Hi, worked perfectly on my iNav loaded, OmnibusF3 v1.1 with HC5883 magno in my GPS puck. Thanks again for great video.

Thanks, Painless. I connected my OLED, on to a SP F3 Deluxe, to the I2C1 on the bottom of the board (nice and simple) Then connected to cleanflight. Did as you said and it burst into life. Thanks for that.

Thanks for a famous moment :-) thanks to your video I manage myself up to read the inav manual's part about Oled displays and found out that programming the flight controller isn't yet supported.

@Painless360

7 жыл бұрын

+Villy Feltmann not yet, why not request this in the project via github?

@vovsen123

7 жыл бұрын

I'll do that. Just not used to ask without contributing in some way.

Thanks just set one up on my Ranger 2000.

I have a whole box full of these. I'm definitely putting one in my plane.

Acutally this is extremely cool for cockpits with fpv cams

@bomberaustychunksbruv4119

3 жыл бұрын

I tried and the FPV cam refresh will affect the screen vision to the point where its unreadable.

@4QFiles

3 жыл бұрын

@@bomberaustychunksbruv4119 Uggg

Piece of cake, stuck one In my dart with an F411 and GPS, shame you can't specify the display results but can have everything. The screens are about 3quid on aliexpress

Hi..trying to add an oled display to a anyfc f7 flight controller..using INAV of course. I can't get this to work ..and in INAV1.7.2.there seems to be no CLI feature display capability. Any comment on what I'm doing wrong.. I have a baro on the same I2c bus which works...? regards JH

thanks for the help could not understand why mine was not working,looked at your board,looked at the one I ordered,looked the same.Then I flipped it over and I saw they sent me The wrong board.Wiki would have been useless for that as they only show the front

Can you run one on betaflight?

thank's another one!!

Interesting, thanks Lee : ) Do you know if it is possible for the OLED to display PID values? That way, we can increase or decrease the gain values using TX and see the changes on the OLED. Thanks ~

@Painless360

2 жыл бұрын

I'm not sure as I stopped using an OLED when the INAV LUA script came out.. Best of luck!

Hi can I run this if I'm running Telemetry and a GPs ? omnibus v3 f4 pro fc using uart 3 which is on the J10 connector on the fc to feed the Telemetry thanks in advance

@Painless360

6 жыл бұрын

+CrazyHorse FPV UK you will need a spare UARTut on your flight controller. Have a look for one that isn't being used and that will be your best bet. Best of luck!

hi i have spent a while trying to do this on my onibus f4 pro,i have oled feature ticked, the same oled as on this video and its wired up correctly , but i get no signs of life from the oled , i have tested 2 oled screens . any ideas why i can not get it to work ?

@Painless360

6 жыл бұрын

As I mention in the video, some makes of the OLED (CIRUS, back in the day) were pains to get working. The one I used in the video fired up fine..

Congratulations for your videos, they are a great help. In Inav4.1 When you activate OLED screen, the information in the OSD of the VTX glasses stops working. Any ideas?

@Painless360

2 жыл бұрын

None, sorry. I don't use OLEDs any more as I use the INAV LUA script on the radio to check status..

does the F35 lighting from furious fpv have the SLA and SDA Pins??? becasue i searched for the pins in the manual but i coudnt find any pins, are these pins on every FC or only on spesific ones?

@Painless360

5 жыл бұрын

I don't think it does. See my F35 build for what I did..

@kevinschindler8052

5 жыл бұрын

@@Painless360 hi thanks for the quick reply :) i just looked through the F35 FC series but i dont think i heard you talking about the F35 having any support for OLED displays :(

Can someone tell me what the little spinning "R" in the top right corner of the display mean? Also what does HDUP mean? Thank you for the help.

@Painless360

2 жыл бұрын

I'm guessing you are not a regular viewer. Check out the latest INAV series. HDOP stands for horizontal degrees of precision. It tells you how good the GPS 3D lock is.. Happy flying

Another excellent tutorial! I've used these little displays with the Pixhawk [where the connections allow for simultaneous use of the OLED and a mag] but now I'm setting up a Matek F722-STD with iNAV and was wondering: Is there is any way to connect both a SSD1306 OLED display and a HMC5883L compass module? Cheers!

