Excellent and informative video, thanks! Not sure if you have seen it, but Martyn Davies has also done a great video showing how to control it through software on an Arduino, too....so this can be a very useful module.

@robojax

5 жыл бұрын

You are welcome.

Great video do you have a video using / controlling the xy-lpwm or xylpwm3 using the TX and RX pins?

I am the first to like. Just bought this module last month. Don't have the time to try it.

@robojax

6 жыл бұрын

Thank you very much.

Will the set frequency and duty cycle for both channels individually remain the same even after the power supply is removed? or it gets reset once the power supply is removed.

Thank you for the nice video. Whi 2 pairs of inputs and 2 pais of outputs?

Thank you for the information. it seems in my city does not exist (PMW) Generator With this display

@robojax

6 жыл бұрын

I got it from eBay. you can get it from AliExpress.com or eBay.com, DX.com

@poerwojadoel7992

6 жыл бұрын

tabk u Mr Robojax

Great video, thanks! Can a signal generator perform the same duties as this PWM device?

Hi. Is the 12V and GND wire directly connect to the fan? And just blue wire (pwm cable) connected to the pwm module?

@robojax

4 жыл бұрын

Hi, it needs 5V. 12V will kill it.

Thanks for the video. I have a question about the unit. I can not seem to get the output the same voltage as the input. I can only get a oscillation of around 1.5V irrespective of the input voltage. Is my unit faulty or am I doing something wrong. Thanks Joe

@robojax

2 жыл бұрын

hi, if the output is the same as the input, then the power mosfet or power chip is dead.

How could I vary the duty cycle based off a automotive style temp sensor/switch BMW etc? So I could send the preset pwm signal to a fan motor controller.. 128hz or around there is what the controller is set for from factory.

@robojax

5 жыл бұрын

This can't be controlled. However you can do it with Arduino separately without this module.

@freshkryp69

5 жыл бұрын

@@robojax Ok I understand.. But in controlling the fan rpm, do I use the ground thats next to the pwm output? thanks!!

I was curious if these 2 pwm signals are in the same phase or they are 180 opposite? I mean one signal is showing 5v the other signal showing 0, than it reverses?

@robojax

Жыл бұрын

They are the same

@vahagnmelikyan2906

Жыл бұрын

@@robojax how can I make AC(changing polarity signal with pwm for AC inverter, (no sinwave just square)?

Hola cual es el ci que controla el duty y la frecuencia? Gracias

if i move arm of servo will duty cycle on display change or is it only changing duty cycle moves servo arm but no vise versa.

@robojax

6 жыл бұрын

It doesn't detect the position of servo or anything. It just sends the signal out. Does not read from outside to display it.

@CrazyHHO19

6 жыл бұрын

Robojax thank you for your reply

I just got some of these modules with the same model number on the back, and they're junk because the LCD is basically illegible. They're essentially blank from straight on, and only at extreme angles do you get any usable contrast at all. I have a previous batch that also sucks from straight on, but if you look up at it from about 45 degrees below, the digits are clear. Obviously that's still useless if the display is mounted in something. Generally these seem to suck. There are LED ones, but they have only one display for all functions and it's not clear how they indicate what you're adjusting or what the default display is.

Hi! Great explanation. I have a 5-55V PWM speed controller that is used for controlling a DC motor 12VDC, and I want to use a e-bike throttle with it. From the PWM controller, there is a control input for 5V, Ground, and Signal (Red, Black, & Yellow) and on the e-bike throttle there is the same 3 wires for throttle control. When hooked to the PWM Controller with the e-bike throttle currently, the motors turn slightly and there is .9VDC measured between the signal wire and the ground wire of the control wiring. I think this is because the e-bike throttle uses a hall sensor and operates on 1-4V control signal while the PWM was originally using a 100K ohm potentiometer that is looking for 0-5V. I am not worried about the top end of the voltage, just want to stop the motors from turning automatically and need to use the e-bike throttle. Can you help with this?

@thebeachmule

11 ай бұрын

Or *will this device work for that application?

When the power is disconnected,nd then connected, is the device resetted, or does it restart with the frequencies previously set?

