Thanks for sharing.

Hello friend! Thanks for the video, nice work! I have a question, what cable do you use, how much is AWG?

Tq for this infomative video boss

Hi, where will be the charging terminal for this set up to charge the battery ? Is it the input terminal as well?

Fantastic idea

@ntcideasinfo2157

3 жыл бұрын

Thanks for pupport bro✌💞

Very useful

That's cool!

@ntcideasinfo2157

3 жыл бұрын

Thanks for pupport bro

Nice product

thanks !

That Right...!!!

Very interrasting 👍.

Hi, the TP4056 module has ( DW01A and 8205A) can we just include multiple 8205A's to TP4056 and eliminate an additional cost for bms in a battery management system.

@ArcAiN6

7 ай бұрын

no. The module you're referring to is for a single cell only. If you wish to connect multiple cells at the same time, you will need a multi-cell module that has cell balancing.

So nice

Question: how to wire when on the same time: charging and a load connected????

Is it possible, 1 BMS 1S for 2 or more batteries? Thanks.

Here before the "who got recommended comments" I got recommended this

Awesome 🤩 Idea

@ntcideasinfo2157

3 жыл бұрын

Thanks for pupport bro💞❤❤❤

Hello! I added PCB protection board to a 18650 battery but it won't charge.. do you know what may be the reason?

Hello, can four cell phone batteries be charged in series with this bms, or what should I use to charge it?...

can we make a pack with these?

Can you use these under a BMS module that manages a group of 6 of them or so for example, or will it interfere with the larger bms?

@Suzuki_Hiakura

Жыл бұрын

I was wondering the same thing. I bought a large pack of lipo batteries (the flat pouch like ones you use in rc drones and cars) and they all have pre-installed bms boards. They are good boards with a temperature sensor connection and I have been looking into this exact question wondering if I could make a battery pack with them in parallel as I would think it would be the same as putting a fuse on 18650 cells.

can we connect it in series?

I used a bms on a tp 4056 charger and it works well.

@genmckoy

Жыл бұрын

Can Bms alone charge without Tp4056 with dc source of 6-12V?

Hello sir, can i use that 1s 3a bms on 3 pcs. of 18650 2600mah battery?..

Can this act / replace a tp4056?

If we want to connect it with a solar 3W 6V 3A then

What volt input?

Hi shouldn’t the bms allow charging up to 4.2v before shutting down?

@SoriPop

10 ай бұрын

Depends on the battery and BMS model

3:13 What do you mean battery recovers itself? turning a connected device on and off might be damaging....!!

@terrence2209

2 жыл бұрын

Power consumption, the power is too low the protection board will be powered off, the power off process is in a state of no power consumption, the power will be increased to cause the protection board to think that the power is enough, so it starts to open the power supply again

Can I make 1s 10p?

Master, how can I do 2s bms in parallel connection, please reply, thank you

@CreativeAndDuck

2 жыл бұрын

Can you describe it in more detail?

@research_ai8740

2 жыл бұрын

@@CreativeAndDuck hey I have a question about this protection, I have a 4cells in parallel and then in serie (total voltage is 12.6v 25000mAh )do I need to put this protection on each cell?

Can this 1s bms be used in 3 18650 in parallel?

@Suzuki_Hiakura

Жыл бұрын

It could, so long as it's parallel that is. You should try to limit how many you put in parallel though as when one fails the others will start putting power into the failed one and start a fire or explode... that's why you use those nickle fused sheets (after too much current passes into a dead cell it breaks the fuse to avoid explosions and fire). Still is somewhat dangerous; I recommend doing thorough research into the topic regardless to avoid issues and injuries as well as to minimize potential hazards.

you can crank that up to 10KV and it wouldn't matter, as you pushing 0.00A No amperage, no power

@Hyxtryx

4 ай бұрын

Not true at all. Something has to detect that the voltage is too high, and that something would have to be able to withstand 10KV. It could also arc across solder points. That board is not designed to withstand 10,000 volts.

Can i use 1s bms for 2 batterys

@aravinththamilarasu3565

2 жыл бұрын

You can but the charging time will be more. If that is not a problem you can. for one battery if it takes one hour then it might take two hours as there is a max limit of 1A.

can we use 1s bms in series connection with other same 1s bms?

@deepaknanda1113

Жыл бұрын

Yes...should of more ampere (4056 is 1Amp)

Can it (1s BMS) be used in multiple 18650s battery connected in parallel (ie power bank)?

@thevlog3653

Жыл бұрын

No

@pepeg1954

Жыл бұрын

@@thevlog3653 how about only 2x 18650?

@srisairampraveenganisetti

7 ай бұрын

Yes get an high amp one like 5amp

Si uso una tarjeta BMS puedo cargar la batería con un cargador de 5V

Input voltage? Can I charge with 5v usb charger?

@aravinth007vt

Жыл бұрын

Yes you should be able to. 👍

How to shop ing and links and send me please

Bossing pano yung apat n battery nka parallel alen po pwede..

Hi, greetings and salutations from Mexico. This video was very interesting for me and the question I want to ask is as follow: I need to replace the batteries of an Emergency lamp which it's always connected to the electricity and the batteries start working when the electricity is cut off and the light is turned on. . Could the circuit showing here be good to protect any damage ?, I mean that the battery may explode due to continous connection to the electricy. I appreciate your comments, and thank you very much in advance.

this cercuit model code no?

Can you make series battery demonstration with this tiny bums board?

Can this be connected to charge 2s, 7.2/8.4v?

@as424100

Жыл бұрын

You can buy a 2s BMS, you can not use this one for that purpose. If i'm not wrong yhere is 1s(like this one) 2s and 3s BMS, you can buy them on aliexpress relatively cheap

@jamesallen6007

Жыл бұрын

Thank you.