The files to 3D-Print the snowmobile: www.myminifactory.com/object/...
Жүктеу.....
Пікірлер: 17
@Idontdohandles3 ай бұрын
Awesomeness for sure!!!! 😊
@UppfinnarAXEL
3 ай бұрын
Yea thanks! 😀
@3Drcnc2 жыл бұрын
Looks great! Semms to work really well in deep snow.
@curtisl.75992 жыл бұрын
I've been thinking about this Dynamic weight distribution I was thinking if you're familiar with mx vs atv dual joystick control would be realistic because to carve in deep pow you have to lean the direction you want to go an turn the skis opposite I'm thinking a drone controller would be ideal with two joysticks I've wanted a 3D printer for a long time so I can print one of these out thanks for the channel
How was i still unaware that you had a movable rider already? seem to work really well
@UppfinnarAXEL
Жыл бұрын
Yes, thanks. It does help with turning, but it can’t really lean the sled like a real rider can. I am experimenting right now with putting different weights on the rider. I have also tried using a stick radio for independent control of the rider and snowmobile. The left stick for throttle and steering, and the right stick for leaning of the rider. I found it really hard to control the snowmobile this way and I did not get any good results, but I will continue testing this later.
@Catboy-hr2qp Жыл бұрын
Where are the files for movable rider located? I'm assuming the servo plugs in to the same channel as steering?
@UppfinnarAXEL
Жыл бұрын
Yes, i use an y cable for channel 1. The files for the rider should be included in the mods folder on myminifactory
Пікірлер: 17
Awesomeness for sure!!!! 😊
@UppfinnarAXEL
3 ай бұрын
Yea thanks! 😀
Looks great! Semms to work really well in deep snow.
I've been thinking about this Dynamic weight distribution I was thinking if you're familiar with mx vs atv dual joystick control would be realistic because to carve in deep pow you have to lean the direction you want to go an turn the skis opposite I'm thinking a drone controller would be ideal with two joysticks I've wanted a 3D printer for a long time so I can print one of these out thanks for the channel
@UppfinnarAXEL
6 ай бұрын
kzread.info/dash/bejne/nXepmJmmZ8S0lZs.htmlsi=9HYbSy61Gm7c9av2
How was i still unaware that you had a movable rider already? seem to work really well
@UppfinnarAXEL
Жыл бұрын
Yes, thanks. It does help with turning, but it can’t really lean the sled like a real rider can. I am experimenting right now with putting different weights on the rider. I have also tried using a stick radio for independent control of the rider and snowmobile. The left stick for throttle and steering, and the right stick for leaning of the rider. I found it really hard to control the snowmobile this way and I did not get any good results, but I will continue testing this later.
Where are the files for movable rider located? I'm assuming the servo plugs in to the same channel as steering?
@UppfinnarAXEL
Жыл бұрын
Yes, i use an y cable for channel 1. The files for the rider should be included in the mods folder on myminifactory
@Catboy-hr2qp
Жыл бұрын
@@UppfinnarAXEL skeeride mods folder?
@UppfinnarAXEL
Жыл бұрын
@@Catboy-hr2qp yeah
How you make that rider
How Can i Get?
@UppfinnarAXEL
Жыл бұрын
www.myminifactory.com/object/3d-print-skeeride-rc-snowmobile-143369
Can you buy me one?
@Olilar397
Жыл бұрын
Build not buy😂