DIY kayak keel gaurd for under 20 dollars from start to install
Жүктеу.....
Пікірлер: 101
@curiousgeorge4674 Жыл бұрын
I have spent a lot of time this year in-between fishing trips working on my kayak. I did this early on with mine. I formed mine pretty much the same way and cut it with my table saw using two guide rails so it turned out perfect. I formed it twice because I wanted to see if I could improve the form fit and I was able to get what I think was a beautiful fit. I also reheated the edges practicing first on scrap and got a very smooth transition from pvc to kayak. I did sand the transition further to make it really nice and perfect. I sanded the inside of the pvc to rough it up. I thought it would work well with the already roughed up keel. I used a light coating of jb-weld to hold it all in place over night. I propped the kayak on saw horses and used several cut blocks of metal as weights with bungee cords strapped around to insure pressure against it over night. I was willing to use some bondo if needed to insure the form transition but I didn't see where it would have done any improvement. The next day I removed the weights and all looked well. Mater of fact it looked so good I wished I had videoed the process. The transition appeared seamless. I plan on painting my kayak this winter so I decided to paint the bottom as a way to test my learned painting skills after studying all summer on how to pain a kayak. My attempt worked really well and it made the keel work done look really fantastic. Looks factory! I don't expect people to put the work in that I did but I use this kayak everyday and it has a long year in the water. I fish tournaments every week almost and I admit I am very rough of the bottom of my kayak. So for me to do this when needed it will save me a lot of money. I suspect if I ever need to do this again it will be way down the road. So the time I put in will be very well worth it and keeps some of my fishing winnings in my pocket. I am actually considering extending the work I did on the keel all the way down because this kayak has a decent ridge going all the way down the bottom and it looks just as worn as my keel. Thanks for the idea.
@97kt694 жыл бұрын
Good tutorial but could skip the tunes. 🤔
@massacmongo9954 жыл бұрын
Great video but the music is too loud and distracting
@jimthompson7173 жыл бұрын
Use a table saw to split the pvc lengthwise. Sand the inside of the pipe for better adhesion.
@russellmoore15334 жыл бұрын
The change from speech noise level to 'music' noise level is very annoying!
@MDWackerman
3 жыл бұрын
It adds to the reality of DIY
@turbotwerp4 жыл бұрын
You sir, are a freaking genius. I have the exact same kayak, even the same color, and the boat ramps were killing my bow. Thank you for the brilliant DIY. I used gorilla heavy duty 30lb mounting tape, I have no doubt the thing is stuck on. The only mod I made was that I ran a bead of silicone around the entire thing to seal it and make it a little more hydrodynamic.
@rpgoutdoors5022
4 жыл бұрын
Glad it worked for you!
@debluewaters8031
2 жыл бұрын
Does PP stick on PE?
@mattdaniel60584 жыл бұрын
I would recommend scratching up the pvc with a piece of sand paper. The tape would have better adhesion.
@johnnybarbar74352 жыл бұрын
Don't remove all of the tape backing before you install the guard. Just start with a couple inches peeled back so that the backing can be removed as you press the guard into place. The side pieces are adhering and making it more difficult to fully seat when all the backing is removed initially. Depending on your keel profile, one might be able to peel the entire center tape backing and only peel the side tape backing as you proceed with the install.
@CerealKiller9794 жыл бұрын
Awesome video man! Fellow Titan supporter here. Thanks!
@B1gHagar4 жыл бұрын
Hey Buddy, I'm very interested in this process but I've learned not to get too excited youtube "fix its" without a year plus review. So, how about it. Can you show us the repair? Is it still on? Any good gouges? Thanks in advance.
@rpgoutdoors5022
2 жыл бұрын
Unfortunately I don't own one of the kayaks anymore but the other had to be reglued around 6 months. But the piece is still holding tough just needed to be re secured.
@thiodorchalkias890611 ай бұрын
Nice video thanks for sharing!!! I use resentlly the fins of bicycle wheels as a front kayak protector!!! It was already courved and with a little heat modification it was perfect!!!
@FRECUENSIAX Жыл бұрын
Excellent idea, thank you very much from Puerto Rico 🇵🇷🎣😎🤙
@hectoralers844 жыл бұрын
Nice idea and well done. The only doubt i may have is the adhesion method. But i appreciate you posting! Thanks!
