dare we ask who did the original install of those new gears? Would help some of us avoid a similar issue. At least tell us what state the original work was done in

Haha I was watching him point at the ring gear waiting for him to point to the chew marks on the carrier.

Inexcusable! I've been in the auto repair industry for a few decades now. This was laziness, negligence, flat out "zero F's given" (or some combination of all three). I'm sorry this happened to you. People like this are what gives my industry a bad name. Hopefully karma catches up with them. Bud glad to see you're back on the road, and better off that before. I can only imagine how much quieter and smoother it runs.

And this is often why I hate leaving it to the professionals... because when it goes wrong, you have no idea what they did or did not do... When you F' it up yourself, you normally know where you F'd it up!

I work for toyota for over 30 years ine thing a lot of tech don't do is to check preload on input shaft after assembly by using a brass punch and tapping in both side of the shaft and them measure preload I have never have a failure using this method

You can see why this install failed at 7:32. The pinion seal must be driven back well past flush with the end of the housing as it was done here. The pinion gear was drifting forward and back and that's the reason the carrier was all chewed up.

Thanks for the video. Ouchie on the poor carrier 18:05, good thing you brought it to a very knowledgeable tech.

This is very helpful. Thank you for sharing!

Thanks for sharing. Any gear howling/whine sounds after the install?

Would love to see a parts replaced list. This one mistake caused xx parts to be replaced and cost ??

Do u reuse the shim for the pinon gear to bearing from the old one or eliminate it?

Did the customer have an solid spacer to replace the crush sleeve or does the front diff not use a crush sleeve?

You don’t mind me asking, how did you install the new bearing race on the pinion heat it up?

Toyota front clamshell differential is harder to setup and very different front the rear, I believe few technicians know how to setup it properly, that's why you see so many has problem switch gears in the front because they were setup incorrectly! And the technican will blame it on Nitro gears instead of their incapability

@ken85225

8 ай бұрын

That's why I charge the big bucks for front clams👍👍👍....... special knowledge and special tools that had to be fabbed up.

My front pinion has the same issue I'm hoping I can get away with just doing some new pinions bearings and keep the same gears atleast until I have more money

Get a wheel cylinder horn wear the old bearings insides and used for shims setting preload preload

at 13:01... that is the inner race bearing.... lost that bearing!!! Hard to keep them intact!!!

Did he need to replace the carrier? Was it still structurally sound?

@BadassBrunette

3 жыл бұрын

Carrier was still useable.

The music isn't bad, but it's too loud

@BadassBrunette

3 жыл бұрын

Thanks for the feedback.

Right off the bat that's bs... only my pinion bearing is bad...

Could do without the music but good video.

@BadassBrunette

3 жыл бұрын

Thanks for the feedback.

Great video, but the music sucks.

@BadassBrunette

3 жыл бұрын

Noted. 🤙🏻

what a nightmare, you truthfully cannot trust anyone but yourself now a days. I've had to elarn how to do everything myself, if I can't do it then it won't be done.

9:50 Damn! That looks a lot worse than the noise I was imagining! Yikes!

It's this guy knows what hes doing.....no..

Popping Pimple KZread < Pulling Ear Wax KZread < Repairing Differential Housings KZread

what a waste, death by editing. unwatchable with audio so out of sync.

100/1000 finer than hair? You have thick hair! 125/1000 = 1/8...

Onley a clueless novice would put together a R&P without the proper preload on the bearings.

I wish the guy didn't explain what he was doing every 39 seconds, video could have been half the length with all the same good info.

@BadassBrunette

3 жыл бұрын

Thanks for the feedback. We wanted to create an educational video explaining in detail what was going on and what things to look for in case someone had a similar issue.

@PhoRunner

3 жыл бұрын

@@BadassBrunette ignore this clown named rick. Where’s the rest of the video!! Thanks for posting