- Like - Comment - Subscribe ~ Thanks for watching! 🚧🚧🚧
Жүктеу.....
Пікірлер: 132
@jeagle64 Жыл бұрын
Excellent job. Very efficient. Great training ground for hot mix.
@deej7783 Жыл бұрын
Alsmot went this route. But decided 3 inch reclaim 3 inch asphalt 💯👊 nice finish 👍
@ClutchTFS2 жыл бұрын
Ive done aloot of recycled in my day never seen it laid with a paver looks awesome!
@jamesweir2943 Жыл бұрын
we use a lot of that stuff in Florida and if you lay it down in the heat of the summer and roll it out real good it holds up very nicely.
@Nate-xf6ns2 жыл бұрын
Great work and video!
@rameshshankar1010 Жыл бұрын
Very good clean job 👏
@aaronburford57015 ай бұрын
Great video and content. Liked Shared and Subscribed!
@cbr600rrturbo2 жыл бұрын
Man that looks good
@BigDaddy-dv4wb6 ай бұрын
Great video! I’m going DIY my driveways and save money. These guys want $2-3 per sqft installed. I can get it done myself for much less.
@tylerpittmon79362 жыл бұрын
Looks good! A little cheaper, but still a great alternative!
@notmymonkeynotmycircus8244 Жыл бұрын
Great job.
@GREGHOLUB3 ай бұрын
Looks so good
@Contractorguy Жыл бұрын
Good work
@johnsonbar5022 Жыл бұрын
I seen some contractors use ground up/recycled asphalt that was pulled up from other work sites. Instead of using crushed stone or other aggregate, they use this reclaimed asphalt. Is this an alternate way of putting down a base for new asphalt to sit on? I use to deliver construction materials of all kinds, and every job site that waited to get my turn to unload, I watched dump truck after dump truck, unload stone. My question pertains to residential building, not commercial. Great site by the way.
@douglassmith7515 Жыл бұрын
Looks like a million bucks.
@drewmurphy2796 Жыл бұрын
Where these screened millings or fresh off the mill? After compacted how well do they hold up?
@asphaltcontractors
Жыл бұрын
Fillings are very fresh from the asphalt plant they will never go anywhere as long as they are installed correctly milling's can hold up to 5 to 10 years
@aquajourney9258 Жыл бұрын
Nice video I just had my driveway done just like this. But I haven't put any sealer on it like you did. But I'm curious about putting sealer down later on. My driveway is closed to 600ft long with a hill on part of it.
@asphaltcontractors
Жыл бұрын
Millings are zero maintence but we will never install millings without spraying them. We believe it definetly makes the difference!
@aquajourney9258
Жыл бұрын
@Asphalt Contractors I will definitely get that done then. Thanks
@LGBFJB46
Жыл бұрын
@@asphaltcontractorswhat do you spray them with?
@asphaltcontractors
Жыл бұрын
@@LGBFJB46 Oil-Based Driveway Sealant
@chrissims6289
25 күн бұрын
@@asphaltcontractorsIs that asphalt sealer like cobalt tar your using or is it a tack coat or some kind of rejuvenator?
@Chestickles Жыл бұрын
Haven't use reclaim. They say the best method is to have it ready and spray it before for a 90 degree day, spray the reclaim with diesel and compact it the following day for the do it your DIY. You can use a vibrating compactor.
@rkrueger77
8 ай бұрын
Better to use calcium vs diesel, it reactivates it just like diesel without the smell.
@Cammed300srt8 Жыл бұрын
What kind of sealer do you spray it with ? Or does tack oil work as well ? Please let me know
@asphaltcontractors
Жыл бұрын
We use a oil-based Asphalt Sealer. Aka Gilsonite
@Cammed300srt8
Жыл бұрын
@@asphaltcontractors I see yes I’ve heard of Gilsonite sealer but where can I get it ? I dnt think anyone local to me sells it
@asphaltcontractors
Жыл бұрын
@@Cammed300srt8 You could always order it online just look it up on the internet. Or you might have a supplier near you
@BSTatonka Жыл бұрын
What is recommended maintenance? How long will this last compared to asphalt? Looks amazing. Great job!
