Rear Brake Pads and Rotors Replacement on Range Rover L405 and Sport L494 in Step by Step Guide
Автокөліктер мен көлік құралдары
Hi! This is a step by step guide on how to replace rear brake pads and rotors (discs) on 2013-2021 Range Rover L405 and Range Rover Sport L494
Looking for a European car specialist in Southern California? I can help!
Click the link below to get a quote now!👇
app.shopmonkey.io/quote-reque...
Instagram:
/ alex.fixty
Torque specs for wheel bolts - 103 ft-lbs
Front Brake Pads and Rotors replacement:
• Front Brake Pads and R...
Parts and tools:
CALIPER REWIND TOOL:
amzn.to/3UQfuX5
OEM GENUINE REAR BRAKE PAD SET:
amzn.to/3eFLARW
GENUINE LAND ROVER REAR BRAKE PAD SENSOR:
amzn.to/2R2LqvR
TRW PRO REAR BRAKE PADS:
amzn.to/3nnvbam
REAR BRAKE PAD WEAR SENSOR:
amzn.to/3HAnVlk
REAR OE ROTORS:
amzn.to/3TLA7oK
The tools you need:
CAR JACK
BRAKE CALIPER REWIND TOOL
HAMMER
SCREWDRIVER or PICK TOOL
3/8in SOCKET WRENCH
1/2in BREAKER BAR
15mm WRENCH
PICK TOOL
METAL BRUSH
13mm T50 3/8in SOCKETS
22mm 1/2in SOCKETS
JACK STANDS
BRAKE CLEANER
BRAKE & CALIPER GREASE
Any help would be greatly appreciated🙏 www.paypal.com/donate?busines...
Disclaimer:
Due to factors beyond the control of Land Rover Tech, I cannot guarantee against improper use or unauthorized modifications of this information. Land Rover Tech assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. Land Rover Tech recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of Land Rover Tech, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Land Rover Tech.
#landrover #rangerover #l405 #L494
Пікірлер: 131
Hi! I provide mobile car repairs for European vehicles in Southern California. Request a quote here👇 app.shopmonkey.io/quote-request/e4c56803325fda668f1050eca12fba84?noExternalScripts=1
I was scared to do this but now I am not. Alex you're a lifesaver and we appreciate your channel. Guys/Gals don't be scared to donate to this fella and subscribe.
You are a legend my friend. The caliper piston recompression had me the most worried, but it seems to be straight compression, no screw winding needed. Already have the tools so I'm good to go. Thanks so much.
Hi Alex thank you very much for your videos. Today I replaced my break pads on the rear of my Range Rover L405. Without your help I would have gone and paid a lot of money to land Rover. Keep up the good work. !!!
awesome job Alex. very helpful. thank you!
Love your videos... Well done!
I want to change my Velar rear breaks. Your video helped me a lot. Cheers.
@lolorenzo3762
2 жыл бұрын
Are they exactly the same?
Great job Alex. Your videos are very informative. In addition to changing the brakes, I'm about to flush the differentials, transfer case, and the ZF transmission on my 2015 RR Sport if you're looking for new DIY content to help others like me.
@Alexfixty
3 жыл бұрын
Thank you! Will do someday!
You're awesome, Lemon thanks you. I watch everything you make))) Cheers.
@Alexfixty
3 жыл бұрын
Thank you 🙏🙏🙏
I have one comment regarding the lubrication of the clips. The grease goes on between the carrier and the clip. The purpose of the grease is not to minimise friction between the brakepad and the clip, but to prevent rust from forming behind the clip. Rust has a bigger volume than iron, so if rust forms, it will squeeze the clip towards the pad and make it bind up. Here in Sweden, with salty roads, I see this happen all the time.
@davidwynne3289
4 ай бұрын
Excellent, informative video. 👍
Very helpful my friend.
Love your video's! Do you have : how to change the rear hub - bearing ?
Thanks! Super useful. This is the same procedure on Discovery 5.
@Alexfixty
11 ай бұрын
🙏
My brother, you're doing God's work!!!👌🏾✊🏾🙌🏾 You've saved me $100's ! I appreciate the tutorial!
@Alexfixty
Жыл бұрын
🖖🖖🖖
I have benefited from this wonderful
Big help thanks.
Hey can you do a belt replacement video? getting a L560, just curious if its an easy enough home job. Thanks in advance.
I hope my comments will prevent anyone else from making my mistake. The only thing I believe I did differently from your video was I couldn't enter maintenance mode. Therefore, I started the car and had it running to disengage the e brake. This allowed me to remove the caliper, but I couldn't compress the brake piston. A costly mistake. Thank you again for the video. Keep up the great work.
@Alexfixty
Жыл бұрын
Sorry to hear that!
Great Content.
Txs. Great video 👌
A thanks for sharing saved Me some money
Excellent video mate! 😊
@Alexfixty
4 ай бұрын
Thanks a lot!
