How to work with assembly component placements for 3D Contacts #creo #creoparametric #creotutorial #tutorial #4kside #vpalffy #vladimirpalffy
Жүктеу.....
Пікірлер: 17
@yongg123Y6 жыл бұрын
good job.
@bjpastoor7 жыл бұрын
Is there anything new in Creo 4 related to 3d contact? I once tried to set up some domino stones that would tip over after eachother but I couldnt get it to work in previous Creo versions.
@4kside
7 жыл бұрын
Hi, I have tried Domino vs. 3D contact in Creo 2 and Creo 4 - and is work for me. Try it one more time :)
@zakaryaloubar16755 жыл бұрын
Hello, how can we do the 3D contakt when we have a lot of balls ? there are something to minimize the steps because it's the same with every ball or we should repeat it for every one all the contacts. Thank you
@4kside
5 жыл бұрын
Try to place one ball into assembly and make pattern. Apply 3D contact and try to pattern this feature. Note: I don't know if it will be possible, I hope that yes ;)
@muhammadusama36264 жыл бұрын
from which option in creo i pickup the object (actually i want to design the robotic arm with pick and place)
@4kside
4 жыл бұрын
Hi, I do not think that is possible to pickup objects.
@adnanalrefaie99072 жыл бұрын
Hello, I have a question. I have to make a kinematics model of a quadruped robot with Creo. Which references must be between the robot and the floor so that the robot can walk on the floor? Thank you
@4kside
2 жыл бұрын
Hi Adnan, I will try to use cam connections. Bottom surfaces (curves) can align with bottom surface and sometimes lift off when needed.
@adnanalrefaie9907
2 жыл бұрын
@@4kside thank you very much. I will try it 👍
@UA-mk4nh2 жыл бұрын
Hi sir, I hope you will be fine. I have a question that how can we make 3D contact between flat surfaces. I want to make a connection walls of one rectangular box sliding inside another rectangular box (fixed). I did analysis while applying a slider connection on sliding box but I want to do with 6DOF connection which requires 3D connection between walls. Please suggest me a solution.
@4kside
2 жыл бұрын
Thanks for your question, I will try to find some example. Stay tuned. Vladimir
@UA-mk4nh
2 жыл бұрын
@@4kside Ok sir
@4kside
2 жыл бұрын
3D contact between flat surfaces kzread.info/dash/bejne/Zo1t0MaYiLTgo7A.html Stay tuned and thanks for your question.. Vladimir
@dilllibabuk54145 жыл бұрын
Pls demo door open & close
@mundo015 жыл бұрын
why this hard so much than solidworks.
@TheDazzler420
3 жыл бұрын
because this works like reality, real world physics, and behaviour based on nature of materials, Animation part is very hard.
Пікірлер: 17
good job.
Is there anything new in Creo 4 related to 3d contact? I once tried to set up some domino stones that would tip over after eachother but I couldnt get it to work in previous Creo versions.
@4kside
7 жыл бұрын
Hi, I have tried Domino vs. 3D contact in Creo 2 and Creo 4 - and is work for me. Try it one more time :)
Hello, how can we do the 3D contakt when we have a lot of balls ? there are something to minimize the steps because it's the same with every ball or we should repeat it for every one all the contacts. Thank you
@4kside
5 жыл бұрын
Try to place one ball into assembly and make pattern. Apply 3D contact and try to pattern this feature. Note: I don't know if it will be possible, I hope that yes ;)
from which option in creo i pickup the object (actually i want to design the robotic arm with pick and place)
@4kside
4 жыл бұрын
Hi, I do not think that is possible to pickup objects.
Hello, I have a question. I have to make a kinematics model of a quadruped robot with Creo. Which references must be between the robot and the floor so that the robot can walk on the floor? Thank you
@4kside
2 жыл бұрын
Hi Adnan, I will try to use cam connections. Bottom surfaces (curves) can align with bottom surface and sometimes lift off when needed.
@adnanalrefaie9907
2 жыл бұрын
@@4kside thank you very much. I will try it 👍
Hi sir, I hope you will be fine. I have a question that how can we make 3D contact between flat surfaces. I want to make a connection walls of one rectangular box sliding inside another rectangular box (fixed). I did analysis while applying a slider connection on sliding box but I want to do with 6DOF connection which requires 3D connection between walls. Please suggest me a solution.
@4kside
2 жыл бұрын
Thanks for your question, I will try to find some example. Stay tuned. Vladimir
@UA-mk4nh
2 жыл бұрын
@@4kside Ok sir
@4kside
2 жыл бұрын
3D contact between flat surfaces kzread.info/dash/bejne/Zo1t0MaYiLTgo7A.html Stay tuned and thanks for your question.. Vladimir
Pls demo door open & close
why this hard so much than solidworks.
@TheDazzler420
3 жыл бұрын
because this works like reality, real world physics, and behaviour based on nature of materials, Animation part is very hard.