks
well, ive had my 20 pound pot for ever 3 years, and im still using it to this day ,,, people,, you have to FLUX,, your pot and clean it right out from time to time.. and you will have no problems. and i have made thousands of jigs and even lead weights for fishing nets
@Starman2440
2 ай бұрын
Absolutely, positively 100% correct. Been using a Lee Production pot 10 lb since the 70's. The pot on it has almost no gunk buildup on it. To remove the small amout it has I use a wire wheel on an electric drill and do this outside, wind at my back....takes seconds. One should always put a light coating of oil or wax on the steel parts, after it has cooled, if you don't use it for awhile---it will then stay rust free.
@B8N_Tackle
2 ай бұрын
Guys I completely agree with both of you but it also depends on the quality of lead that you put in your pots. Again I found a huge stash of soft lead in an old shower liner from the 70's, it has a ton of impurities. For me this was the best option. I can't use flux since I'm using my pots inside my house in a small vented enclosure. I'm not cool with a flux fireball inside my house, lol. The parts are cheap and easy to replace. That was the point of the video. If flux works for you, keep rocking on bros!
@capspik
Ай бұрын
And don't melt copper gas checks in with your batch
Perfect timing! I need to do this too.
@B8N_Tackle
7 ай бұрын
Awesome man! Hope it helps
I do the same thing and just replace the pots when they get dirty. They are too cheap not to
@B8N_Tackle
7 ай бұрын
You got that right my man!
Ive been using my melter for years and have never had it look that bad. Do you flux your lead. Every thousand bullets i cast i drain the pot and use steel wool to clean it. Biggest issue i have is the thermostat goung bad.
@B8N_Tackle
Ай бұрын
It's because I have alot of impurities in the lead I found and use for now. Can't flux inside my vent box made of wood. Rather not burn the house down lol.
We’re did you get your large ladle that has pour spout at???
@B8N_Tackle
5 ай бұрын
I have 2 laddles, one is from Barlow's called the small lead laddle, the other is the lyman casting dipper from bass pro.
Do u have a extra coil ? I need and. Ant find the coil .
@B8N_Tackle
5 ай бұрын
Go to lee precision website, link is in the description.
Also does your 20lb pot leak like the smaller Lee pot does?
@B8N_Tackle
5 ай бұрын
Leak front the nozzle?
@nightguy4163
5 ай бұрын
@@B8N_Tackle yes
@B8N_Tackle
5 ай бұрын
@nightguy4163 occasionally yes it does, you need to clean it out from time to time, sometimes I use a long piece of wire to shove in the hole from the bottom to clean it out, just be careful. You can also just run a bunch of hot lead through it, sometimes this works.
@nightguy4163
5 ай бұрын
7@@B8N_Tackle so it is just like the smaller pot lol thank you!
I need that coil u had laying there lol lmk
@Aim2jig
5 ай бұрын
Is it possible? Mines burnt out n can't find replacements
@B8N_Tackle
5 ай бұрын
@@Aim2jig go to Lee precision website, link is in the description bud
I have been using lee pots since i was 15 im now 34. If ya damn flux with beeswax or saw dust you wont have this problem. Along with skimming dross and disposing it accordingly.... This is absolutely ridiculous Ive made thousands of bullets and my oldest casting pot is still going strong with no replacement parts......
@B8N_Tackle
4 күн бұрын
@michaelkaminsky9914 as I've explained before, I'm using this inside a small vented box, I cannot use flux and burn the house down. I skim the lead all the time and don't do this that often, like every couple years. If I could flux I would. This is also a video on how to replace if you had to, not shooting down what anyone does. Get off your soap box bro. I'm not offending anyone in here and you have your own opinions.