Hi uncle mark, Can’t wait to come see you guys.

@mosquitonkosak

3 жыл бұрын

Me neither

This is a awesome build. Two strokes are always a good time. I took a Razor MX and put a predator 212cc motor on it. Man does it fly, it is a little scary running it wide open lol.

@mosquitonkosak

3 жыл бұрын

holy crap thats awesome! these were for kids so they dont need that much power.

@321fabrication4

3 жыл бұрын

@@mosquitonkosak Even us big kids need something to ride! :) Do you have any other project you are working on?

@mosquitonkosak

3 жыл бұрын

@@321fabrication4 I'm working on converting my son's 12v quad power wheel into a chain driven 24v motor like the ones used on scooters. Check out my other videos for other builds.

Thank you for this vid. A family down the street from me threw out both an MX350 and a Mod Bella. What a waste, I grabbed both out the trash and am going to do something fun with them. Seeing your build has given me lot of ideas.

@mosquitonkosak

3 жыл бұрын

Thank you. Check out my other video of the mod Bella. My daughter loves riding that thing still. More to come!

@maxpower1911

3 жыл бұрын

@@mosquitonkosak Thanks, I checked that one out. You've got some pretty good designs. I was actually thinking of doing a gas conversion on this Bella, since it's got a little more room in the frame to accommodate a pocket bike motor. And try to keep as much of the original plastics intact (though de-pinked). I want to fabricate a little fake cargo box for the rear deck, and hide the fuel cell in there. And I might keep the MX350 electric. So basically I'll end up with the opposite of what you've got.

@mosquitonkosak

3 жыл бұрын

@@maxpower1911 oh very nice! Getting the motor to mount on the bella is probably the hardest due to the sproket spinning one direction. They do make a converter to make it go the other way if you'd want to use that. Amazon has all the parts. I have an empty frame of the bella and going to turn that into gas powered too. I also have a goped that I'm going to figure out how to put that same 49cc motor on it. Just another project 😆 on the mx350, use the same 48v motor I did cause it'll work perfectly

@maxpower1911

3 жыл бұрын

​@@mosquitonkosak The build quality on these Razor bike frames is pretty good for being kid stuff. Both the ones I picked up were well worn, had been stored outdoors, and still only minor surface rust. No bends or dents. I got a 50cc scooter from China, I wish the welds on that frame looked as good.

@mosquitonkosak

3 жыл бұрын

Ya the Chinese stuff had welds from amateur welders. I have ridden that Bella scooter and the frame holds up perfect and I'm not a small guy. Grind that surface rust off with an angle grinder and you should be good.

Good idea. An it's good to know I'll use a ten speed bike Road Rear Derailleurs to take up the chain slack.

@mosquitonkosak

3 жыл бұрын

Most new chains stretch after being used very little.

That's badass!

This is awesome!!! I have one that’s already stripped to the frame I just need to install the engine! I was wondering did u cut the center support bar?

@mosquitonkosak

3 жыл бұрын

Yes I did otherwise the engine won't fit. I have since removed the engine from the wood block and welded on a plate to the frame. Much more sturdy.

@izzyespinoza4965

3 жыл бұрын

@@mosquitonkosak thats pretty cool man, im doing the same for my little bro

Bro you are a genius

@mosquitonkosak

4 ай бұрын

Just a dad who wants to see things go fast

@myturn3886

2 ай бұрын

I have 3 of these which would love to get a gas motor in it. Where are you located?​@@mosquitonkosak

i saw this vid and i had a razor mx350 of my own and gas swapped it and it went 34 miles an hour.

@user-ll1sj5sf3f

Ай бұрын

What engine did you put in it

What engine did u put it on where did u find it bc I'm looking to do one of these builds

@mosquitonkosak

3 жыл бұрын

www.amazon.com/dp/B074GYV11B/ref=cm_sw_r_cp_apa_fabc_oha8FbZMNKY49?_encoding=UTF8&psc=1

Wondering if u shorten the chain it will help keep chain tight n solve the loose chain problem.

@mosquitonkosak

3 жыл бұрын

I have since put in a gear reducer and changed the sprocket and chain to a t8f chain cause they don't make connectors for the chain I have. I cant make it shorter so I gotta bigger one and shortened that one and put it on. Follow up video to come...

How they put the wod

Hey! I recently did one of these exact builds, and to be quite honest, you actually helped me a lot! And I just had one question, will it hurt the engine to run it with no pipe? I’ve been trying to find an answer to this for a while, but came up short. Thank you!

