We repair a damaged thermal cut-out on the Pure Pleasure QDK11-D electric blanket.
Жүктеу.....
Пікірлер: 50
@brankotod46463 жыл бұрын
That thermal fuse did not burn out for no reason. The heating cable must be damaged somewhere. This cable consists of two wires, external and internal, similar to a coaxial cable. When the cable overheats, a short circuit is made between these wires, the two resistors start to heat up and then the thermal fuse burns.
@collinshlatshwayo66424 жыл бұрын
thank you for this.was about to trash 4 new controllers and the blankets as i couldnt figure out what was wrong
@radiorob2 жыл бұрын
I had the exact same problem and also traced it to the thermo fuse in the controller. Mine is also the queen size blanket. I purchased an exact replacement from a mail order electronic supplier in Vereeniging for about R12 and soldered it in, applying more of the white heat sink compound. I took the precaution of moving the good controller to the opposite side of the bed and the repaired controller to my side. When I switched the repaired controller on it worked perfectly but when my wife switched her side on the thermo fuse blew shortly afterwards in that controller indicating a problem was on her side of the blanket. We have only used this blanket for 2 winter seasons.
@vimal32
Ай бұрын
Shes hotter than you 😂
@davidl78465 жыл бұрын
Top Man :) and keep up with the videos you helped me save my controller
@vivianbrink4744 жыл бұрын
Thank you so much, really helpful.
@robviolin15 жыл бұрын
thanks for the good info.
@muskymcg4 жыл бұрын
Nice video buddy. Why don't they put a reset button on cut out? People just throw away blanket and controller... Just a thought:)
@rashaadsujee151824 күн бұрын
Hi there I have the same blanket & having a issue where the light comes on but not getting warm. I messured the thermal fuse & it shows 0.2 should I replace.
@xx38682 жыл бұрын
Hi i tested the thermal fuse and it was good and also checked 240V on the output side of the fuse and it was there. All diodes test good- no other electronics on this one, but i have 4 wires from the blanket and no matter what combination i try i get at min is a few thousand ohms?? does that mean the coils in the blanket have had it as i noticed the little light sometimes come on and not although the blanket did heat , now i get nothing on any setting and no light or warmth on blanket. Thanks
@rendanin83294 жыл бұрын
Good job thanks
@ElisabethBernardi-dx4mt4 ай бұрын
How much électricity does it take if used a whole night ?
@ElisabethBernardi-dx4mt4 ай бұрын
How much électricité does it take for a whole night heating ?
@MokgatlaMolepo4 жыл бұрын
Mine switched on but it's not heating up. What could be the problem?
@nannonriechel31792 жыл бұрын
Howdy! I have the king size one and a queen and the switches are not moving up or down the controllers? Do you have an idea for me? One side of the King works but with major force to get the button to move into position 1,2 or 3. The other side doesn't want to move at all. The queen has both sides not moving on the controller. It's like it stuck!?
@arishapather89554 жыл бұрын
How do you replace the Fuze if it blew up?
@yamjak2 жыл бұрын
Hi, stupid question.... But need to know. Do you guys just replace your electric blankets when they need to be cleaned Or.......how do you clean 'em?
@sylviaholburn84593 жыл бұрын
Who repairs these switches in and around Randburg area ?
@kamogelophala27963 жыл бұрын
I am having the same issue , I have opened mine and found the same sticky like white thing around those thermostats, how much must i pay for it to be replaced ? Estimation please
@Optorockit Жыл бұрын
I have a Zip brand 3 heat controller that looks like it has all the same components as yours inside but different layout with cables going into each end of the PCB. My problem is the neon only comes on with low heat, it goes off on medium and high although the blanket heats up on all 3 settings. I've cleaned the slide switch contacts, replaced the neon, measured all the resistors and diodes all OK and I can't see much else to check? Does anybody have any ideas please?
@lichabhoclosecorporation13802 жыл бұрын
Thanks!
@SuperMixedd2 жыл бұрын
what's the output voltage?
@naaelahholland6403 Жыл бұрын
How do you wash this blanket ?
@Unicorns6 жыл бұрын
Just turn the blanket over and use the same switch
@nivek5031
4 жыл бұрын
Surely you are a Rocket Scientist. :)
@lellandreleedevilliers92624 жыл бұрын
Did you just rip out that white cut out thing and soldier the other one in? Were can i find that whute thing because i dont have another controller
@jeteon
4 жыл бұрын
Same boat hey. From digging around it seems to be a PTC thermistor. I'm not sure yet where to get one that matches the spec though.