@michaellovell25184 жыл бұрын
If I do this, I might try to feather the edges a bit to reduce drag. I like the trend of replaceable keel guards on newer models, but I purchased an older used kayak without this feature. The hull is pretty scratched up already, but solid enough, so I might experiment with trying to smooth it out a bit first.
@rpgoutdoors5022
4 жыл бұрын
We did a speed test and found the difference was not noticeable. The edges are feathered but could definitely use small amount of caulking, due to the thickness of the 2 way tape it will have small gap.
@michaellovell2518
4 жыл бұрын
Probably wouldn't be noticeable over short distances, but drag would obviously be increased to some extent. It's not a bad idea, and any decrease in performance might be insignificant when weighed against the benefits. Still, any improvements would be worthwhile if you paddle all day. "The difference was not noticeable" is a misnomer, by the way. It would have to be noticeable in order to determine that there was any difference. You might have said "we noticed no difference," or "the difference was insignificant." The former would raise questions regarding test parameters, and the latter would be a relative determination.
@rodbrown83067 ай бұрын
Great innovation, I need to do similar, thanks so much for the tips. God Bless.
@thiodorchalkias8906 Жыл бұрын
Maybe to use an aluminium tube doing the same (almost) steps is better of course there's necessary a pipe bender instead of heater...
@bennylandron4 жыл бұрын
Very good idea.Nice work too! Thanks for the info.
@sme49693 жыл бұрын
i would of used the guard to draw around on the kayak and taped the kayak 1st and also roughened the inside of the guard
@yourwrong61252 ай бұрын
Use kydex. Also use a special marine bonding adhesive dont use double sided tape....
@justinwht36702 жыл бұрын
White irrigation PVC will eventually degrade in sunlight. Grey electrical conduit PVC is outdoor-sunlight resistant.
@barnaclebill16156 ай бұрын
I wonder how the adhering process went and long-term
@teamcrooks691329 күн бұрын
How about using a silicone bonding agent instead of tape?
@thewoods54062 жыл бұрын
Yes sir I like it! Fine hack definitely doing this to my new ascend 133 tournament fishing kayak
@bretshivers83523 жыл бұрын
love the idea! how well will the double sided tape hold in a submerged enviroment? i wonder if some 3m 5200 would work as well
@paulbunyun-xi9by5 ай бұрын
Marine Goop works well also
@ALFarrell-kv6ok Жыл бұрын
I'm wondering if that is a special outdoor and waterproof 2-sided tape. And what the brand name is.
@olhesty21963 жыл бұрын
Excellent vid man. Gonna use some irrigation pipe (thin stuff for the rear keel and maybe kydex for the sides. But definitely sch 40 for the front!
@yauck1
3 жыл бұрын
Wear a respiratory mask when you heat up the pvc: “Although PVC is flame resistant, PVC products release toxic hydrogen chloride gas when heated. These corrosive gases can spread faster than flames, trapping building occupants before they have a chance to escape. Hydrogen chloride gas is lethal when inhaled.”
@chrism80134 жыл бұрын
That is awesome!! Did you use "automotive" double sided tape? That stuff has great adhesive on it... All kayak companies should make a solid pvc bow guard like that for their popular models. Id gladly pay upwards of $50 for a perfectly formed piece of rugged pvc to protect the bow from scraping. Either that, or beef up the plastic on the inside along the abusive sections of the keel to at least an inch thick. My bow section gets a lot of abuse from lifting from the rear to load the cart and from the cement boat ramp on the canal that I launch/land on. However, mine has a sacrificial keel keel block on the rear, why cant they make one for the bow...
@rpgoutdoors5022
4 жыл бұрын
Yes I did use 3m double sided tape, but be sure and use the 10 or 15lb because the 20 lb is thicker. That allows water to come in and deteriorate the adhesion faster.
@MrRaivisk Жыл бұрын
Sand inside of the pipe and better use glue for hdpe. Solution with tape will not work for low temperatures.
@olhesty21963 жыл бұрын
Love it man! I got sch 80 grey. Got a grey yak so all is good. Wanted the black ABS plastic pipe, but local supply didn't have it, or if they did, it was 20' and $18. I am too cheap for that.
@adamsifford6228Күн бұрын
Would jb weld be better than tape?
