The mistery of how to re assemble the flywheel halves solved . Iv never seem it done before . I had no idea that the runnout could be adjusted so easily with a copper hammer . I had imagined a press would have been required to slide the pin.Thanks .

Более шикарной работы с коленвалом я не видел

Bravo Paul c'est magnifique 👍👍👍

Amazing your videos make me relax

Excellent work Paul, Bravol!!!!👏👏👏👏👏👏

Nice job. Using heating and cooling spraying is good. If Crank assembling fixtures use no need to hammer and truing Crank. 👏👍👌

Смотрю с удовольствием.Творческих успехов Вам.

Amazing, you sir have got a gift.

Como siempre muy buen trabajo y buen video.

Thanks! Awesome work!

Another great repair.

WONDERFUL! You have a new fan rigth here. Keep going! I would love to see more of your work!

congratulations, beautiful job

I luv machinist that rebuild 2 steoke engines they do it the right way

Great repair👍

See, two strokes are easy...

Excellent work

Excellent work 🇵🇹🇧🇷

awesome job👍🏻👍🏻

Nice repair tips bro

sei bravissimo

neskutočne pekná robota....

Supernice work 👌👍👍👍

Magnifico!

Nice machining

Very good job

Very good!

Klasse! Du bist nicht zufällig aus Deutschland? 😅

Ufff... sin palabras. 💪💪💪

Better than new!

You're good dude !

Love videos 😀

impressive

now if the owner can just keep oil pressure high enough so that the engine doesn't seize again?

Good job

Amazing, why cant u be my big brother, i mean im 30 but i need a big brother with such knowledge ;D haha

Klass 😁👍

Awesome

👍🏻👍🏻

👍👍👍👍👍

Nice work, but splitting a crank like that is not a great idea !

@nepicness

3 жыл бұрын

What’s a better way?

@ridbanner1407

2 жыл бұрын

@@nepicness cutting the pin in half through the rod and pressing the two half pins inward causes much less damage to the webs.

cool

Are you using Iscar tooling? 4140 or 4340 Good job.

Clean job. Do you expect any crack on the thread with the hole trough?

@PaulXchannel

3 жыл бұрын

Thanks. Shaft insertion overlap is correct.

@Drottninggatan2017

3 жыл бұрын

Might have been safer to loctite it in and use a looser fit.

@PaulXchannel

3 жыл бұрын

This video is for masters of shaft pressing. I normally use Loctite :) See my other videos.

What a ridiculous construction! The crankshaft is basically part of the water pump? Never seen that before, usually there is some kind of coupler in between

Доброго времени суток! Хорошая работа! Подскажите где можно приобрести такие нутромеры?

sembra nuovo!!

Exactly, how else would you want to split a crank assembly?

Is there any video on how to align the crankshaft?

What kind of lathe on ur work Paul. Look mini but really great work.

@PaulXchannel

3 жыл бұрын

Thanks. Optimum D320x920

@t2t

3 жыл бұрын

@@PaulXchannel thank Paul. 😍

Good work, but I am surprised it was economically viable to do this repair.

@PaulXchannel

3 жыл бұрын

Thanks. It is old model. In the future will be part 2. Even more work ;)

Лаикккк

Приклинила начали проворачивать и свернули.Заворачиваласи на винт сделал на гайку.

Pushing the rod journal/crank pin through the web sure doesn't do the journal's surface any good, even though you tried to put some lube on it, it didn't do much. Then again, im surprised so many press in piston wrist pins don't damage their surface & score up the piston's bore.

Hi, I just bought aftermarket crankshaft for my Honda Winner 150, the problem is it come with bearing preinstalled on the crankshaft (magnet side). The bearing is a bit bigger compare to original bearing so I cannot fit it onto the crankcase. Original bearing will just slide onto the crankcase. Do you have any idea how can I install the crankshaft?

@PaulXchannel

2 жыл бұрын

Rebuild

Grear repair

Paul excellent work. how could i contact you for a cylinder head repair of a 2008 ktm 505 sxf

@PaulXchannel

3 жыл бұрын

Thanks. Unfortunately i am very busy.

@reimondrodriguez3962

3 жыл бұрын

@@PaulXchannel thank you very much for answer paul I understand that you have a lot of work. I need to fix the cylinder head and I find someone :( whatever you do an exceptional job and I know learn with all that information that you provide us in the videos thank you and blessings

Saya from indonesia

@adibsumairi7143

3 жыл бұрын

Saya from Malaysia

@keongid280

3 жыл бұрын

Salam kenal salam persahabatan

@Drottninggatan2017

3 жыл бұрын

Saya kerenge.