@mosquitonkosak

2 жыл бұрын

Thats why I do this. Yes it will run with no pipe. Not required but it'll be really loud.

@vlogs5008

Жыл бұрын

What did you do abought the sprocket spinning the wrong way?

@nich5611

Жыл бұрын

@@vlogs5008 I took some real thick copper wire and put it around the sprocket and attached to wheel. You could also just weld the ball bearings together aswell

@WilliamArcher-vj5uz

9 ай бұрын

​@@nich5611can you help with mine where do I connect it

Hey man, do you know if these support a swingarm extansion? I have a variation of this model and it doesnt have a rear shock like the older models do. I know the swingarm extension mod is fully compatible with the ones that have a rear shock but im asking for mine since yes... i know theyre meant for kids around the usual age of 8-12 or maybe 13 but they support up to 140 pounds in weight or atleast my model does from what i know. I myself weight 135 sometimes my weight goes up to 137. Its rarely gone up to 140 but not any higher. Im 21 by the way. And like i said i know theyre meant for youth but as i mentioned it supports my weight and ive also seen some people on youtube mod these models and some seem to be the same age as me. Others seem to be older. Either way if you need to know, the reason i want to do the extension mod is because i want to do a gas conversion aswell yet i want to install a somewhat big motor also the model of my mx350 has a steel tube where you placed your motor in. It might be removeable but im not so sure about removing it.. and well the extension is so i can have a good enough soace for bith the gas motor and maybe put a small backup battery. I know it seems wierd but my dad has done these things with old bikes turning them to motorized dirt trikes having both gas motor and a small battery so i can hook up both a led as a head light and a small tail light in the rear. I dont know how well to explain it but i hope you understand what i mean. Either way ive been typing to much at this point jaja but yeah. If it is that you know if its modable then please let me know i just wanna be sure. If its not possible then i can still just add a small motor but like i said illd rather prefer a motor aswell as a small battery with it. Thanks in advance

Is there a way to flip the freewheel on the wheel so the sprocket can spin the other way? I’m trying to put a 50 cc engine in it and I have the same problem

@mosquitonkosak

Жыл бұрын

No because it only turns one way while the other way it'll spin without the sprocket. You can buy a converter for the engine that will spin the sprocket the opposite direction from Amazon.

Hello, I have a razor mx400 and I want to convert into gas but I don’t know how. Can you please do a step by step tutorial pleaseeeee!

@mosquitonkosak

3 жыл бұрын

I'm in the process of making the video right now

@zaidr6761

3 жыл бұрын

Thank you so much

Do you need a battery connected to it to get spark or can you just pull start it without a battery

@mosquitonkosak

3 ай бұрын

No battery required

Did you move the sprocket from right side to Left ? I have an electric mini bike and want to convert it to gas but on mine sprocket was on the other side

@mosquitonkosak

3 жыл бұрын

Yes I took the tire off and flipped it around and reinstalled it. I would recommend welding the sproket to the bearing so its one piece. Just a couple of tacs should do it.

@mattatone20

3 жыл бұрын

@@mosquitonkosak take the sprocket off and 180 flip it put it back on. Then the sproket will lock and freewheel like it did on other side. It bolts onto the wheel

How much did this cost at the end of the day? I just looked at a Suzuki 50cc dirt bike for my 5 yr old. It was $1K. After all this work, and these parts, seems you could just have the real thing, and far better. Safer too.

@mosquitonkosak

3 жыл бұрын

The bike I got for free and parts included, it wasn't more than $150. I enjoy building these for my kids.

what size sprocket are you running? Do they make a quieter muffler?

@mosquitonkosak

Жыл бұрын

The link was in the description about the sproket. That is the quietest they make. 2 strokes are loud man lol

What type of bolts did you use to mount it?

@mosquitonkosak

2 жыл бұрын

4 bolts that screw into the motor and the wood was mounted with screws. wood has since been removed and it is now a metal plate.

How did you Mount for 2 x 4 to the frame

@mosquitonkosak

2 жыл бұрын

with screws underneath the frame. I have since welded a plate

What chain did you use?

@mosquitonkosak

3 жыл бұрын

The one in this video is a T25 chain but the one on it currently is a T8F which is stronger and bigger. Check out part 2 for the updated version.

Where u buy clutch sprocket

@mosquitonkosak

3 жыл бұрын

It comes on the motor. Check out my other videos for the new gear reducer used.

Where did you find a chain that long? i have been looking all over and coming up empty...