@asphaltcontractors
Жыл бұрын
Millings is Zero maintenance because they literally wont go anywhere. All we reccomend is to spray it every 2-3yrs again to help keep oil and tar in millings
@jasonschnapp9624
9 ай бұрын
This doesn't hold up. To go through all this and not just use hot asphalt was absurd.
@melbrad1304
9 ай бұрын
What is that spray?
@andrewcoulter6958 Жыл бұрын
What brand of paver is this? I finally purchased a paver
@asphaltcontractors
Жыл бұрын
This is a Pucket brothers
@WheretheJones2 жыл бұрын
Wow, never seen this done with a paver. How thick was this laid?
@WheretheJones
2 жыл бұрын
Ever lay down road bond / crush and run with a paver?
@asphaltcontractors
2 жыл бұрын
Yes we have and this was layed around 4in. Thick
@halffast77994 ай бұрын
Now spray some diesel or kerosene on it and let the sun work on it. It will tighten up much better. For the price of this, I would have paid the extra for hotmix.
@asphaltcontractors
4 ай бұрын
It is a deisel oil-based sealer mixture.
@kirkshipman88349 ай бұрын
what sealer did you use? and what type sprayer?
@asphaltcontractors
9 ай бұрын
This is a oilbased, Sealer and a Viking pump system
@teamus1756 Жыл бұрын
How would this hold up as a patio
@asphaltcontractors
Жыл бұрын
Not to bad you would just have to install it super thick to help reduce cracking.
@johnregan8093 Жыл бұрын
What kind of Asphalt Spray to use? >I am in North Texas
@asphaltcontractors
Жыл бұрын
Waterbased & oil-based But oil-based we use for asphalt millings
@sherrimullen3396
Жыл бұрын
So new millings you suggest an oil based sealer. Would something like latex-ite driveway sealer work on new millings
@asphaltcontractors
Жыл бұрын
@@sherrimullen3396 Not saying it dosent work. But we have always used oil-based and have never had issues. Oil-based is a penetrating sealer and water based is just a surface sealer.
@davidmondragon60379 ай бұрын
Do you use lot of water to mix it better
@asphaltcontractors
9 ай бұрын
Its a oilbased sealer we apply. So not cut with water.
@adamxie8245 Жыл бұрын
You can see the roller lines
@asphaltcontractors
Жыл бұрын
When millings are first installed they are alot softer than 6month yr. old millings. The surface will always push, When freshly installed.
@julian22arreola Жыл бұрын
For all the work involved and equipment might as well just bought hotmix vs recycled millings.
@asphaltcontractors
Жыл бұрын
True. But its what ever product our customer wants and can afford.
@nettyville8736
Жыл бұрын
Can you tell us what the cost difference is between the two? Roughly, realize it varies regionally.
@dapetik Жыл бұрын
What was sprayed on it at the end?
@asphaltcontractors
Жыл бұрын
Oil-based driveway sealer to help harden the millings and give them a nice look
@juvesoriaiglesiacatolica6633
Жыл бұрын
after the oil is the pervious pavement?
@Refresh54062 жыл бұрын
Roughly how much did this specific job cost the customer?
@asphaltcontractors
2 жыл бұрын
Around 5-6k Millings Are a lot more inexpensive than asphalt
@manweezy209
Жыл бұрын
@@asphaltcontractors including labor?
@asphaltcontractors
Жыл бұрын
@@manweezy209 on this particular job we had no help.
@13hzpodcast882 жыл бұрын
They started playing pinball at god level here 11:41 your welcome
@dauniellemiller91738 ай бұрын
I know each job is different but how much would this job cost?
@asphaltcontractors
8 ай бұрын
in our area this would've run between five or 7000
@FRONTLINEAUTO400
8 ай бұрын
Are you guys in Kansas City?
@FRONTLINEAUTO400
8 ай бұрын
@@asphaltcontractorsare you guys in Kansas City?