احسنت عمل رائع ومعلومات جييده شكرأ
Nice vid... good job
There is no such thing as simply disconnect the brake sensor at the chasis im finding out. I cut the tab off the middle sensor so I could access it enough to pull the tab up to disconnect the sensor wire there. Otherwise rear brakes r easy. Turing the brake on and off was diff. Finally found someone online who described it so it worked.
Very well explained, thank you.
@Alexfixty
2 ай бұрын
Glad it was helpful!
Здорово! Очень аккуратно и грамотно
Awesome Video Thank You for sharing this Great information
@Alexfixty
8 ай бұрын
✊
Replace the plastic cap lug nuts. Took me 20 minutes to do the brakes front and back. Took me two hours and four different sockets to get the Lugnuts off. One piece steel ones on Amazon for 39.99
Mulțumim !sfaturi foarte utile😊
@Alexfixty
Жыл бұрын
🙌🙌🙌
One thing you should add in your videos... torque specs whenever you tighten a bolt! For those of us wanting to stick with the manufacturing recommendations... thx
@Alexfixty
7 ай бұрын
💯
Good one bro
great man thank you
Your the best 👌🏾👌🏾👌🏾
Is this the same procedure in putting a Range Rover Velar parking brake into MAINTENANCE Mode?
Thank you for the great information. I ll do my car tomorrow
@Alexfixty
3 ай бұрын
Glad it helped
well in thank you for this 🍻
@Alexfixty
Ай бұрын
🤙🤙🤙
Good Day! Pls I loosed and removed the two back brake callipers to compress them as the new pads wasn't entering, after fixing them back and bleeding, the brake pedal goes flat at first and comes a bit hard after several pumping but still goes flat when left for few minutes, had tried several means of bleeding, even changed the brake master and ABS Module but still having same brake failure. Kindly help urgently. Sorry it's a Range Rover 2014 Autobiography and all the jobs where done without me activating the maintenance service mode or can it be the cause?
I have 2017 range rover sport, I tried to put into service mode, it doesn't go, please advise. Thank you
Time and money safer Thank You
Thank you it's great job I changed my barke bad last month and I did not do service mood shall I do it?
@Alexfixty
3 жыл бұрын
Hi! Most likely it's been adjusted automatically.. But you can do it just in case👌
god you save my life bro..👍👍👍
Do you normally grease the caliper slide pin inside the one with the rubber accordian - the one you take off with the 13 and 17 mm
Great video!.. Are you going to do a video for the front? Thanks
@Alexfixty
3 жыл бұрын
Here is the front kzread.info/dash/bejne/gn98pKSEh7WZcdY.html
Should you replace the bolts or use thread-lock blue? Which is better?
Thank u and well done
@Alexfixty
9 ай бұрын
✊✊✊
Good job
@Alexfixty
2 жыл бұрын
Thanks
The way you put the car in Brake Service Mode does it work for a 2017 Range Rover Evoque HSE ?.......... And when you put the car in brake service mode can you turn the car off or do you have to leave it in accessory on ?
My range rover 2016 have brake fault and I find out my rear right caliper is stuck I change put new bu how I reset this brake fault thank you
Will it be same for range rover vogue SE ?
Thanks Boss
Gracias
Hi sir after brake job my front brake make clunk noise when hit the brake hard
To compress the piston could you not just use a c clamp?
YO broski thank you so much. im broke with an LR4, saved me tons of $$$ doing transmission anytime soon? lmao
شكرأ الك هل جميع السيارات هي نفس الطريقه ارجو الرد صديقي
ALEX THA GOAT SHOWING THIS! my guy just got it buttoned up! Everything smooth brand new ceramic pads and rotors for 350$ x4
@Alexfixty
10 ай бұрын
Nice!
@startingtech3900
10 ай бұрын
@@Alexfixty alex where is go fund me for your new l405 rover so you can make more RR videos bro
@Alexfixty
9 ай бұрын
Here Fixty.com 😂
Thanks a lot for that video, very informative. Doing this now in the car shop Looks like you're from Russia 😂
is bleeding the breaks required?
How do you put a 2018 Velar into electric power brake maintenance mode this mode here did not work for my velar? Does anyone know?
@nicholasbryant4652
2 жыл бұрын
We’re you able to find out how to do this
Hi. Do we need new brake sensor every time change new brake pads. Thanks
@Alexfixty
3 жыл бұрын
Hi! If the sensor is good and there is no brake light on dashboard, no need to replace it
Well made video. I am considering buying a 2013 HSE Sport and would like some tips. Do you have an email I can reach you at?
Hello, when changes front/rear pads and rotors is there a need to do a break? Thanks
@Alexfixty
3 жыл бұрын
After you replaced brake pads, pump the brake pedal till it gets hard
Do you always have to replace rotors when replacing the pads? My brake light won’t go off ... any advice?
