Record Power Coronet Envoy Lathe vs Coronet Herald , A Review of Each Lathes Features EthAnswers

Пікірлер: 33

  • @leslamb9190
    @leslamb91903 жыл бұрын

    Not covered in this video but from reading the tech spec I understand that there are very important differences in the two motors. The Herald is DC where speed is controlled by variable resistors while the Envoy/Regent are AC and speed is controlled by a variable frequency module. AC tends to be preferred as there is minimal impact on torque at different speeds.

  • @raydriver7300
    @raydriver7300 Жыл бұрын

    What a helpful video. I’ve just replaced my Herald with a Regent after much agonising (I’m in the UK) and have spent the last week redoing my shed to accommodate it as my Herald was bench mounted. Looking forward to using it. And, yes, it is very quiet. Thank you for sharing 🌞

  • @nobby21165

    @nobby21165

    Жыл бұрын

    Now doing exactly the same thing! Bench is now kindling, just got to wait for delivery from Yandles! Have fun!

  • @icespeckledhens
    @icespeckledhens4 жыл бұрын

    The spindle lock, that you mentioned, is only for indexing not for taking chucks on and off. Good review. personally, if I was choosing I would either go for the Herald, for pens, small turnings and small bowls and you would then want the bed extension for any bowls or go for the Regent for large bowls etc. Thanks James

  • @andrewhall6880
    @andrewhall68803 жыл бұрын

    Great presentation Ethan

  • @StockroomSupply

    @StockroomSupply

    3 жыл бұрын

    Thanks Andrew. I enjoy you presentations as well!

  • @hassanal-mosawi6049
    @hassanal-mosawi60494 жыл бұрын

    Thanks for sharing that, well said!

  • @tomalealso
    @tomalealso2 ай бұрын

    I have had my Herald for a few months and I absolutely love it, the only thing that is just a little annoying is the size of the hand wheel, its a little small and it would be nice to have the to have moveable controls, it has not been an issue yet but if I do some bigger bowls I can see it becoming an issue. yes I know they make a magnetic stop switch but all that does for you is add a little safety but it does nothing in your everyday use of the machine. frankly it is a little condescending. I really can't complain much because for the size it is way better than anything else in is size.

  • @I-Love-Taylor-Swift
    @I-Love-Taylor-Swift3 жыл бұрын

    That Herald is a lovely machine. But the Envoy is even better!! I would love one, even though I have no use for one, haha!!

  • @briardsnz
    @briardsnz4 жыл бұрын

    Hi, thanks for good comparison and for the Envoy/Regent video too. Couple of questions. Do the Envoy/Regent speed controls operate same as Herald with pre- selection of rpm? Or just display actual spindle rpm while running? Where is the indexing view window on Envoy/Regent - haven't managed to see it in any of the photos or video clip angles. Thanks.

  • @CTHOROS
    @CTHOROS3 жыл бұрын

    Thanks for the comparison and the information. Do you know if Envoy comes with 230V motor for Europe;

  • @richardhawkins2647
    @richardhawkins26474 жыл бұрын

    Want one!!! The Envoy is currently my dream lathe. I need to find some serious pennies though!

  • @rev.twilson7300

    @rev.twilson7300

    2 жыл бұрын

    I think you made a good choice. I ordered one yesterday. It's going to be a sweet machine. Me and my wife are both left handers.

  • @zalexwood5904
    @zalexwood59044 жыл бұрын

    well! very nice video! i bought the coronet herald today!

  • @StockroomSupply

    @StockroomSupply

    4 жыл бұрын

    Awesome! You will enjoy it!!

  • @zalexwood5904

    @zalexwood5904

    4 жыл бұрын

    @@StockroomSupply Thanks so much!

  • @JohnShumate-el4iu
    @JohnShumate-el4iu10 ай бұрын

    Why do their upper models have a low speed of 200-250 while the Herald goes down to 150 I believe?

  • @keithtregidgo5639
    @keithtregidgo56394 жыл бұрын

    Do you have a review on a status twisted f u 180

  • @trynforpar
    @trynforpar8 ай бұрын

    Does the Record Envoy make a mobility kit to move the lathe around

  • @DavidR8
    @DavidR8 Жыл бұрын

    Thanks Ethan really appreciate the walkthrough on the Record lathes. I have a Rikon 70-220VSR and am looking to upgrade in the future. The Regent is appealing because of it's small footprint but wondering if it's different enough to be worth it or is the Envoy the logical upgrade?

  • @shaunhayward

    @shaunhayward

    Жыл бұрын

    I'm in the same boat as you. I have the 70-220 and have long thought about a bigger lathe. Both seem like substantial upgrades to the 70-200. Both can take bed extensions. Both swivel for turning BIG things. My thinking is, though, that the envoy is only 17% more than the Regent. I think the biggest difference is the ubiquity of 110v vs the extra HP of the 220v Envoy.

  • @richardkarch3726
    @richardkarch37262 ай бұрын

    How do you align the drive points on the Hareld?

  • @ian_wood-1gdtrn
    @ian_wood-1gdtrn11 ай бұрын

    Brilliant video thank you.. i appreciate im coming to the party late but really looking forward to getting my next lathe - can anyone help me with what the total length of the Envoy with outrigger and extension is?

  • @stevebarker1302

    @stevebarker1302

    7 ай бұрын

    the lathe bed is 1055mm with the bed extension its 1580mm, not sure about the out rigger, it will add at a guess another 150mm?

  • @ahdigger
    @ahdigger5 ай бұрын

    Hi.I am really interested in purchasing the Coronet Regent 18" x 24". I saw a review on KZread that when you press the emergency stop it doesn't stop the lathe right away but it takes some time until it stops. Do you have an idea if they fix this issue? Thank you.

  • @humbleak4770
    @humbleak4770 Жыл бұрын

    I am getting ready to order a Helard...my understanding is they made the tailstock self eject and the screw integrated...can you confirm?

  • @kerstin4516

    @kerstin4516

    Жыл бұрын

    Hi, Humble. Yes, the Herald is self ejecting meanwhile. I bought mine about half a year ago. Happy turning.

  • @johndunbar8326
    @johndunbar83264 жыл бұрын

    Whatprice is The Envoy

  • @user-uu6px9yh5o
    @user-uu6px9yh5o8 ай бұрын

    Is there a number that I can call I'm from Kansas and I like to have more information on this I'm new on this

  • @mikethompson9745
    @mikethompson97452 жыл бұрын

    i'd like to hear your videos, so far all your audio is poor

  • @raydriver7300
    @raydriver7300 Жыл бұрын

    To nobby21165. I bought mine from Yandles but I drove an 8 hour round trip and picked it up myself 🌞

Келесі