@benjiereeves49195 жыл бұрын
Great idea. Gonna try this on mine!
@fisherman420 Жыл бұрын
Awesome video sir!
@tonymayer43724 жыл бұрын
Great ideal! Did it stay on alright? Did you end up sealing around the edges with anything or was it just fine the way it was? Thank you.
@rpgoutdoors5022
4 жыл бұрын
Never sealed it and it continues to hold tight. I recommend using thinner 3m tape if you can find. Thanks and good luck!
@pitchkapizda83552 жыл бұрын
Genius idea love it
@danmidkiff54164 жыл бұрын
I have to agree about the music. How long did this setup last without coming off? Did the tape hold? Thanx
@andrewbland6252 жыл бұрын
Looks great! I might try this. I used a pliable stick-on keel guard and it went on pretty sloppy around curves. I'm also afraid the irregular edges will slow me down. Is tape really the best way to adhere the guard to the keel? What about Marine Goop? I suppose JB Weld might be too difficult to remove if necessary?
@graceleah32163 жыл бұрын
Wouldn’t clear waterproof silicone worked best ? It would seal it up, and leave no space.
@Demop_VW_garage
3 жыл бұрын
I used sikaflex 221 works well so far.
@romavo
3 жыл бұрын
I sealed a keel hole from the inside with a tube of DAP 100% silicone. Several months ago still dry. Stumbled across this video looking to plastic melt and reshape my keel properly. Will put these guards on after that. Thanks for the video
@josephthayer79602 жыл бұрын
I like your video and I like the last few comments from the other commentators, You mentioned that you reglued it again. Have you or anyone on here thought about Silicone adhesive or rubberized the PVC pipe prior to installation?
@zam2008644 жыл бұрын
very well explained ,thanks
@rpgoutdoors5022
4 жыл бұрын
Thanks we hopefully have more coming 👍
@carlyleswan36463 жыл бұрын
The tape will not hold in water very long. You should have used 5200 marine caulking. This also would have filled in the space that you see under the pvc. Sand the kayak and pvc lightly. Caulk it with 5200.
@jdaniels1313
3 жыл бұрын
He answered that 5200 might be a little too permanent if keel guard wears/breaks and needs to be replaced. 3M 4200 seems like a good choice for that criteria.
@r0bd3 жыл бұрын
Out of curiosity, why use PVC and not just weld a thick strip of HDPE?
@leemp337
3 жыл бұрын
pvc semi formed already and very thick? thoughts? did you use HDPE? Where did you source it from?
@r0bd
3 жыл бұрын
@@leemp337 I used HDPE. I sourced it from a 55gal drum so it was even thicker, but you can also use 5gal buckets like the ones from lowes/home depot.
@cowboysam19573 жыл бұрын
The loud music drove me nuts
@oklahomaoutlawfishin9026 Жыл бұрын
I thought about doing this to mine.
@oday35142 жыл бұрын
Great idea! But that muzak... :O
@teresawysocki57292 жыл бұрын
Great job!
@zipzip82394 жыл бұрын
Awesome idea. How long does the tape usually hold for?
@bart2u Жыл бұрын
Even electrical pipe is too thick to contour on curves of hull.
@estebantresamigos4 жыл бұрын
Chulada!! Gracias will do same on my canoe.
@caryverhalen4 жыл бұрын
I would waterproof silicone around the edges especially the front
@keithmenia8470
2 жыл бұрын
I like everything about this. You can also order colored furniture grade PVC off Amaz0n.
@FishingwiththeOz3 жыл бұрын
I am going to try this. Did you use 1/2 inch or 1 inch tape?
@CrunkyOMan834 жыл бұрын
Can u post all the links where u can buy all the stuff be good to have a list, cause I never knew about that type of pvc cutter!
@rpgoutdoors5022
4 жыл бұрын
We bought all of if from home depot, the pvc used is just electrical pipe.The heat gun allows you to cut it easily when heat is applied. I will try to screen shot the cart with all the supplies if possible
@Vzavala6224 жыл бұрын
It has been 9 months, is the tape still holding? Thanks for setting up this video.
@rpgoutdoors5022
4 жыл бұрын
It finally started to let loose so I removed it reapplied new tape. But the guard seems to be holding up pretty good.