@asphaltcontractors
8 ай бұрын
@@FRONTLINEAUTO400 P.A
@offgridas Жыл бұрын
What is a truck load of millings worth?
@asphaltcontractors
Жыл бұрын
For us about 400$. Hauling not included
@offgridas
Жыл бұрын
@@asphaltcontractors how many truck loads did this job take?
@asphaltcontractors
Жыл бұрын
@@offgridas I want to say around 4 20ton loads. We usually lay around 3-4in. Compacted.
@cd1168 Жыл бұрын
Where can you buy the oil based sealer?
@asphaltcontractors
Жыл бұрын
Sealer Supplier
@cd1168
Жыл бұрын
@@asphaltcontractors great answer
@bhadz100 Жыл бұрын
Can this be put over beat up asphalt?
@asphaltcontractors
Жыл бұрын
Yes Old Asphalt acts as a good base.
@knndy77 Жыл бұрын
How does the driveway look a year later
@asphaltcontractors
Жыл бұрын
Posting a New Short on that!
@asphaltcontractors
Жыл бұрын
Also i do have a picture if you would provide your email i could send you a picture!
@germanromerosoto1844 Жыл бұрын
What did you spray at the end ?
@asphaltcontractors
Жыл бұрын
A deisel and oil-based sealer mixture to help harden the millings.
@germanromerosoto1844
Жыл бұрын
@@asphaltcontractors ok cool does the product come as one , or does it need to Be mixed ?
@asphaltcontractors
Жыл бұрын
@@germanromerosoto1844 We self mix it ourselfes
@stephendean9083
Жыл бұрын
@@asphaltcontractors is there a specific mix you make or can it be bought from the store?
@asphaltcontractors
Жыл бұрын
@@stephendean9083 No we make our own mix we use deisel fuel and oil based asphalt sealer.
@geofferywhedbee90472 жыл бұрын
What if you let someone put "asphalt" on your long driveway only to find out after that it was only millings? Can I do anything to make it usable and to where it won't track into the garage or house?
@asphaltcontractors
2 жыл бұрын
I mean that sucks. But what we do is compact them with a asphalt roller like you do asphalt and we apply the harder its a mix of Deisel fuel and asphalt oil based sealer. it helps harden them for less tracking but we have never really had issues with tracking in the past so not to sure.
@ClutchTFS
2 жыл бұрын
Did they tell ya itd be hot ? If so, sounds like a gypsy did it
@asphaltcontractors
2 жыл бұрын
@@ClutchTFS We installed it our selfves we explain that it is recycled asphalt. Not hot asphalt.
@aceboogiect
Жыл бұрын
@@asphaltcontractors what’s the ratio for the mix? Looking to do this idea for small parking lot
@simd510 Жыл бұрын
How much cheaper is this than hot asphalt?
@asphaltcontractors
Жыл бұрын
Asphalt atm is 85$ a ton. Millings is around 15$
@wellendowedstudios Жыл бұрын
Maybe an OCD but that guy on the roller did a shitty job on the far end corner, I can see the raised lines yet, he should have rolled them down they stick out like a soar thumb
@asphaltcontractors
Жыл бұрын
Everything gets rolled twice which was not shown in the video. Video only showed rolled once.
@MarcusAureliusLLCMetalFab Жыл бұрын
Hammond indiana I put asphalt millings on my yard but inspector wants me to get an environmental impact study to test the millings are safe. Anyone had idea if millings are dangerous or I have a inspector that is just talk bs.
@fermiticus4034
Жыл бұрын
I'd bet his brother owns an "environmental impact study" company!!!
@asphaltcontractors
Жыл бұрын
I know for a fact, asphalt millings are environmental friendly
@Orefamilylawncare
Жыл бұрын
Sounds like BS.
@RD-ii7ly
Жыл бұрын
It is recycled asphalt. It is asphalt that has been milled off an existing road and milled again and/or screened for size consistency. No real difference from the roads towns, counties, states, and the federal government have laid all across the country.