@mzendera
4 жыл бұрын
Did you guys come right.I have 3 blankets I'm not using and 1 that just stopped working as well and would live to be able to replace that part
@jeteon
4 жыл бұрын
I was wrong before. It's actually a thermal fuse. I found the datasheet for them: www.setfuse.com/product/over-temperature-protection/thermal-cutofftco/axial-shape/h-series.html. I'm struggling to find the exact model but some of the local electrical shops seem to have something similar.
@tyros202
4 жыл бұрын
Try AUPO 102 C P1F 2A 240 V
@sylviaholburn84593 жыл бұрын
Good morning Jan where are you located
@martinemmerich16164 ай бұрын
DANGER: YOU MUST USE THERMAL PASTE WHEN REPLACING THE THERMO FUSE ! Dear Jan, nearly cool video, but you forgot the white stuff which has a meaning! I have the same controller with a different blanket sold in Germany. I also found the thermo fuse to be blown and also saw the white stuff you called glue. But it's not so sticky, right? I figured out that it is thermal paste which belongs to the safety system! They want the thermo fuse to blow when the resistors next to it get too hot because of too much current flowing! That could happen due to some short circuit that would overload a part of the blanket that's going to get too hot then and might ignite if the fuse doesn't see the warmth an doesn't do its job!
@vinodattri13364 жыл бұрын
Sir thermal fuse work as a fuse or like a auto cut?
@JanDuToit
4 жыл бұрын
Thermostat switches on and off as the temperature fluctuate. The thermal fuse blew once the temp reached a certain point and stayed off.
@vinodattri1336
4 жыл бұрын
How make a auto cut electric blanket switch?
@vinodattri13364 жыл бұрын
What is the difference between thermal fuse and thermostat
@rolandbotes5573
4 жыл бұрын
Thermostat controls the temperature. Thermal fuse breaks the circuit if the temperature rises above a certain setting.
@Margarinetaylorgrease
3 жыл бұрын
Thermostats can go short circuit and so are not a safety device.
@johanlagrange51827 жыл бұрын
Middag Jan ek nodig om kontak met jou te maak tov QDK11-D
@JanDuToit
7 жыл бұрын
Johan La Grange jandtoitx10@gmail.com
@mzendera
4 жыл бұрын
@@JanDuToit Hi Jan...thanks for the video.Do you know where we could get the replacement part? I have 4 blankets that I could potentially start working again...
@mohammedzaheeressack43
4 жыл бұрын
Also looking for the part? You can get the controller alone from Stingray but they half the price of a new blanket.
@edwinmagerstein8035
2 жыл бұрын
@@mzendera Hi I know this is more than a year old but you can try Mantech electronics In Johannesburg
@vinodattri13364 жыл бұрын
Pls reply
@eyaelmaloma10303 жыл бұрын
You were to explain the four cables , u only explaind life and negative.
@ADblog-kv7pp4 жыл бұрын
Covert Hindi 😁😁
@farzana60483 жыл бұрын
Not really helpful. You're just replacing from another control, may as well buy a new control. I need both sides to be warm
@radiorob
2 жыл бұрын
Order a replacement 102 C 250 Volt Axial thermo fuse from Rabtron Vereening. About R12
Пікірлер: 50
That thermal fuse did not burn out for no reason. The heating cable must be damaged somewhere. This cable consists of two wires, external and internal, similar to a coaxial cable. When the cable overheats, a short circuit is made between these wires, the two resistors start to heat up and then the thermal fuse burns.
thank you for this.was about to trash 4 new controllers and the blankets as i couldnt figure out what was wrong
I had the exact same problem and also traced it to the thermo fuse in the controller. Mine is also the queen size blanket. I purchased an exact replacement from a mail order electronic supplier in Vereeniging for about R12 and soldered it in, applying more of the white heat sink compound. I took the precaution of moving the good controller to the opposite side of the bed and the repaired controller to my side. When I switched the repaired controller on it worked perfectly but when my wife switched her side on the thermo fuse blew shortly afterwards in that controller indicating a problem was on her side of the blanket. We have only used this blanket for 2 winter seasons.
@vimal32
Ай бұрын
Shes hotter than you 😂
Top Man :) and keep up with the videos you helped me save my controller
Thank you so much, really helpful.
thanks for the good info.
Nice video buddy. Why don't they put a reset button on cut out? People just throw away blanket and controller... Just a thought:)
Hi there I have the same blanket & having a issue where the light comes on but not getting warm. I messured the thermal fuse & it shows 0.2 should I replace.
Hi i tested the thermal fuse and it was good and also checked 240V on the output side of the fuse and it was there. All diodes test good- no other electronics on this one, but i have 4 wires from the blanket and no matter what combination i try i get at min is a few thousand ohms?? does that mean the coils in the blanket have had it as i noticed the little light sometimes come on and not although the blanket did heat , now i get nothing on any setting and no light or warmth on blanket. Thanks
Good job thanks
How much électricity does it take if used a whole night ?