@mosquitonkosak

3 жыл бұрын

The one I have is from a kit that is no longer available. I have since converted it to a bigger chain for reliability and speed and it is much better quality. I had to swap sprokets and now have a gear reducer attached to the engine. www.amazon.com/dp/B08D75RQGP?ref=ppx_pop_mob_ap_share

@matthewwyatt8927

3 жыл бұрын

@@mosquitonkosak ok thanks!

@matthewwyatt4758

3 жыл бұрын

@@mosquitonkosak hi, I got the chain part down but now I am having problems mounting the engine do u have any tips for mounting

@mosquitonkosak

3 жыл бұрын

@@matthewwyatt4758 2 ways: mount the engine to a piece of pressure treated wood then mount the wood to the motor. Attach a metal plate to the motor then weld that plate to the frame. I did the second one. I will be making another video about how exactly I did it.

@matthewwyatt4758

3 жыл бұрын

@@mosquitonkosak ok thanks!

can you put a faster motor on it?

@mosquitonkosak

3 жыл бұрын

technically you can upgrade the current one but being that this one goes about 20mph, Im not going to do that. You can if you want but just be in mind that there is limited room.

So you put the wire on the sprocket to make it stay

@mosquitonkosak

4 ай бұрын

welded it made it stay permanently

How did you do the wiring please post a video or something please lol

@mosquitonkosak

Жыл бұрын

What exactly do you want to know? The kill Switch?

@meandmyrccar1336

Жыл бұрын

@@mosquitonkosak sorry I’m a little late, yes the kill switch, I’ve been trying to find wiring diagrams but was not successful.. help would be much appreciated!

@mosquitonkosak

Жыл бұрын

@Me And My Rc Car run a wire and attach it to the block of the engine. Then run that same wire to a kill switch you can buy. Then from that kill switch run that wire to the spark plug wirrle that sticks out from the spark plug itself

@meandmyrccar1336

Жыл бұрын

@@mosquitonkosak Thanks A LOT, I was always wondering what the wires were coming out from where the spark plug wire splits, great to know that’s the kill switch wires that came with the engine and the kill switch..

What kind of oil do you use

@mosquitonkosak

4 ай бұрын

It's a 2-stroke engine. The gas and oil go together inside the tank. I buy 2-stroke mixture pre-made 50-1 ratio

@TylerKnight-xo2dl

4 ай бұрын

@@mosquitonkosak can you use 2 cycle super tech

@mosquitonkosak

4 ай бұрын

As long as it's the right mixture with gas and oil yes

Stupid question why didn't you not put the motor where the electric motor was

@mosquitonkosak

3 жыл бұрын

The motor was too big. The electric motor was significantly smaller than the 49cc one.

@MyIronman8

3 жыл бұрын

@@mosquitonkosak that's weird I've got that same motor and it shoved in where the electric motor is

@mosquitonkosak

3 жыл бұрын

@@MyIronman8 i couldn't get it to fit and also the fairings would get in the way

@mosquitonkosak

3 жыл бұрын

Plus the exhaust

I’m doing build right know

@mosquitonkosak

Жыл бұрын

Lemme know if you need any help.

do a vid about it 1 more time and JUST how u did it

@mosquitonkosak

3 жыл бұрын

I will be making a video of the updates that I have done to it and a step by step on how I did it.

@jahviervazquezvazquez7905

3 жыл бұрын

@@mosquitonkosak ok sounds good becaue i have the mx 350 im tryying to make it gas

@jahviervazquezvazquez7905

3 жыл бұрын

all i need to do is buy the engine and spray paint

@jahviervazquezvazquez7905

3 жыл бұрын

and how much was all that

@mosquitonkosak

3 жыл бұрын

@@jahviervazquezvazquez7905 less than 100

She got more balls then me to ride with no brakes

@mosquitonkosak

3 жыл бұрын

It has disc brakes now

@MambazReturn

2 жыл бұрын

@@mosquitonkosak What disc brake did you use?

@mosquitonkosak

2 жыл бұрын

@@MambazReturn just a set from a mountain bike. Nothing special

I started at four let him ride

@mosquitonkosak

3 жыл бұрын

My deal with him was if he can ride a bike without training wheels, then he can ride it

@stevenwolfe2803

3 жыл бұрын

@@mosquitonkosak fuel line running along side exhaust,,be very careful when putting the seat back on ,it’s not touching pipe🙃have same bike &a motor from mini quad ,I will be doing ,just took back rim off to wire it Up. I think it’s better then tac weld,,cause them free wheels always break. The spokes can take more force ,I will share if it comes out good 😜