@Painless360

6 жыл бұрын

I've not tried as I don't connect the compass in fixed wing.. If it works - let me know! :D

@cvonp

6 жыл бұрын

Thanks for the reply. I've had decent luck on my S800 with an Omnibus F3 and the mag located in a wingtip, but I think I'll try running GPS-only on the F7 build

@cvonp

6 жыл бұрын

Just did a breadboard with an Omnibus F4 + OLED + mag and [once I changed the address of the OLED] they appeared to work great together =)

@Painless360

6 жыл бұрын

Cool! How did you change the address?

@cvonp

6 жыл бұрын

I have a couple of these displays from different manufacturers and two of the boards had pads on the reverse side to select between two addresses. The selected address is bridged with an SMD resistor that you can desolder and move as needed =)

Arent these the same screens used in the diversity goggle receivers? As in; they break if you look at them? How durable would these be inside a model?

@xavierayayaell546

7 жыл бұрын

Salih Ergezen first ask what is the point of doing this.

@Painless360

7 жыл бұрын

They are not built to be bullet proof but we've printed ABS covers for the ones we use here and all are still working (he says, touching wood for good luck!) ;)

Hi Painless I flashed iNav over my old version of clean flight. A SP F3 borad.My 450 sized quad now barley flies. Any tips on something im missing. it kind just oscillates very badly and flips. I have tried various pid settings but not having much luck. for now i have just gone back to cleanflight which is working fine. Thanks!

@Painless360

7 жыл бұрын

What trouble shooting have you tried already? Tricky to offer constructive advice apart from the usual - filters, reduce vibration etc.. without any detail of what you see/have seen change with your testing..

@josefschalk4353

7 жыл бұрын

thanks, i have just done the typical as you have suggested. i do remember though that the first pid controller "lux" wasnt great for my quad and i had to switch it over to mw23 but looks like in inav and now cleanflight v2 they have taken that option way. perhaps it can be done via cli. just wanted to see if there were any gotcha's i was missing. thanks for your time.

@OneTwo-wt8qv

7 жыл бұрын

I have had 2 banggood F3 Racing Deluxe boards act weird after loading and configuring INAV. I went back to Cleanflight on both , one of the F3's is bricked and overheats, the other is unreliable. Not sure if clone boards have issues, maybe, CHEERS !

@josefschalk4353

7 жыл бұрын

Cheers. I ended up going to betaflight. Had to raise the p all the way to 200 and it was kinda flyable. I got my new 5 inch racer so my 10 inch quad isn't getting that much attention now 😮

Hello, this Oled screen work on the new SpeedyBee f405 Wing? And if it do how can it be connected? Thanks

@Painless360

Жыл бұрын

I wouldn't recommend adding an OLED screen now as I've seen issues with things like servo jitter with them. If you want to see things like arming status and GPS status I'd recommend using the INAV lua script on the radio... Best of luck

Hello ! Sorry for my english.. Can i connect in parallel SCL and SDA from my Oled Screen and SCL and SDA from magnetometr ? In my FC only one pair pins, but i wanna use Oled and Mag in same time. Thanks!

@Painless360

6 жыл бұрын

Not sure, All I know about INsv is in the playlist. Best of luck!

@erksampat9328

6 жыл бұрын

Probably should work. As long as the i2c addresses of both devices are not the same.

@jacobstech1777

4 жыл бұрын

Space Stranger did you find out?

Has anyone here done this on a f405-wmn as I can't get it working

Would this work with apm.2.6

@Painless360

7 жыл бұрын

I Googled 'APM and OLED' and the answer isn't clear. APM is getting very long in the tooth now.. Happy flying!

Great video. For some reason mine only kind of works. I wired up and turned on OLED and rebooted. Screen shows Matek and other data and then the first four lines are good with status; voltage; current draw and alt but nothing for GPS. The bottom of the screen looks like static. I will swap out screen tonight to see if it is a screen issue but was curious if there are any other settings I must choose. I purchased MakerFocus I2C OLED 0.96 Inch OLED Display Module IIC SSD1306 128 64 LCD White from Amazon.

