Thank you for this video!!!!

@tractorsmarinemechanic

3 ай бұрын

Thank you for watching.kindly share and subscribe

👍👍👍👍👍👍

Boss Video kadin po ng transmission Gear replacement ng iseki 3510 .

@tractorsmarinemechanic

Жыл бұрын

Kapag may pagkakataon sir.ggwin ko para sayo

Ок

How to identify valve seals are bad ?(how to confirm cause to problem is valve seal or piston rings)

@tractorsmarinemechanic

10 ай бұрын

You can see the oil at the exhaust port

For the D850 engine, what should be the valve clearance?

@tractorsmarinemechanic

Жыл бұрын

Just apply .25

@tadaskabliukas2797

Жыл бұрын

@@tractorsmarinemechanic 0,25mm ?

Hi, im about to do this on my d850. Does the valve need to be stopped by the piston in order to remove the spring lock? If so will it cause damage? Thanks for all the videos :)

@tractorsmarinemechanic

7 ай бұрын

Just put the piston on top and you can remove the retainer.

@user-ep5rp1km4k

4 ай бұрын

Да обязательно,если это не сделать клапан упадет во внуторь..проврежней от этого не будет!

@JohnStardust

4 ай бұрын

Thank you ​@@user-ep5rp1km4k

Добрий день,скажіть будь ласка який зазор робите Ви на клапанах?Дякую

@tractorsmarinemechanic

Жыл бұрын

0.25mm

Boss ilan ang valve clearance Ng Iseki 2210 intake/exhaust?thank you.

@tractorsmarinemechanic

Жыл бұрын

Pareho .25mm Ang nilalagay ko

How do you know when the piston is top dead ceneter?

@tractorsmarinemechanic

3 ай бұрын

kzread.info/dash/bejne/jGydqcqIgsmpZ5M.html

@tractorsmarinemechanic

3 ай бұрын

Just watch my another video and if you don't understand just go back to the comment section and I try tell you how get to know the top dead center

@shhhhawk6053

3 ай бұрын

Thank you! Your videos are awesome! I was wondering how to find top dead center with the rocker arm off and no timing mark. When changing valve stem seals so you dont drop a valve

👍👍👍🛠️🚜🚀🇷🇺

Bos ung rubber lang ba Ang papalitan Jan pagsira na valve seal Akala ko sate yan

@tractorsmarinemechanic

3 ай бұрын

Valve seal

Sir lanka is

بكم

Boss bakit Yong rotor ng tractor ko mabagal umakyat ano po kaya problema,matagal po kasi umakyat Yong rotor noa

@tractorsmarinemechanic

Жыл бұрын

Check mo sir Ang hydraulic oil at filter palitan kapag Ganon p rin pump n po Ang sira.saan po location nyo?

Ilan po valve clearance nyan idol at parehas lang ba sa makina na 3D84-16A kumatsu

@tractorsmarinemechanic

Жыл бұрын

.25 lang Ang inilagay ko.yong sayo pwd rin para walang gaanong knocking

@freddiepasitenggpawi6084

Жыл бұрын

@@tractorsmarinemechanic salamat idol

Почему попадаєт вода в масло

@tractorsmarinemechanic

Жыл бұрын

Model of your engine?

@sahko_merkylov

Жыл бұрын

@@tractorsmarinemechanic d1102dt

Sir tanung ko lang po .. Ilan ang oil capacity nang Mitsubishi 4dr5 at anung oil ang ginagamit sa ganyang makina ?

@tractorsmarinemechanic

Жыл бұрын

May dipstick nmn po Yan sir sukatin nyo n lang po kc Hindi matandaan Kung Ilan Ang oil capacity nya.sae 40 Ang langis nya.

@roylanggam3111

Жыл бұрын

Salamat po

Bad video doesn’t if tell you the measurements for the rocker and push rods.

@tractorsmarinemechanic

Жыл бұрын

Salamat sa panunood.

Gud day..sir sa Kubota 2402 ano po valve clearance nya? salamat

@tractorsmarinemechanic

Жыл бұрын

Pareho lang po d2..25