@eliebrams1537
4 жыл бұрын
@@rpgoutdoors5022 Do you think it would work with some liquid nails adhesion caulking?
@rpgoutdoors5022
4 жыл бұрын
@@eliebrams1537 It should but removing it after it wears out is the question.
@FlexDRG
3 жыл бұрын
@@rpgoutdoors5022 fair point. If it sticks too well it's hard to replace. If it doesn't stick good enough it comes off to easily. But perhaps a proper watertight mounted bolt or rivet might aid in staying on.
@markybolton4 жыл бұрын
Curious! Why didn't you use marine glue?
@rpgoutdoors5022
4 жыл бұрын
This makes it easier to replace when it wears out. I didn't know how well Marine glue would be to remove and replace.
@jdaniels1313
3 жыл бұрын
@@rpgoutdoors5022 Good answer, makes sense. The 5200 can be pretty permanent. I understand 3M's 4200 would be removable without damaging the boat. Your method seems to work well and is inexpensive and approachable. Thanks for the helpful video!
@Cousin_Gregg2 жыл бұрын
How has this held up?
@romavo3 жыл бұрын
Thx for the video. Good idea! Agree on the tunes. But you wouldn't like my tunes.
@saqwedcxz123 жыл бұрын
Nice
@mluc11113 жыл бұрын
Try shoe Goo , silicone glue is too soft
@garyg24 жыл бұрын
good video, horrible music...
@teresawysocki57292 жыл бұрын
You should own a kayak repair job to make money! 👍
@adamsifford6228Күн бұрын
Great job terrible pop rave music 🎶 tho.
@caiaqueirojs.66264 жыл бұрын
Like garantido
@greenmile94964 жыл бұрын
Don’t drag your kayak or canoe on the ground...it’s like using 10 grit sandpaper on it when you do...😬 Float your craft parallel next to the shoreline or riverbank when getting in and out and you’ll never have to waste your time & money on repairs.✌️😃
@kratzerb
4 жыл бұрын
Doesnt always work that way when you're fording creeks. I have to drag across long rock sections quite often.
@greenmile9496
4 жыл бұрын
@kratzerb...understood...I work part time renting canoes & kayaks at a lake & see A LOT of avoidable damage to the bow & sterns. Sounds like you’re going where “no one has gone before”! Almost forgot: “O.H.”....😃👍
@kratzerb
4 жыл бұрын
I-O... yep, skinny creeks. But I have a "beater" specifically for little water, and pvc keel guards. :)
@greenmile9496
4 жыл бұрын
@kratzerb....”Whatever floats yer boat”...(!) Anything that gets you out there is all that really matters 🛶
@TztokkJad4 жыл бұрын
What about using clear silicone to adhere it?
@rpgoutdoors5022
4 жыл бұрын
Haven't tried that I may give it a go.
@adamsifford6228Күн бұрын
Terrible pick for music.
@bassjunkie48814 жыл бұрын
Wish I would've seen this 3 months ago, I wore a 6 inch long 1 1/2 inch wide hole in the hull of my field and stream shadow caster 123, I didn't think the plastic was that thin or soft , kayak is only 3 months old n field n stream, and dicks sporting goods won't fo anything about it
@rpgoutdoors5022
4 жыл бұрын
If you look inside your kayak sometimes they leave pieces purposely for patching holes. I heat up a large wrench like one and a quarter size, and use the smooth end to mend up any holes or deep scratches.
@michaellovell2518
4 жыл бұрын
Don't lift the bow when you drag it. Try to drag it flat rather than on the stern keel only. I put an extension on my front toggle handle for dragging.
