My RC shopping cart is done! Thanks for everything you showed in your videos.

@snowkingcro

4 жыл бұрын

Thanks for the comment!

@cursedshoppingcart2366

4 жыл бұрын

@@snowkingcro The only problem is that the motherboard shots off at 38v

@snowkingcro

4 жыл бұрын

If you need 5V for the RC Receiver, you can use 5V from Hall sensor!

@cursedshoppingcart2366

4 жыл бұрын

@@snowkingcro I'm already using 5v from hall sensor. But that doesn't solve the cott off problem .

@snowkingcro

4 жыл бұрын

well... i had that problem... i woukd try to charge up the batterry to 100% (~42v), and flash again... maybe the borad reads that the batery is dead at 38v...

LOL love it. I an see me sitting in a garden chair with a long cool drink doing the mowing.

I am so gonna build this for my grandpa

Hi, thanks for the video I just subscribed. There are a lot of folders in the link you provided. Do you simply upload the single hexfile located in the build folder to STM32Cube Programmer? Sorry, I'm new to this.

Awesome job! Can you show me how you connected the receiver to the motherboard? I have the firmware from your other video and I'm not sure if the wiring is different to enable steering.

@snowkingcro

4 жыл бұрын

Thanks. The wiring has only one difference, and that's the ADC1 for steering and ADC2 for throttle. To better clarify, ont this video kzread.info/dash/bejne/ZI6bj9WpaaWqj8o.html it can be seen on 3:00 min. mark!

@dudedotmichael

4 жыл бұрын

​@@snowkingcro 3:19 is the only close up I see and even that is not clear. It looks like you are taking 5v from the right hall cable to power the receiver (White wire). But then you have three wires. I'm guessing you are using ADC1 and ADC2 and GND raw.githubusercontent.com/NiklasFauth/hoverboard-firmware-hack/master/pinout.png But I have no idea how you connect those to the receiver. Is ADC1 just going to the signal port on channel 1 and ADC2 going to the signal port on channel 2 and power and ground going to any other channels power and ground?

@snowkingcro

4 жыл бұрын

I used 5V from hall sensor and adc1 adc2 and ground from from the left sensor board.

@dudedotmichael

4 жыл бұрын

snowkingcro but how does that connect to the receiver on the radio?

@snowkingcro

4 жыл бұрын

i'll post a picture in my repository and send you the link.

Nice

@snowkingcro

4 жыл бұрын

thanks 😊

Where i can find the correct firmware to make the same project. At the end you say there is some problem in the firmware. Thanks and congratulations for this fantastic project!!!! Bye from Italy ps: can i use a flysky remote radio?

@snowkingcro

3 жыл бұрын

The hex code to flash your board can be downloaded here: github.com/snowkingcro/hoverboard-firmware-hack-esk8/tree/RC-Steering/build Or you can find the link in the description of my video. You can use any 2-3 channel radio remote. Cheers from Croatia ;)

@MattiaRaggiDrum

3 жыл бұрын

@@snowkingcro Thanks for the reply! I would like to build a radio-controlled lawnmower as in the video, which firmware should I use? On the site I find two versions of the firmware. One file has the word master at the end of the name and another file the word sterring. thanks again for your kindness. ps: is there a connection diagram? from the video dive you explain the connections is not clear. Thanks from Italy.

@snowkingcro

3 жыл бұрын

Hi. use the steering FW, and as for wiring on this link: kzread.info/dash/bejne/ZI6bj9WpaaWqj8o.html on the 3:00 mark is the wiring diagram

@AChi__

3 жыл бұрын

@@snowkingcro I built mine about three weeks ago, and I wish I'd seen your great video before I built mine. I would've made some changes especially with regard to the wheels. Your setup allows for zero degree turns, mine sorts does it too, but because mine is four wheeled, with the rear wheels being the powered wheels, it requires more power to achieve the zero turns. You did and excellent job with yours. Kudos!

Just wondering if you still did any improvement in lawnmower performance?

@snowkingcro

2 жыл бұрын

Well, I bought some sensors to implement with an arduino board, but i'm stuck due the lack of free time :/

Did you add pull down resistors to green and blue wires?

@snowkingcro

2 жыл бұрын

Do you mean the cables on the Hall sensor? No, not at all, just keeping the wires short

bjr mr je trouve sela supert jaimerait faire un chario radiocomender pouvez vous me dir quelle firmware avez vous mi sur la carte et le branchement du recepteur . merci d'avence et bonne fin d'annee

@snowkingcro

Жыл бұрын

On this video, look in the comments, there is the link to the Firmware

Moze li neko objasnjenje ili link za nacin povezivanja RC kontrolera na hoverboard

@snowkingcro

Жыл бұрын

Na ovom videu kzread.info/dash/bejne/ZI6bj9WpaaWqj8o.html na 2:54 je slika, koju treba pauzirati. Transmiter je spojen na LEFT SENSOR BOARD

Are the wheels 6.5 inch or 8.5? Do the wheels slip? I'm wondering wether I neet to buy a "all terrain" one or not.

@marianofpv

Жыл бұрын

Even some used ones come with a little seat with the third wheel.

E buraz pomagaj hocu nesto slicno da napravim, znas li mozda kako da pomocu rc resivera controlisem motor od howerborda nema nigde na youtubu

@snowkingcro

2 жыл бұрын

hm, želiš upravljati hoverboardom kao ja na mom videu? Pa, morat ćeš flashati firmware od hoverboarda sa firmverom u linku ispod videa... ali upamti da je to nepovratan proces, pa ako to napraviš, nećeš ga više moći vratiti na funkciju hoverboarda

Does the motors overheat in the summer ?

@snowkingcro

Жыл бұрын

They tend to be warm but I had no problems whatsoever. It works aprox. one hour per moving, so... it gets warm, but thats it... I can hold to the wheel with my hands

Hey thanks for showing us the great project, I’ve followed your tutorial and everything works great except the motors seem to run constantly when the ppm throttle value gets over a certain range, works okay on steering. I even bought the same tx and receiver as you but didn’t change the issue. Have you had any issues like this? Ps check my hover board project , Thanks

@snowkingcro

3 жыл бұрын

well, i think it could be the problem with long cables, always try to keep them short. i really didn't have any problems, but i got some reports of my friends that certain motherboard react different to the code upload.

@fbm7986

2 жыл бұрын

@@snowkingcro often thicker wires helps reduce voltage drop over distance. Not sure how it correlates to data, but considering cat 6 is just thicker cat5 I imagine it’s something similar with data

Episch!

Hi, have you ever flashed a motherboard with gd32f1003 chip with your custom firmware?

@snowkingcro

4 жыл бұрын

well until now i flashed three boards, didn't checked which chip it was...

Rm

Pozdrav, svidja mi se tvoj projekt, ja sam zamislio nesto slicno ali za djeci auto, imam hoverboard, narucio sam ESC-e za motore ali bih trebao pomoc oko upravljanja, vidim da se kuzis u to pa mi mozda mozes pomoci sa arduinom, naime moram sloziti elektroniku da mi glumi diferencijal kada skrecem u lijevo da mi od uzima gas na lijevom kotacu, ili dodaje na desnom a u desno kontra. Ako mi mozes pomoci mozemo se cut preko maila prsa.kristijan.biker@gmail.com hvala!

@balkandiytutorials7659

2 жыл бұрын

Jel si uspeo to napraviti ja pravim nesto slicno