@Painless360

3 жыл бұрын

I've had issues with the bigger oled screens with timing issues.. Best of luck with it

@ChandlerWoodruff

3 жыл бұрын

@@Painless360 I am honored for your response. Your videos have helped me so much over the years. It led me to buying the AR Pro as well as a couple of AR Minis to build confidence (Minis have Vistas and Pro has DJI Air Unit) What size screen did you use (size and lines/resolution). If smaller I will purchase the smaller screen as a test.

@ChandlerWoodruff

3 жыл бұрын

@@Painless360 I returned and purchased three others from Amazon and they all work. I am guessing that the fields are hard coded and can not be changed like we like we can change OSD or via CLI but I will keep researching.

Did you ever 3D print a housing for the display?

@Painless360

6 жыл бұрын

I did, it was very specific to the screen I had though..

@cvonp

6 жыл бұрын

I like the idea of having it nestled in the motor mount as your video suggests 👍

hey Lee i think this would be an amazing feature to intagrate into my fleet i am just now seeing this since i dont have that many years started in 2019 and i just recently switched over to wings and drones i think with firmware on the internet today and possibly with the community this could really do a ton of stuff for us just so we dont have to have our goggles on while setting up or to look at the screen when a warning is active please let me know you take on this thanks sir

@Painless360

2 жыл бұрын

I don't use them any more as the INAV LUA script does all of the same things and can be used to monitor things in flight too... Happy flying

Hi lee! I had a problem! my oled shows not all pixels in the first two screens But when i arme the wing all pixels on the oled was shown!

@Painless360

4 жыл бұрын

Not sure, there was an issue with the larger OLED screens last time I looked...

@airhogfpv1283

4 жыл бұрын

@@Painless360 thx for the fast answer I had a 0,96 blue oled from Amazon! I'll try another one I orderd 5 of them 😁for 20. €

So this can or can not be used in conjunction with a GPS unit?

@Painless360

7 жыл бұрын

+BLeeKiis Too can

@bleeksbentbits3150

7 жыл бұрын

Awesome, thank you too for the prompt reply once again! :)

@Painless360

7 жыл бұрын

No problem! Happy flying!

Hi, Is it possible with mission planner with omnibus f3 pro

@Painless360

4 жыл бұрын

Mission planner is the companion software for the ardupilot family of flight control software. Please check out my recent omnibus flight controller build WITH arduplane for more details on the art of the possible. Best of luck!

@hobbypilots794

4 жыл бұрын

@@Painless360 thank you

If I use magnetometer, then I can’t use oled?

@Painless360

4 жыл бұрын

You can have several things on the i2c bus....

@Shenanigans3D

3 жыл бұрын

@@Painless360 I was wondering the same. I use a external dedicated mag on the sck/sda and not finding to much literature on running both.

aurdopilot has a similar option. I searched your chan but didnt see anything about it. Might make a quick fun video to show that too. As with many things like this I find out its an option when I find your video and don't know about it before that.

@Painless360

2 жыл бұрын

Thanks for the idea! Using something like the Yappu LUA script is a more common option now... Happy flying

@Clickmaster5k

2 жыл бұрын

@@Painless360 Do you mean sending that info to the tx and using yappu script there or is there a way to use yappu on your model with a tiny screen?

@Painless360

2 жыл бұрын

On the radio.. No need for glasses to read it and it still works when the model is 200ft above you :D

Hi :D

Hi painless360 l bought a Flip 32 f3 omnibus. I've added a link of the one I bought. It's slightly different to the most omnibus f3 boards my one got a white port next to the osd and it has 10 pins the first two is Vout and Vin plus eight more pins. Do I need to use any of these pins. If so what connector is this. Thank you in advance. www.readytoflyquads.com/flip-32---f3---omnibus-bec---w-baro-option

@Painless360

7 жыл бұрын

Not sure what you mean, that link looks very similar to ours..

@gavinhoon9140

7 жыл бұрын

+Painless360 Sorry I'm a multiwii user, got left behind with the caveman. If you look at the J9 connector the one you're using in the video, it has 6 pins, mine has 10 pins. One of the photos in the link shows the J9 connector with 10 pins. Do you need to use any of the pins on this connector? When using INav. Hope this makes more sense.

I found this which indicates that the OLED display wont work on a AnyFC F7 github.com/iNavFlight/inav/issues/1994

@Painless360

6 жыл бұрын

Thanks for posting, I've not tried any F7 based ones yet..