Пікірлер: 101
I have spent a lot of time this year in-between fishing trips working on my kayak. I did this early on with mine. I formed mine pretty much the same way and cut it with my table saw using two guide rails so it turned out perfect. I formed it twice because I wanted to see if I could improve the form fit and I was able to get what I think was a beautiful fit. I also reheated the edges practicing first on scrap and got a very smooth transition from pvc to kayak. I did sand the transition further to make it really nice and perfect. I sanded the inside of the pvc to rough it up. I thought it would work well with the already roughed up keel. I used a light coating of jb-weld to hold it all in place over night. I propped the kayak on saw horses and used several cut blocks of metal as weights with bungee cords strapped around to insure pressure against it over night. I was willing to use some bondo if needed to insure the form transition but I didn't see where it would have done any improvement. The next day I removed the weights and all looked well. Mater of fact it looked so good I wished I had videoed the process. The transition appeared seamless. I plan on painting my kayak this winter so I decided to paint the bottom as a way to test my learned painting skills after studying all summer on how to pain a kayak. My attempt worked really well and it made the keel work done look really fantastic. Looks factory! I don't expect people to put the work in that I did but I use this kayak everyday and it has a long year in the water. I fish tournaments every week almost and I admit I am very rough of the bottom of my kayak. So for me to do this when needed it will save me a lot of money. I suspect if I ever need to do this again it will be way down the road. So the time I put in will be very well worth it and keeps some of my fishing winnings in my pocket. I am actually considering extending the work I did on the keel all the way down because this kayak has a decent ridge going all the way down the bottom and it looks just as worn as my keel. Thanks for the idea.
Good tutorial but could skip the tunes. 🤔
Great video but the music is too loud and distracting
Use a table saw to split the pvc lengthwise. Sand the inside of the pipe for better adhesion.
The change from speech noise level to 'music' noise level is very annoying!
@MDWackerman
3 жыл бұрын
It adds to the reality of DIY
You sir, are a freaking genius. I have the exact same kayak, even the same color, and the boat ramps were killing my bow. Thank you for the brilliant DIY. I used gorilla heavy duty 30lb mounting tape, I have no doubt the thing is stuck on. The only mod I made was that I ran a bead of silicone around the entire thing to seal it and make it a little more hydrodynamic.
@rpgoutdoors5022
4 жыл бұрын
Glad it worked for you!
@debluewaters8031
2 жыл бұрын
Does PP stick on PE?
I would recommend scratching up the pvc with a piece of sand paper. The tape would have better adhesion.
Don't remove all of the tape backing before you install the guard. Just start with a couple inches peeled back so that the backing can be removed as you press the guard into place. The side pieces are adhering and making it more difficult to fully seat when all the backing is removed initially. Depending on your keel profile, one might be able to peel the entire center tape backing and only peel the side tape backing as you proceed with the install.
Awesome video man! Fellow Titan supporter here. Thanks!
Hey Buddy, I'm very interested in this process but I've learned not to get too excited youtube "fix its" without a year plus review. So, how about it. Can you show us the repair? Is it still on? Any good gouges? Thanks in advance.
@rpgoutdoors5022
2 жыл бұрын
Unfortunately I don't own one of the kayaks anymore but the other had to be reglued around 6 months. But the piece is still holding tough just needed to be re secured.
Nice video thanks for sharing!!! I use resentlly the fins of bicycle wheels as a front kayak protector!!! It was already courved and with a little heat modification it was perfect!!!
Excellent idea, thank you very much from Puerto Rico 🇵🇷🎣😎🤙
Nice idea and well done. The only doubt i may have is the adhesion method. But i appreciate you posting! Thanks!
If I do this, I might try to feather the edges a bit to reduce drag. I like the trend of replaceable keel guards on newer models, but I purchased an older used kayak without this feature. The hull is pretty scratched up already, but solid enough, so I might experiment with trying to smooth it out a bit first.
@rpgoutdoors5022
4 жыл бұрын
We did a speed test and found the difference was not noticeable. The edges are feathered but could definitely use small amount of caulking, due to the thickness of the 2 way tape it will have small gap.
@michaellovell2518
4 жыл бұрын
Probably wouldn't be noticeable over short distances, but drag would obviously be increased to some extent. It's not a bad idea, and any decrease in performance might be insignificant when weighed against the benefits. Still, any improvements would be worthwhile if you paddle all day. "The difference was not noticeable" is a misnomer, by the way. It would have to be noticeable in order to determine that there was any difference. You might have said "we noticed no difference," or "the difference was insignificant." The former would raise questions regarding test parameters, and the latter would be a relative determination.
Great innovation, I need to do similar, thanks so much for the tips. God Bless.
Maybe to use an aluminium tube doing the same (almost) steps is better of course there's necessary a pipe bender instead of heater...
Very good idea.Nice work too! Thanks for the info.
i would of used the guard to draw around on the kayak and taped the kayak 1st and also roughened the inside of the guard
Use kydex. Also use a special marine bonding adhesive dont use double sided tape....