@davidanderson1451
Жыл бұрын
some agency's around the US are looking at millings from an environmental stand point now. Do they pollute ground water? Do they pollute the ground? We have to protect all catch basins with witch hats when we mill. The water run off from our milling piles at our plants has to be collected as sewer waste, storm waste. Get ready for it, because it is coming. We have one plant where the jurisdiction wont even let us use RAP in our plant due to environmental concerns
@Aaronferguson312 жыл бұрын
What's it cost per sq ft installed?
@asphaltcontractors
2 жыл бұрын
Usually dont price by sqft. Price by what the job consists of.
@goinbananas7606
2 жыл бұрын
ive done it for years it depends on the base being applied to, but american 50/60 cents a square foot is a really good price if its laid at 4inches compacted with 3tonnes or more.
@goinbananas7606
2 жыл бұрын
also recycled will have pebbles, like rock debris that comes up, what i genuinely liked to do was roll it and let the customers drive on it but alternate there driving postitions for equal compaction as they continue to drive, 1 year down the line it will look rough but it will be durable so a sealcoat would definitely help make it look better because they do look fade after awhile
@goinbananas7606
2 жыл бұрын
also dont fall into the belief that this is going to be looking like that forever, i have done a job though which requires different aggregate then he had that does actually replicate asphalt
@pmg2120
5 ай бұрын
@@goinbananas7606 WTF? Why are you working for nothing? It’s people like you that ruin businesses.
@trevoroneill8131 Жыл бұрын
How much did this cost?
@asphaltcontractors
Жыл бұрын
around 6k
@trevoroneill8131
Жыл бұрын
@@asphaltcontractors what if you overlayed a gravel driveway how much does that cost
@asphaltcontractors
Жыл бұрын
@@trevoroneill8131 All depends on the driveway and what needs to be done
@simd510
Жыл бұрын
@@asphaltcontractors how much would this same job have been if it was hot mix?
@asphaltcontractors
Жыл бұрын
@@simd510 Between 10-15k
@curtpyro15182 жыл бұрын
I noticed they miss some spots. I know if I was a contractor I would make sure that everything gets smoothed out and everything would have to be as level as possible.
@asphaltcontractors
2 жыл бұрын
It's asphalt millings some contractors dont even roll in the product or spray a hardener. this stuff gets harder on its own it doesn't need help. But Rolling it in and spraying a Hardner helps it out a bunch
@m.martinjosephs7180
2 жыл бұрын
@@asphaltcontractors What is the hardener you use? and how do i get it? I am in the Atlanta, GA area.
@asphaltcontractors
2 жыл бұрын
@@m.martinjosephs7180 Its deisel fuel and oil based asphalt sealer.
@goinbananas7606
2 жыл бұрын
@@asphaltcontractors bro i got a way better recipe ;D diesel fuel actually degrades asphalt btw not hating we all have our opinions
@goinbananas7606
2 жыл бұрын
also if your rollers rolled like that with hot asphalt your stuff would look terrible :/ i seen horrible lines thru that on recycled, i get it will pack during people driving on it but cmon...
Пікірлер: 132
Excellent job. Very efficient. Great training ground for hot mix.
Alsmot went this route. But decided 3 inch reclaim 3 inch asphalt 💯👊 nice finish 👍
Ive done aloot of recycled in my day never seen it laid with a paver looks awesome!
we use a lot of that stuff in Florida and if you lay it down in the heat of the summer and roll it out real good it holds up very nicely.
Great work and video!
Very good clean job 👏
Great video and content. Liked Shared and Subscribed!
Man that looks good
Great video! I’m going DIY my driveways and save money. These guys want $2-3 per sqft installed. I can get it done myself for much less.
Looks good! A little cheaper, but still a great alternative!
Great job.
Looks so good
Good work
I seen some contractors use ground up/recycled asphalt that was pulled up from other work sites. Instead of using crushed stone or other aggregate, they use this reclaimed asphalt. Is this an alternate way of putting down a base for new asphalt to sit on? I use to deliver construction materials of all kinds, and every job site that waited to get my turn to unload, I watched dump truck after dump truck, unload stone. My question pertains to residential building, not commercial. Great site by the way.
