Repair 2000W Suoer Inverter
Ғылым және технология
Buy here:
👉 RD6018W : bit.ly/3oMozQe
👉 5000W: www.banggood.com/custlink/DKG...
👉 Shopee : shorten.asia/dk2nghpW
Today I will show you how to repair inverter suoer 2000AL version 2021.
It has 2000W rated power, 4000W peak power with 16 mosfet HY3506
Video Tiếng Việt ở đây : • Sửa kích điện Suoer 20...
If you like my video, give me a cup coffee. Thank you very much.
Donate : www.paypal.com/paypalme/phdhung
Facebook group : bit.ly/CreativeElectronic
Contact: Magnetron0989821611@gmail.com
Phone: 0989821611
#Inverter
#Repair
#2000W
Пікірлер: 88
Kênh Tiếng Việt : kzread.info/dash/bejne/fWd3uLiFp7CYXdY.html
@tranlong2433
3 жыл бұрын
em có làm mạch dùng 3 cái tg1000 quấn nối tiếp hệ 24v dòng không tải tính cả cầu h luôn cỡ 0.85a thì ổn không vậy anh ?
@PhdHung
3 жыл бұрын
Ok đó, con suoer này ko tải cũng cỡ ~ 0.8 0.9A/12V đó.
@PhdHung
3 жыл бұрын
hehe, Làm thêm 1 kênh VN chém gió cho vui. Live nói chuyện cũng dễ hơn kênh kia á.
@sunuk1915
3 жыл бұрын
Your new channel?
Excellent troubleshooting
Blowing off of inverter IGBT or MOSFET shows, spurious component being used by Chinese manufacturer. Trouble shooting is excellent. Its informative viedo to student as well. Moreover with no nonsense music and well explained with caption. Thnnx.
Incredible. This is really cool to watch. I dont repair stuff like this but i enjoy watching your repair videos. I'm more into electronics DIY or use of software on my channel.
Very good repair video 👍
Back again; man,you're a trully awsome repair man; thanks,that EG3212 just made my day my inverter has a ID2006, and nobody has one , but upon checking....THEY ARE THE SAME, thanks edit it's EG3112 at 06:00 you made a mistake,you wrote EG 3212 ?
Nice project
Very Good
👍Very good and Thanks
thank you sir,,
Hi thank you , I have Suoer FPC-1000A ,It has SWPM driver board 16 pins with lm393 and NE555 ICs exact like you've shown in 9:41 ,So I tried to use EGS002 board with rearrange connections. Finaly it works ,outpot 220 v but Hz oscillate from 80 to 90 Hz. I can't find original board .please help.Note that I dont replace inflated filter caps yet( 220mf /450 x2). Why this problem in Hz?and where do you get 16 pins board. the board set on 50Hz fixed (factory default).
Rất tuyệt vời...
Shout out sir from palawan province Philippines
@techbarron7383
3 жыл бұрын
kumusta,,
I have Suoer FPC-1000A ,It has SWPM driver board 16 pins with lm393 and NE555 ICs exactly like you've shown in 9:41. After replacing all ICs it opens and close rapidly like ringer sound sometimes like Morse code , and the load just flashing very fast. Please what's your advice.
Wow inverter of your country are very advanced .... I don't when they will come to india
Hello, nice Video ! Maybe you can help me ont the following : My victron Phoenix Inverter 12v 750va just doesn't want to start, no led, no noise... I decided to open it and everything seems to be fine : the 3 30A fuses, the small fuse in the switch circuit, all mosfets and diodes. I basically see no short anywhere. It seems more of on open circuit somewhere as no voltage go to the drive board. Any idea where to look at ? are there any other fuses ? Thanks.
Thanks bro. I want to ask, how can one adjust the output voltage of a suoer modified sinewave inverter from 230v to 220?
Thanks for the informative video! I have a bad modified sine inverter. I replaced all faulty mosfets and some burned resistors but it still wouldn't work. Capacitors all seem to be fine. Any idea what to check?
@00000005547
3 жыл бұрын
gate drivers.
Hello. I also have a broken 1500W power converter. Unstable output voltage. it also jumps to 500v. I'm asking for advice, where should I start? Thank you in advance.
Good
Nice presentation and really good work
Hello, 3000 watt solartronics full sinus inverter fault light is on. When the inverter is turned on, a relay tripping sound is heard, then the fault light is on, what do you think could be the problem?
Hi can you make a project about powering laptop with external battery with protection features like balancing, temperature control and charging?
Hi,sir, i have a Easun,also called Powland, 5000 watt inverter,24 vdc to 220vac, that have an upright SPWM board for the 2nd stage, with an unmarked IC, soic-16, do you know what IC that is? its 4 outputs are on pins 5,6 and 8,9 and vcc on 16 and ground on1, i think;
Xin chào, tôi có một câu hỏi về cách làm lại một biến tần điện áp được cấp nguồn từ 48 volt và thêm 220 volt, nhưng để nó được cấp nguồn không phải từ 48 volt mà là 24 volt?