White irrigation PVC will eventually degrade in sunlight. Grey electrical conduit PVC is outdoor-sunlight resistant.
I wonder how the adhering process went and long-term
How about using a silicone bonding agent instead of tape?
Yes sir I like it! Fine hack definitely doing this to my new ascend 133 tournament fishing kayak
love the idea! how well will the double sided tape hold in a submerged enviroment? i wonder if some 3m 5200 would work as well
Marine Goop works well also
I'm wondering if that is a special outdoor and waterproof 2-sided tape. And what the brand name is.
Excellent vid man. Gonna use some irrigation pipe (thin stuff for the rear keel and maybe kydex for the sides. But definitely sch 40 for the front!
@yauck1
3 жыл бұрын
Wear a respiratory mask when you heat up the pvc: “Although PVC is flame resistant, PVC products release toxic hydrogen chloride gas when heated. These corrosive gases can spread faster than flames, trapping building occupants before they have a chance to escape. Hydrogen chloride gas is lethal when inhaled.”
That is awesome!! Did you use "automotive" double sided tape? That stuff has great adhesive on it... All kayak companies should make a solid pvc bow guard like that for their popular models. Id gladly pay upwards of $50 for a perfectly formed piece of rugged pvc to protect the bow from scraping. Either that, or beef up the plastic on the inside along the abusive sections of the keel to at least an inch thick. My bow section gets a lot of abuse from lifting from the rear to load the cart and from the cement boat ramp on the canal that I launch/land on. However, mine has a sacrificial keel keel block on the rear, why cant they make one for the bow...
@rpgoutdoors5022
4 жыл бұрын
Yes I did use 3m double sided tape, but be sure and use the 10 or 15lb because the 20 lb is thicker. That allows water to come in and deteriorate the adhesion faster.
Sand inside of the pipe and better use glue for hdpe. Solution with tape will not work for low temperatures.
Love it man! I got sch 80 grey. Got a grey yak so all is good. Wanted the black ABS plastic pipe, but local supply didn't have it, or if they did, it was 20' and $18. I am too cheap for that.
Would jb weld be better than tape?
Great idea. Gonna try this on mine!
Awesome video sir!
Great ideal! Did it stay on alright? Did you end up sealing around the edges with anything or was it just fine the way it was? Thank you.
@rpgoutdoors5022
4 жыл бұрын
Never sealed it and it continues to hold tight. I recommend using thinner 3m tape if you can find. Thanks and good luck!
Genius idea love it
I have to agree about the music. How long did this setup last without coming off? Did the tape hold? Thanx
Looks great! I might try this. I used a pliable stick-on keel guard and it went on pretty sloppy around curves. I'm also afraid the irregular edges will slow me down. Is tape really the best way to adhere the guard to the keel? What about Marine Goop? I suppose JB Weld might be too difficult to remove if necessary?
Wouldn’t clear waterproof silicone worked best ? It would seal it up, and leave no space.
@Demop_VW_garage
3 жыл бұрын
I used sikaflex 221 works well so far.
@romavo
3 жыл бұрын
I sealed a keel hole from the inside with a tube of DAP 100% silicone. Several months ago still dry. Stumbled across this video looking to plastic melt and reshape my keel properly. Will put these guards on after that. Thanks for the video
I like your video and I like the last few comments from the other commentators, You mentioned that you reglued it again. Have you or anyone on here thought about Silicone adhesive or rubberized the PVC pipe prior to installation?
very well explained ,thanks
@rpgoutdoors5022
4 жыл бұрын
Thanks we hopefully have more coming 👍
The tape will not hold in water very long. You should have used 5200 marine caulking. This also would have filled in the space that you see under the pvc. Sand the kayak and pvc lightly. Caulk it with 5200.
@jdaniels1313
3 жыл бұрын
He answered that 5200 might be a little too permanent if keel guard wears/breaks and needs to be replaced. 3M 4200 seems like a good choice for that criteria.
Out of curiosity, why use PVC and not just weld a thick strip of HDPE?
@leemp337
3 жыл бұрын
pvc semi formed already and very thick? thoughts? did you use HDPE? Where did you source it from?