Looks like a million bucks.
Where these screened millings or fresh off the mill? After compacted how well do they hold up?
@asphaltcontractors
Жыл бұрын
Fillings are very fresh from the asphalt plant they will never go anywhere as long as they are installed correctly milling's can hold up to 5 to 10 years
Nice video I just had my driveway done just like this. But I haven't put any sealer on it like you did. But I'm curious about putting sealer down later on. My driveway is closed to 600ft long with a hill on part of it.
@asphaltcontractors
Жыл бұрын
Millings are zero maintence but we will never install millings without spraying them. We believe it definetly makes the difference!
@aquajourney9258
Жыл бұрын
@Asphalt Contractors I will definitely get that done then. Thanks
@LGBFJB46
Жыл бұрын
@@asphaltcontractorswhat do you spray them with?
@asphaltcontractors
Жыл бұрын
@@LGBFJB46 Oil-Based Driveway Sealant
@chrissims6289
25 күн бұрын
@@asphaltcontractorsIs that asphalt sealer like cobalt tar your using or is it a tack coat or some kind of rejuvenator?
Haven't use reclaim. They say the best method is to have it ready and spray it before for a 90 degree day, spray the reclaim with diesel and compact it the following day for the do it your DIY. You can use a vibrating compactor.
@rkrueger77
8 ай бұрын
Better to use calcium vs diesel, it reactivates it just like diesel without the smell.
What kind of sealer do you spray it with ? Or does tack oil work as well ? Please let me know
@asphaltcontractors
Жыл бұрын
We use a oil-based Asphalt Sealer. Aka Gilsonite
@Cammed300srt8
Жыл бұрын
@@asphaltcontractors I see yes I’ve heard of Gilsonite sealer but where can I get it ? I dnt think anyone local to me sells it
@asphaltcontractors
Жыл бұрын
@@Cammed300srt8 You could always order it online just look it up on the internet. Or you might have a supplier near you
What is recommended maintenance? How long will this last compared to asphalt? Looks amazing. Great job!
@asphaltcontractors
Жыл бұрын
Millings is Zero maintenance because they literally wont go anywhere. All we reccomend is to spray it every 2-3yrs again to help keep oil and tar in millings
@jasonschnapp9624
9 ай бұрын
This doesn't hold up. To go through all this and not just use hot asphalt was absurd.
@melbrad1304
9 ай бұрын
What is that spray?
What brand of paver is this? I finally purchased a paver
@asphaltcontractors
Жыл бұрын
This is a Pucket brothers
Wow, never seen this done with a paver. How thick was this laid?
@WheretheJones
2 жыл бұрын
Ever lay down road bond / crush and run with a paver?
@asphaltcontractors
2 жыл бұрын
Yes we have and this was layed around 4in. Thick
Now spray some diesel or kerosene on it and let the sun work on it. It will tighten up much better. For the price of this, I would have paid the extra for hotmix.
@asphaltcontractors
4 ай бұрын
It is a deisel oil-based sealer mixture.
what sealer did you use? and what type sprayer?
@asphaltcontractors
9 ай бұрын
This is a oilbased, Sealer and a Viking pump system
How would this hold up as a patio
@asphaltcontractors
Жыл бұрын
Not to bad you would just have to install it super thick to help reduce cracking.
What kind of Asphalt Spray to use? >I am in North Texas
@asphaltcontractors
Жыл бұрын
Waterbased & oil-based But oil-based we use for asphalt millings
@sherrimullen3396
Жыл бұрын
So new millings you suggest an oil based sealer. Would something like latex-ite driveway sealer work on new millings
@asphaltcontractors
Жыл бұрын
@@sherrimullen3396 Not saying it dosent work. But we have always used oil-based and have never had issues. Oil-based is a penetrating sealer and water based is just a surface sealer.