Always a great job. I also have a problem with my inverter and no one can advise me. I don't have 50Hz, but about 1500Hz and I don't know how to fix it. Do you have any experience with this problem?
@PhdHung
3 жыл бұрын
Post the problem to the FB group
Sir Where can you buy spwm?
how can make a drive signal checker homade ?
it really pays to keep the inverter COOL; Add FANS to it,before hand!!!! i do.
for this model i think you dont have to replace driver i once repair one with out replacing the driver ices it worked!
Faz um reparo em um changi 1000w 24v pra nos vê
Hello.a question.can only one pq frrit transformer with that size made some power about 2000-4000 watt.?? I made with a pq87 and 10 mosfet irfp064 but not receive about 1000 watt of that?why?
@amirmahdisalari3528
3 жыл бұрын
چنتا 064 n گزاشتی تعداد دور اولیه و ثانویت چقدره فرکانس کاری مدارت چقدر بوده همینجوری که نمیشه توان بالا گرفت
Why damage the mosfet and IGBT their faulty design right?
@PhdHung
3 жыл бұрын
Overload bro.
Hi my inverter error led lit can cause buzzer buzzing
Hi what's the full part number of the gate driver you used?
@Delali
3 жыл бұрын
IR2101S.
What is the primary and secondary speed of the pq60 transformer and what is the operating frequency of the transformer
@PhdHung
3 жыл бұрын
1 turn + 1 turn - 30 turn @ 30Khz
@amirmahdisalari3528
3 жыл бұрын
@@PhdHung Do you think the frequency of 30 kHz is not low for this transformer and this number of revolutions? I think the frequency should be around 90 to 100 kHz
What size transformer? Ee65?
first
I don't see any heat sink compound?
How to remake a voltage inverter that is powered from 48 volts 220 volts but so that it does not feed 48 volts to 24 volts ?
2021 vs 2020, which one is better?
👍👍
♥️♥️♥️
High side mosfets or all burn this should not had happened the short circuits protection is not adjusted to the power rating why the mosfet burn the potentiometer need to adjust at 2000watt to protect the mosfet from burning
i wrongly connect the dc terminal, pos to neg and neg to pos.. after that, my inverter not working.. can i know what is the problem and it still can be repaired..
@PhdHung
3 жыл бұрын
Check the fuse
Trông mạch không đã mắt lắm nhưng vẫn kết nhất cái biến áp (1 vòng + 1 vòng ,30 vòng)
@PhdHung
3 жыл бұрын
Giờ nó toàn mẫu này thôi. Chạy ko kém mẫu cũ đâu à. Dễ sửa hơn nữa hehe 😁
Anh có làm cái máy hàn cell ko anh
@PhdHung
3 жыл бұрын
Mình tặng PCB thôi chứ ko làm máy bán bạn à.
@nguyenvanlam1802
3 жыл бұрын
Ý em là làm mạch in thủ công ấy anh
@nguyenvanlam1802
3 жыл бұрын
Làm bằng bo arduino,em có tầm 1 tuần trước ấy anh
Stm controller?
@PhdHung
3 жыл бұрын
yes, STM8
Nó dùng IC lập trình ạ anh?
@PhdHung
3 жыл бұрын
Đúng r . STM8 nhé
@ucuc4030
3 жыл бұрын
@@PhdHung em đang thích phần tạo sin từ egs002 quá nhưng làm toàn bị nổ thui ạ😅
@PhdHung
3 жыл бұрын
@@ucuc4030 mua 1 cái PCB là ngon ngay
@ucuc4030
3 жыл бұрын
@@PhdHung nhưng em muốn tự làm dở ở chỗ đó 😅😅😅
Al último no se ve bien el video
ah về chip chưa
@PhdHung
3 жыл бұрын
chưa bạn ơi
cho mình hỏi, mình dùng inverter 24v to 220v sine, đã sửa bị điện lưới xông vào, bây giờ bật buổi tối áp 24v thì ok, bật ban ngày áp sạc 26v dẫn tới đầu ra áp cao chết fet chết egs002, xin hỏi là có cách nào khác phục tình trạng bật ban ngày mà vẫn ko chết inv ko?
@PhdHung
2 жыл бұрын
thêm hồi tiếp cho phàn DC-DC thôi b
@minhphuc1283
2 жыл бұрын
@@PhdHung vậy cho mình hỏi thêm, làm hồi tiếp dc thì mạch nguyên lí vẽ ra sao?
@PhdHung
2 жыл бұрын
hồi tiếp nó có sẵn rồi chứ. Kích nào cũng có hồi tiếp DC, hồi tiếp ac mà
@minhphuc1283
2 жыл бұрын
@@PhdHung mình đã test lại với điện áp 26v kết quả xì khói, còn 24v thì ok. mặc dù dải điện áp cho phép là 24 - 30v. xin giúp đỡ phần này
@minhphuc1283
Жыл бұрын
@@PhdHung hiện tại áp ra khoảng 350 360vdc. Xin hỏi là có cách nào hồi tiếp xuống tầm 310vdc ko? Hồi tiếp từ opto về 3525
Plice give me giveaway
Good