Range Rover P38 # 088 - Fuel Injection Pump - Part 1 - Removal
Автокөліктер мен көлік құралдары
This is the sequel to my FIP Top Gasket replacement. Please see video # 083 • Range Rover P38 # 083 ... if you want to know how to remove all the bits required to remove the fuel injection pump (FIP), which we'll do in this video. You'll need to remove the intake manifold to gain access to the pump.
You'll need a few speciality tools:
LRT-12-108 - Timing locking pin (flywheel)
LRT-12-117 - 17mm high pressure line removal tool
LRT-12-119 - Pump removal tool (pusher and sprocket holder)
17mm Allen key
Most of these tools came in the Laser Tools 4077 (Sealey VSE5538) kit which contains:
LRT-12-108 - Timing lock pin (flywheel)
LRT-12-112 - Camshaft position plate
LRT-12-114 - 2x tensioner pins
LRT-12-115 - Timing chain tensioner release
LRT-12-118 - Pump adjuster
LRT-12-119 - Pump remover
And a few parts are recommended:
STC2015 - Fulcum o-ring (cover over pump axle on tensioner)
STC2279 - Pump o-ring to timing cover
The next video in this sequel will be about replacing the seals to recondition the pump.
You can reach me at gamuso@gmail.com if you want to get in touch with me.
Follow me on Twitter: / 0ddj4rl3 or Instagram: / 0ddj4rl3
Please consider subscribing. And as always please comment below and I'll respond as best as I can.
Thanks for watching, and I hope you found this video interesting.
Пікірлер: 16
Great video. Great step by step instructions. I'm glad my latest fuel pump leak didn't need the pump to be removed. Time will tell though!! Well done.
@WorkOnP38
5 жыл бұрын
Thanks Alan. Hope yours holds up :) Mine was leaking from the head seal, and both actuator seals. Thanks for watching and taking time to submit comments!
great video again, my dear freind, you are a star, for the thing you do,its made my life so much easyer, keep post my mate, godbless nick uk swindon
Very good video.
@WorkOnP38
4 жыл бұрын
Thanks for the feedback and for watching, Rui!
brilliant videos every time so much detail is enclosed .i have a problem were my p38is in limp mode but no lights on dash no fault codes present any ideas as to were i should be looking please
Utrolig bra video :) har du mulighet til og dele manualen for jobben med meg ? :)
Hey! where did you find the manual to do all the work on an m51?
without the special tool, should you still be able to wiggle the pump off when everything is disconnected from it???
Salut j'ai problème où nevou de pompe injection lond rover p38 j'arrive pas à régler la ralentir
Can you help with my rangerover p38 So its not cracking over it has been underwater for 17hrs btw we have drained the engine and rebuilt the becm and all esc its ignition works and the starter turns but not unless you connect a boost pack to it and spark it out it just clicks and it sounds like the relay isnt working it has working ones in it but its just not cranking overany suggestions
@WorkOnP38
4 жыл бұрын
Hi. Would be hard to say what the exact problem is when there is water damage. Make sure the fuse box is cleaned properly inside and out, and check the starter relay (and all other relays). I'd probably replace all relays and fuses to avoid any corrotion issues. Good luck, I hope you manage to get it working. PS! The wiring diagrams contain a lot of useful troubleshooting tips so you might want to check it out: drive.google.com/open?id=1DE1zkP5G42BWkh8QdGEIK4wlkSkLpqNC Thanks for wathcing!
just 1 thing did you rebuild the pump, if not are you going too, cheers nick swindon uk
@WorkOnP38
5 жыл бұрын
Thanks Nick. In my next video I'm rebuilding the pump so stay tuned. Thanks for watching, and for the kind words. Just glad the videos are of use. Take care!