Do you use lot of water to mix it better
@asphaltcontractors
9 ай бұрын
Its a oilbased sealer we apply. So not cut with water.
You can see the roller lines
@asphaltcontractors
Жыл бұрын
When millings are first installed they are alot softer than 6month yr. old millings. The surface will always push, When freshly installed.
For all the work involved and equipment might as well just bought hotmix vs recycled millings.
@asphaltcontractors
Жыл бұрын
True. But its what ever product our customer wants and can afford.
@nettyville8736
Жыл бұрын
Can you tell us what the cost difference is between the two? Roughly, realize it varies regionally.
What was sprayed on it at the end?
@asphaltcontractors
Жыл бұрын
Oil-based driveway sealer to help harden the millings and give them a nice look
@juvesoriaiglesiacatolica6633
Жыл бұрын
after the oil is the pervious pavement?
Roughly how much did this specific job cost the customer?
@asphaltcontractors
2 жыл бұрын
Around 5-6k Millings Are a lot more inexpensive than asphalt
@manweezy209
Жыл бұрын
@@asphaltcontractors including labor?
@asphaltcontractors
Жыл бұрын
@@manweezy209 on this particular job we had no help.
They started playing pinball at god level here 11:41 your welcome
I know each job is different but how much would this job cost?
@asphaltcontractors
8 ай бұрын
in our area this would've run between five or 7000
@FRONTLINEAUTO400
8 ай бұрын
Are you guys in Kansas City?
@FRONTLINEAUTO400
8 ай бұрын
@@asphaltcontractorsare you guys in Kansas City?
@asphaltcontractors
8 ай бұрын
@@FRONTLINEAUTO400 P.A
What is a truck load of millings worth?
@asphaltcontractors
Жыл бұрын
For us about 400$. Hauling not included
@offgridas
Жыл бұрын
@@asphaltcontractors how many truck loads did this job take?
@asphaltcontractors
Жыл бұрын
@@offgridas I want to say around 4 20ton loads. We usually lay around 3-4in. Compacted.
Where can you buy the oil based sealer?
@asphaltcontractors
Жыл бұрын
Sealer Supplier
@cd1168
Жыл бұрын
@@asphaltcontractors great answer
Can this be put over beat up asphalt?
@asphaltcontractors
Жыл бұрын
Yes Old Asphalt acts as a good base.
How does the driveway look a year later
@asphaltcontractors
Жыл бұрын
Posting a New Short on that!
@asphaltcontractors
Жыл бұрын
Also i do have a picture if you would provide your email i could send you a picture!
What did you spray at the end ?
@asphaltcontractors
Жыл бұрын
A deisel and oil-based sealer mixture to help harden the millings.
@germanromerosoto1844
Жыл бұрын
@@asphaltcontractors ok cool does the product come as one , or does it need to Be mixed ?
@asphaltcontractors
Жыл бұрын
@@germanromerosoto1844 We self mix it ourselfes
@stephendean9083
Жыл бұрын
@@asphaltcontractors is there a specific mix you make or can it be bought from the store?
@asphaltcontractors
Жыл бұрын
@@stephendean9083 No we make our own mix we use deisel fuel and oil based asphalt sealer.
What if you let someone put "asphalt" on your long driveway only to find out after that it was only millings? Can I do anything to make it usable and to where it won't track into the garage or house?
@asphaltcontractors
2 жыл бұрын
I mean that sucks. But what we do is compact them with a asphalt roller like you do asphalt and we apply the harder its a mix of Deisel fuel and asphalt oil based sealer. it helps harden them for less tracking but we have never really had issues with tracking in the past so not to sure.
@ClutchTFS
2 жыл бұрын
Did they tell ya itd be hot ? If so, sounds like a gypsy did it
@asphaltcontractors
2 жыл бұрын
@@ClutchTFS We installed it our selfves we explain that it is recycled asphalt. Not hot asphalt.
@aceboogiect
Жыл бұрын
@@asphaltcontractors what’s the ratio for the mix? Looking to do this idea for small parking lot
How much cheaper is this than hot asphalt?