@robojax

4 жыл бұрын

I am sorry for late reply. I was on vacation. I have not tested it but it should keep the settings. the est way to know is to just try it if you have it in hand.

hi; I want to mimic the channel A and Channel B on a CNC MPG , these MPG output a square wave on each click on the wheel , as this device that you are showing has 2 independent channels I wonder if I can use it for my purpose , and if so can you please tell me how I can select the output 2 so I can set it up? thank you Mariano

@robojax

Жыл бұрын

Hi, this does not have two channel. I have explained. they just put extra pins for PWM and for GND. if it had two channels they should have been labeled as PWM1, PWM2 etc.

@robojax

Жыл бұрын

here is dual channel PWM s.click.aliexpress.com/e/_DecBx8R you can select different product from this page

@marianodiaz461

Жыл бұрын

@@robojax thank you, but as it’s usual with products coming from that part of the World , the specifications are not very clear , and if you look at the pictures, like I did , you can order a item that is not fitting to your purpose..

@robojax

Жыл бұрын

I understood that you need two different PWM, so follow the link and purchase it.

This board have on off switch for the pwm signal?

@robojax

2 жыл бұрын

If it has you should see it in video.

Hi, how to use this in metal detector? Thank you.

@robojax

2 жыл бұрын

Hi, this is a signal source and I am not sure how your metal detector works.

hi there. can we use this to control the speed of stepper motor?

@robojax

5 жыл бұрын

Yes. this is what it is made for.

@khyrdynkhyrdyn8505

5 жыл бұрын

@@robojax yap but please show the wiring diagram. I've seen someone using this stuff and using tb6560 driver. how about using l289n?

@robojax

5 жыл бұрын

I watch the video making sure I did not miss the wiring. The wiring has been explained and shown in the video. Please watch it and you can draw it if you need it. You can feed in (connect) the PWM of this to anything you want. Here is an example where PWM module is driving a motor. You can use this module instead kzread.info/dash/bejne/ZZ97utejfZa6edo.html

@allaz3898

4 жыл бұрын

@@khyrdynkhyrdyn8505 have you tried To use this lcd pmw with l298n? Thanks

Can I use this for brushless motor?

@robojax

3 жыл бұрын

oh, I missed to test brushless motor. yes you can see it used with another tester kzread.info/dash/bejne/aaKp2MSBpa-7ZpM.html

Hola, cual es el voltage de la comunicación de TXD y RXD? Gracias | Hello, what is the communication voltage of TXD and RXD? Thanks

@robojax

2 жыл бұрын

Hello, it is the same as the power supply you connect to this.

Can we use this to control mosfet?

@robojax

3 жыл бұрын

If you need PWM , then yes. But each imager has its own characteristics and not all of them will turn ON or OFF with the same voltage.

My dear brother, I need a pwm circuit with a variable frequency from 1Mhz to 5Mhz. I hope you will help me to draw a circuit diagram. Or I want to buy it, but I do not know from any store, please help me for the importance and you my sincere greetings

@robojax

4 жыл бұрын

5Mhz is very high. You need to get Function Generator from eBay or AliExpress www.ebay.ca/sch/i.html?&_nkw=funciton+generator+&_sacat=0

There is 2 channels, why you do not use both?

@robojax

5 жыл бұрын

at 00:39 (click 00:39 to see it) I have explained and at 1:15 I have soldered. This is just ONE channel. They put extra pins for the same channel.

@ivan868

5 жыл бұрын

Ok, understand. Thanks.

What does 74% in the second line means??

@robojax

4 жыл бұрын

I have explained it. 100% means full speed of motor. and 75% is also the speed value. from 0 to 100%

@andreasparasxos5372

4 жыл бұрын

@@robojax thank very much...you sugest to let it near 75%?

We can use it as a long range locator ..to transmit gold frequency or any metal Then we need a receiver ckt to have the returned frequency from gold😍

For those of you that have 3d printers I have created a case for this device here: www.thingiverse.com/thing:2863707

@robojax

6 жыл бұрын

Nice work.

IFOOD

@robojax

3 жыл бұрын

?

you are doing Good.i need your mail id

@robojax

6 жыл бұрын

Thank you. You can contact me via robojax.com contact page.

@sksahadatali4410

6 жыл бұрын

ok mate