How much électricité does it take for a whole night heating ?
Mine switched on but it's not heating up. What could be the problem?
Howdy! I have the king size one and a queen and the switches are not moving up or down the controllers? Do you have an idea for me? One side of the King works but with major force to get the button to move into position 1,2 or 3. The other side doesn't want to move at all. The queen has both sides not moving on the controller. It's like it stuck!?
How do you replace the Fuze if it blew up?
Hi, stupid question.... But need to know. Do you guys just replace your electric blankets when they need to be cleaned Or.......how do you clean 'em?
Who repairs these switches in and around Randburg area ?
I am having the same issue , I have opened mine and found the same sticky like white thing around those thermostats, how much must i pay for it to be replaced ? Estimation please
I have a Zip brand 3 heat controller that looks like it has all the same components as yours inside but different layout with cables going into each end of the PCB. My problem is the neon only comes on with low heat, it goes off on medium and high although the blanket heats up on all 3 settings. I've cleaned the slide switch contacts, replaced the neon, measured all the resistors and diodes all OK and I can't see much else to check? Does anybody have any ideas please?
Thanks!
what's the output voltage?
How do you wash this blanket ?
Just turn the blanket over and use the same switch
@nivek5031
4 жыл бұрын
Surely you are a Rocket Scientist. :)
Did you just rip out that white cut out thing and soldier the other one in? Were can i find that whute thing because i dont have another controller
@jeteon
4 жыл бұрын
Same boat hey. From digging around it seems to be a PTC thermistor. I'm not sure yet where to get one that matches the spec though.
@mzendera
4 жыл бұрын
Did you guys come right.I have 3 blankets I'm not using and 1 that just stopped working as well and would live to be able to replace that part
@jeteon
4 жыл бұрын
I was wrong before. It's actually a thermal fuse. I found the datasheet for them: www.setfuse.com/product/over-temperature-protection/thermal-cutofftco/axial-shape/h-series.html. I'm struggling to find the exact model but some of the local electrical shops seem to have something similar.
@tyros202
4 жыл бұрын
Try AUPO 102 C P1F 2A 240 V
Good morning Jan where are you located
DANGER: YOU MUST USE THERMAL PASTE WHEN REPLACING THE THERMO FUSE ! Dear Jan, nearly cool video, but you forgot the white stuff which has a meaning! I have the same controller with a different blanket sold in Germany. I also found the thermo fuse to be blown and also saw the white stuff you called glue. But it's not so sticky, right? I figured out that it is thermal paste which belongs to the safety system! They want the thermo fuse to blow when the resistors next to it get too hot because of too much current flowing! That could happen due to some short circuit that would overload a part of the blanket that's going to get too hot then and might ignite if the fuse doesn't see the warmth an doesn't do its job!
Sir thermal fuse work as a fuse or like a auto cut?
@JanDuToit
4 жыл бұрын
Thermostat switches on and off as the temperature fluctuate. The thermal fuse blew once the temp reached a certain point and stayed off.
@vinodattri1336
4 жыл бұрын
How make a auto cut electric blanket switch?
What is the difference between thermal fuse and thermostat
@rolandbotes5573
4 жыл бұрын
Thermostat controls the temperature. Thermal fuse breaks the circuit if the temperature rises above a certain setting.
@Margarinetaylorgrease
3 жыл бұрын
Thermostats can go short circuit and so are not a safety device.
Middag Jan ek nodig om kontak met jou te maak tov QDK11-D
@JanDuToit
7 жыл бұрын
Johan La Grange jandtoitx10@gmail.com
@mzendera
4 жыл бұрын
@@JanDuToit Hi Jan...thanks for the video.Do you know where we could get the replacement part? I have 4 blankets that I could potentially start working again...
@mohammedzaheeressack43
4 жыл бұрын
Also looking for the part? You can get the controller alone from Stingray but they half the price of a new blanket.
@edwinmagerstein8035
2 жыл бұрын
@@mzendera Hi I know this is more than a year old but you can try Mantech electronics In Johannesburg
Pls reply
You were to explain the four cables , u only explaind life and negative.
Covert Hindi 😁😁
Not really helpful. You're just replacing from another control, may as well buy a new control. I need both sides to be warm
@radiorob
2 жыл бұрын
Order a replacement 102 C 250 Volt Axial thermo fuse from Rabtron Vereening. About R12
Useless , my light is on but no heat.
@unstoppableExodia
2 жыл бұрын
I’m getting this problem as well