@asphaltcontractors
Жыл бұрын
Asphalt atm is 85$ a ton. Millings is around 15$
Maybe an OCD but that guy on the roller did a shitty job on the far end corner, I can see the raised lines yet, he should have rolled them down they stick out like a soar thumb
@asphaltcontractors
Жыл бұрын
Everything gets rolled twice which was not shown in the video. Video only showed rolled once.
Hammond indiana I put asphalt millings on my yard but inspector wants me to get an environmental impact study to test the millings are safe. Anyone had idea if millings are dangerous or I have a inspector that is just talk bs.
@fermiticus4034
Жыл бұрын
I'd bet his brother owns an "environmental impact study" company!!!
@asphaltcontractors
Жыл бұрын
I know for a fact, asphalt millings are environmental friendly
@Orefamilylawncare
Жыл бұрын
Sounds like BS.
@RD-ii7ly
Жыл бұрын
It is recycled asphalt. It is asphalt that has been milled off an existing road and milled again and/or screened for size consistency. No real difference from the roads towns, counties, states, and the federal government have laid all across the country.
@davidanderson1451
Жыл бұрын
some agency's around the US are looking at millings from an environmental stand point now. Do they pollute ground water? Do they pollute the ground? We have to protect all catch basins with witch hats when we mill. The water run off from our milling piles at our plants has to be collected as sewer waste, storm waste. Get ready for it, because it is coming. We have one plant where the jurisdiction wont even let us use RAP in our plant due to environmental concerns
What's it cost per sq ft installed?
@asphaltcontractors
2 жыл бұрын
Usually dont price by sqft. Price by what the job consists of.
@goinbananas7606
2 жыл бұрын
ive done it for years it depends on the base being applied to, but american 50/60 cents a square foot is a really good price if its laid at 4inches compacted with 3tonnes or more.
@goinbananas7606
2 жыл бұрын
also recycled will have pebbles, like rock debris that comes up, what i genuinely liked to do was roll it and let the customers drive on it but alternate there driving postitions for equal compaction as they continue to drive, 1 year down the line it will look rough but it will be durable so a sealcoat would definitely help make it look better because they do look fade after awhile
@goinbananas7606
2 жыл бұрын
also dont fall into the belief that this is going to be looking like that forever, i have done a job though which requires different aggregate then he had that does actually replicate asphalt
@pmg2120
5 ай бұрын
@@goinbananas7606 WTF? Why are you working for nothing? It’s people like you that ruin businesses.
How much did this cost?
@asphaltcontractors
Жыл бұрын
around 6k
@trevoroneill8131
Жыл бұрын
@@asphaltcontractors what if you overlayed a gravel driveway how much does that cost
@asphaltcontractors
Жыл бұрын
@@trevoroneill8131 All depends on the driveway and what needs to be done
@simd510
Жыл бұрын
@@asphaltcontractors how much would this same job have been if it was hot mix?
@asphaltcontractors
Жыл бұрын
@@simd510 Between 10-15k
I noticed they miss some spots. I know if I was a contractor I would make sure that everything gets smoothed out and everything would have to be as level as possible.
@asphaltcontractors
2 жыл бұрын
It's asphalt millings some contractors dont even roll in the product or spray a hardener. this stuff gets harder on its own it doesn't need help. But Rolling it in and spraying a Hardner helps it out a bunch
@m.martinjosephs7180
2 жыл бұрын
@@asphaltcontractors What is the hardener you use? and how do i get it? I am in the Atlanta, GA area.
@asphaltcontractors
2 жыл бұрын
@@m.martinjosephs7180 Its deisel fuel and oil based asphalt sealer.
@goinbananas7606
2 жыл бұрын
@@asphaltcontractors bro i got a way better recipe ;D diesel fuel actually degrades asphalt btw not hating we all have our opinions
@goinbananas7606
2 жыл бұрын
also if your rollers rolled like that with hot asphalt your stuff would look terrible :/ i seen horrible lines thru that on recycled, i get it will pack during people driving on it but cmon...