@rhkavli
Жыл бұрын
No. But if you replace the rotors, always use new pads with them. Rotor replacement is done if they are severely blue, due to a binding caliper, severe rust, grooves in the surface, or minimum thickness being reached. Then both sides on the same "axle" should be replaced, regardless of the condition on the other side. This is to maintain a good brake balance. If the warning indicator for brake pad wear is lit, you have either consumed the wear sensor, so it has to be replaced, or you have a break in the sensing circuit.
احسنت عمل جيد
Remember to properly hang the caliper so that the rubber brake hose won't mess up.
@Alexfixty
Жыл бұрын
💯
@tiffanygentry6004
9 ай бұрын
@rightorwrong8951 Can You explain further! you got me thinking like damn did I hang it right?? -Jay Howard But Thank you Alex Your a Life saver bro literally saved me $2000 knew they was trynna play me when they said $770 for the just the rear pads and $790 for the the front. Your the GOAT!!
Do you have to replace the sensor when putting new pads in or can you use the old one?
@Alexfixty
Жыл бұрын
If it’s not damaged you can leave the old one
How to reset your engine light on your Land Rover
You should invest in a torque wrench. Why did you not grease the guide pins?
is this the same procedure for a 20' velar?
@Alexfixty
Жыл бұрын
Not sure
Alex my rear piston is solid as a mofo. It’s stuck won’t compress what do I do
@startingtech3900
10 ай бұрын
FOR ALL THOSE WONDERING DO WHAT ALEX SAID PUT IN SERVICE MODE IN BEGINNING
Hey Alex. One more question if you don't mind. I received my new caliper. I'm reinstalling the old motor for the e-brake on the new caliper. The motor is currently unplugged and on the bench. The car is currently in maintenance mode. Is the e-brake motor required to be reset into a maintenance mode position before installing it on the new caliper? Currently, I don't know what position the motor is in. If so, do you have a recommendation? Thanks in advance!
@Alexfixty
Жыл бұрын
When you set it into maintenance mode you can hear how the they unwind into 0 position. Not sure if you need to do something with it.
@culpyy
Жыл бұрын
@@Alexfixty I understand. Thanks again Alex.
Is it just compressing the brake piston or must you engage the cutouts on the piston and then turn and compress. It also looks as if you are turning piston to the left instead of right. On my 2016..you have to turn piston to right to compress it....Very unclear.
would this apply to a 2013 LR4?
@Alexfixty
Жыл бұрын
Not sure tbh 😕
Awesome video...where are you purchasing the pads rotors and sensors?
@freddygarrett
3 жыл бұрын
Thanks I went to the dealership they told me 1,400 for the front an 1,200 for rear I was like what that crazy ordered all from rock 🪨 auto rotors and pads 300
@freddygarrett
3 жыл бұрын
New oner of a L405 anything’s should look out for
@denallizx10
3 жыл бұрын
@@freddygarrett nothing I've experienced so far...just brakes..what brand did you order from rockauto...and were you able to order the sensors as well?
@freddygarrett
3 жыл бұрын
Bendix brand rotors an pads ,, .an Yes brake pad sensor
@Alexfixty
3 жыл бұрын
It depends, sometimes from local warehouse, sometimes eBay or Amazon. Usually I look everywhere even call dealers :)
Can you post a link to the caliper rewind tool you used?
@Alexfixty
Жыл бұрын
amzn.to/3UQfuX5
@contrac4u
Жыл бұрын
on some RR you can also use a diagnostic tool or code tool to electronically retract the piston...
How do you get it out of service mode for a 2017 RR sport?
Can't get that caliber to retract back.... even in maintenance mode.....??? I wonder what I'm missing here
@startingtech3900
10 ай бұрын
Same what was your fix?
What about the brake sensors?
@Alexfixty
Ай бұрын
Replace them
But how do you replace the front ones???
@rhkavli
Жыл бұрын
Same procedure, sans the parking brake maintenance mode magick. So it's easier, apart from the calipers being a lot heavier.
I don’t think 2013 RR sport has service mode
Is it really necessary to put the car in maintenance mode to do rear brake pads? You also forgot to mention you need a special brake caliper piston retracting tool. And you need to get the right retracting pad to fit the brake piston otherwise you are wasting your time doing the job!!
@Alexfixty
2 жыл бұрын
0.40
@marcoperez6952
2 жыл бұрын
Missed that part on tool..sorry. But still puzzled why the parking brake must be put into maintenance mode. I have never used the PB. So it probably is not engaged and already retracted...correct?
@price9195
2 жыл бұрын
@@marcoperez6952 The parking brake comes on every time the car is turned off. It retracts but not all the way each time you drive. The new pads will be thicker than worn ones and they won't fit o/w.
They just quoted me 1600 for rear brakes at the dealer. I said I'll take the free car wash.
All watch’s rings removed while working on vehicles for your safety plus goggles