Range Rover lost key programming with Autel im608pro
Жүктеу.....
Пікірлер: 20
@kenyamena14016 ай бұрын
Did anyone find the solution to the vehicle not starting?
@tommyherrera64562 ай бұрын
Does it matter how many what’s the 10k resistor is?
@abiliobaulane52459 ай бұрын
How find right key frequency?
@PavLockLocksmith Жыл бұрын
Did you removed costing before soldering?
@Lasselectricalgarage8 ай бұрын
Can you locate the T1 resistor
@kellsautos9183
8 ай бұрын
I wish I had one at hand
@PavLockLocksmith Жыл бұрын
Did you removed the t1 chip?
@kellsautos9183
Жыл бұрын
Yes
@convertathletics45649 ай бұрын
Just did one. Eeprom read, start key and writing was "successful" when i get back to car silent alarm still flashing blinkers and red light on cluster still blinks. No crank still. Any ideas?
@alexfurman4137
8 ай бұрын
I have the same problem, how did you do it?
@Eurosmithpro
8 ай бұрын
Havent been back to vehicle to finish yet. A couple JLR techs have told me you must purchase a new CEM if car was locked when keys were lost. Which i dont believe, but not any success videos that ive actually found yet. I imagine one might need JLR SDD software in order to control the ignition and active alarm status. Also, removing all fault codes is an issue when AKL.
@Eurosmithpro
8 ай бұрын
Every shows the soldering and key program "success" but ive yet to see full video of programming AND going back to vehicle and using the working key. Lol
@Lasselectricalgarage
8 ай бұрын
Why do you put the resistor between the wires?
@user-mx9xx5zw3x
4 ай бұрын
Привет, подскажи пожалуйста как решали вопрос?@@Eurosmithpro
@VFVT1019 ай бұрын
Where are you located?? I need this done.
@kellsautos9183
9 ай бұрын
Nigeria. Umuahia Abia state
@AverilDoyle Жыл бұрын
..What is "the second phase of the whole operation"? I figured that you had a part two video, but no. Did you have to do anything special after the "make start key" function and writing the .BIN file back to the module? I went and read the keys and they now match the key ID's for the missing keys, but the vehicle still will not start. Is there a synchronization step that i am missing?
Пікірлер: 20
Did anyone find the solution to the vehicle not starting?
Does it matter how many what’s the 10k resistor is?
How find right key frequency?
Did you removed costing before soldering?
Can you locate the T1 resistor
@kellsautos9183
8 ай бұрын
I wish I had one at hand
Did you removed the t1 chip?
@kellsautos9183
Жыл бұрын
Yes
Just did one. Eeprom read, start key and writing was "successful" when i get back to car silent alarm still flashing blinkers and red light on cluster still blinks. No crank still. Any ideas?
@alexfurman4137
8 ай бұрын
I have the same problem, how did you do it?
@Eurosmithpro
8 ай бұрын
Havent been back to vehicle to finish yet. A couple JLR techs have told me you must purchase a new CEM if car was locked when keys were lost. Which i dont believe, but not any success videos that ive actually found yet. I imagine one might need JLR SDD software in order to control the ignition and active alarm status. Also, removing all fault codes is an issue when AKL.
@Eurosmithpro
8 ай бұрын
Every shows the soldering and key program "success" but ive yet to see full video of programming AND going back to vehicle and using the working key. Lol
@Lasselectricalgarage
8 ай бұрын
Why do you put the resistor between the wires?
@user-mx9xx5zw3x
4 ай бұрын
Привет, подскажи пожалуйста как решали вопрос?@@Eurosmithpro
Where are you located?? I need this done.
@kellsautos9183
9 ай бұрын
Nigeria. Umuahia Abia state
..What is "the second phase of the whole operation"? I figured that you had a part two video, but no. Did you have to do anything special after the "make start key" function and writing the .BIN file back to the module? I went and read the keys and they now match the key ID's for the missing keys, but the vehicle still will not start. Is there a synchronization step that i am missing?
@alexfurman4137
8 ай бұрын
I have the same problem, how did you do it?
@user-mx9xx5zw3x
4 ай бұрын
😮Привет, помогите пожалуйста, как решили вопрос?