Stuck Case? Try using the RCBS® Stuck Case Remover Kit. Comes with: body, drill, tap, cap and wrench.
Жүктеу.....
Пікірлер: 20
@deepskywishingwell2602 Жыл бұрын
30 years reloading and never had a stuck case. My first one this week. I did not know , never used a stuck case remover. Thank you guys, even old dogs need taught 😅
@LETCA8 жыл бұрын
It's a great tool! I was able to "rescue" my Hornady 444 Marlin Die that I'd stuck a case in several years ago. Well done, gentlemen!!
@bwhip11 жыл бұрын
Don't forget to back the decapping rod out as far as possible before drilling. It won't come out all the way, because the expander button won't pull through the neck while the case is still in the die.
@YouT00ber10 жыл бұрын
Guess what I just ordered off of amazon? Yep. Thanks for the video.
@jcm15110 жыл бұрын
Yeah what how you are skipping the problem of getting the decapping pin out of the way? And on a rcbs xdie this is even harder..
@MiamiNice5711 жыл бұрын
What is the best method to remove a LIVE Military Primer prior to stuck case removal? Steps so far: Froze the die x2 for 10 hrs let defrost at room temp 77 dgrs. Mobile 1 oil down the neck of the stuck case. The decapper tip broke and is in the case. Research= no way to truly deactivate primer. Military primmer is crimped and sealed with plastic. One forum recommend to grind a metal hanger to fit the flash hole and tap out. :{ any suggestions on how to do this safely?
@1murder99Ай бұрын
What do you do when the bolt twists off?
@lajostresser4828 жыл бұрын
This method and the removal kit would be wonderful; except in my case the decapping pin is sticking out through the primer pocket about a 1/4" and it is not moving, at least it does not appear to. I did not try to remove the sizing ball/decapping pin assembly yet anyway. Therefore the drilling/tapping method would not work? I would be grateful for any advice from anybody out there. Is my case a "just buy a new die"?
@YouT00ber
7 жыл бұрын
The pin can be loosened from the other side of the die. it doesn't come all the way out but you definitely can loosen it from the top and have it out of the way for drilling. when it's upside down i'll be out of the way of the drill bit. be careful w/ the tap as I snapped mine off inside the casing and I'm basically f*cked right now
@moe4him673 Жыл бұрын
Will this work on Lee Dies
@charltonlwalker2 жыл бұрын
Hornady remover tool works exactly the same way.
@Alfs_Armory9 ай бұрын
This is all well and good if you are sizing without the decapping pin in (can’t think why this might be though). Decapping pin is in the way. Do I have to drill and destroy the decapping pin? This is a bad design.
@thelittledetailscr7231
6 ай бұрын
Just wear safety glasses and drill it! No need to be so safe.
@YouT00ber7 жыл бұрын
ok, and so what do you do when you snap the tap off inside the shell casing?
@enigma6482
Жыл бұрын
Probably hammer it out using just the decapper. It may ruin the decapper, but those are about 1/4 the cost of the die.
@Airsoftforall8 ай бұрын
What does one do if that strips out? Seen a few on fb groups and answers from contact the seller to trash it.
@fnfailure
8 ай бұрын
Send the die in to RCBS they'll get it out and send it back
Пікірлер: 20
30 years reloading and never had a stuck case. My first one this week. I did not know , never used a stuck case remover. Thank you guys, even old dogs need taught 😅
It's a great tool! I was able to "rescue" my Hornady 444 Marlin Die that I'd stuck a case in several years ago. Well done, gentlemen!!
Don't forget to back the decapping rod out as far as possible before drilling. It won't come out all the way, because the expander button won't pull through the neck while the case is still in the die.
Guess what I just ordered off of amazon? Yep. Thanks for the video.
Yeah what how you are skipping the problem of getting the decapping pin out of the way? And on a rcbs xdie this is even harder..
What is the best method to remove a LIVE Military Primer prior to stuck case removal? Steps so far: Froze the die x2 for 10 hrs let defrost at room temp 77 dgrs. Mobile 1 oil down the neck of the stuck case. The decapper tip broke and is in the case. Research= no way to truly deactivate primer. Military primmer is crimped and sealed with plastic. One forum recommend to grind a metal hanger to fit the flash hole and tap out. :{ any suggestions on how to do this safely?
What do you do when the bolt twists off?
This method and the removal kit would be wonderful; except in my case the decapping pin is sticking out through the primer pocket about a 1/4" and it is not moving, at least it does not appear to. I did not try to remove the sizing ball/decapping pin assembly yet anyway. Therefore the drilling/tapping method would not work? I would be grateful for any advice from anybody out there. Is my case a "just buy a new die"?
@YouT00ber
7 жыл бұрын
The pin can be loosened from the other side of the die. it doesn't come all the way out but you definitely can loosen it from the top and have it out of the way for drilling. when it's upside down i'll be out of the way of the drill bit. be careful w/ the tap as I snapped mine off inside the casing and I'm basically f*cked right now
Will this work on Lee Dies
Hornady remover tool works exactly the same way.
This is all well and good if you are sizing without the decapping pin in (can’t think why this might be though). Decapping pin is in the way. Do I have to drill and destroy the decapping pin? This is a bad design.
@thelittledetailscr7231
6 ай бұрын
Just wear safety glasses and drill it! No need to be so safe.
ok, and so what do you do when you snap the tap off inside the shell casing?
@enigma6482
Жыл бұрын
Probably hammer it out using just the decapper. It may ruin the decapper, but those are about 1/4 the cost of the die.
What does one do if that strips out? Seen a few on fb groups and answers from contact the seller to trash it.
@fnfailure
8 ай бұрын
Send the die in to RCBS they'll get it out and send it back
RCBS, What all causes the case to stick?
@snake57
2 жыл бұрын
No lube
Kk((