@r0bd
3 жыл бұрын
@@leemp337 I used HDPE. I sourced it from a 55gal drum so it was even thicker, but you can also use 5gal buckets like the ones from lowes/home depot.
The loud music drove me nuts
I thought about doing this to mine.
Great idea! But that muzak... :O
Great job!
Awesome idea. How long does the tape usually hold for?
Even electrical pipe is too thick to contour on curves of hull.
Chulada!! Gracias will do same on my canoe.
I would waterproof silicone around the edges especially the front
@keithmenia8470
2 жыл бұрын
I like everything about this. You can also order colored furniture grade PVC off Amaz0n.
I am going to try this. Did you use 1/2 inch or 1 inch tape?
Can u post all the links where u can buy all the stuff be good to have a list, cause I never knew about that type of pvc cutter!
@rpgoutdoors5022
4 жыл бұрын
We bought all of if from home depot, the pvc used is just electrical pipe.The heat gun allows you to cut it easily when heat is applied. I will try to screen shot the cart with all the supplies if possible
It has been 9 months, is the tape still holding? Thanks for setting up this video.
@rpgoutdoors5022
4 жыл бұрын
It finally started to let loose so I removed it reapplied new tape. But the guard seems to be holding up pretty good.
@eliebrams1537
4 жыл бұрын
@@rpgoutdoors5022 Do you think it would work with some liquid nails adhesion caulking?
@rpgoutdoors5022
4 жыл бұрын
@@eliebrams1537 It should but removing it after it wears out is the question.
@FlexDRG
3 жыл бұрын
@@rpgoutdoors5022 fair point. If it sticks too well it's hard to replace. If it doesn't stick good enough it comes off to easily. But perhaps a proper watertight mounted bolt or rivet might aid in staying on.
Curious! Why didn't you use marine glue?
@rpgoutdoors5022
4 жыл бұрын
This makes it easier to replace when it wears out. I didn't know how well Marine glue would be to remove and replace.
@jdaniels1313
3 жыл бұрын
@@rpgoutdoors5022 Good answer, makes sense. The 5200 can be pretty permanent. I understand 3M's 4200 would be removable without damaging the boat. Your method seems to work well and is inexpensive and approachable. Thanks for the helpful video!
How has this held up?
Thx for the video. Good idea! Agree on the tunes. But you wouldn't like my tunes.
Nice
Try shoe Goo , silicone glue is too soft
good video, horrible music...
You should own a kayak repair job to make money! 👍
Great job terrible pop rave music 🎶 tho.
Like garantido
Don’t drag your kayak or canoe on the ground...it’s like using 10 grit sandpaper on it when you do...😬 Float your craft parallel next to the shoreline or riverbank when getting in and out and you’ll never have to waste your time & money on repairs.✌️😃
@kratzerb
4 жыл бұрын
Doesnt always work that way when you're fording creeks. I have to drag across long rock sections quite often.
@greenmile9496
4 жыл бұрын
@kratzerb...understood...I work part time renting canoes & kayaks at a lake & see A LOT of avoidable damage to the bow & sterns. Sounds like you’re going where “no one has gone before”! Almost forgot: “O.H.”....😃👍
@kratzerb
4 жыл бұрын
I-O... yep, skinny creeks. But I have a "beater" specifically for little water, and pvc keel guards. :)
@greenmile9496
4 жыл бұрын
@kratzerb....”Whatever floats yer boat”...(!) Anything that gets you out there is all that really matters 🛶
What about using clear silicone to adhere it?
@rpgoutdoors5022
4 жыл бұрын
Haven't tried that I may give it a go.
Terrible pick for music.
Wish I would've seen this 3 months ago, I wore a 6 inch long 1 1/2 inch wide hole in the hull of my field and stream shadow caster 123, I didn't think the plastic was that thin or soft , kayak is only 3 months old n field n stream, and dicks sporting goods won't fo anything about it
@rpgoutdoors5022
4 жыл бұрын
If you look inside your kayak sometimes they leave pieces purposely for patching holes. I heat up a large wrench like one and a quarter size, and use the smooth end to mend up any holes or deep scratches.
@michaellovell2518
4 жыл бұрын
Don't lift the bow when you drag it. Try to drag it flat rather than on the stern keel only. I put an extension on my front toggle handle for dragging.
loud suck music
Another kayak that was never used
Nice