Thank you for the quick and detailed video without twenty minutes of unnecessary intro. ; )

@AroundTheHome1

2 жыл бұрын

So glad to help! Thank you for watching. Check out hundreds more of our videos at www.aroundthehome.org

Thank u so so so much … you have no idea how much I appreciate the advice… I couldn’t figure out how to connect elbows without cutting them in the corners… saw you’re Awesome video and all was good after

@AroundTheHome1

11 ай бұрын

You are so welcome!

Finally, a DIY video that I didn’t have to speed through... because you did it for me. This was perfect, thank you.

@AroundTheHome1

6 жыл бұрын

Glad you liked it. For more great videos check out my website www.greatwhiteninja.com

Very good concise clear video without the usual filler you see in most how to videos. Thanks.

@AroundTheHome1

3 жыл бұрын

Glad it was helpful! Thank you for watching. Check out hundreds more of our videos at www.aroundthehome.org

Thanks Nathan! What a great detailed, step by step video. That’s what I’m doing today. 👍✌️

@AroundTheHome1

6 жыл бұрын

Awesome, glad I could help.

Loved how you didn't waste our time and used speed-ed up video and voice over. Great job!

@AroundTheHome1

5 жыл бұрын

Thanks for watching. Don't forget to stop by our website www.greatwhiteninja.com

I’m learning something new watching you work, nice job.

@AroundTheHome1

3 жыл бұрын

Glad to hear it! Thank you for watching. Check out hundreds more of our videos at www.aroundthehome.org

This is exactly the type of video I was needing to fulfill my project! Thank you!

@AroundTheHome1

Жыл бұрын

👍 So glad to help! Thank you for watching. Check out hundreds more of our videos at www.aroundthehome.org

Gutters and downspouts are easy. As long as you aren’t scared of heights and can carry/climb 32-40ft extension ladders with/without standoffs, can drive a nail and read a tape...You’re golden 🙌🏻 I’m a gutter guy, guy. Lol. Also, knowing how to use a metal brake is useful too (flashing). Great video!

I was a little confused when you cut the part to fit into the second elbow that looked like a B-style one, but I see you put the A style elbow and saved the B for the bottom turn. Thanks so much for showing the can-opener style drop-cut to the gutter. I'm going to share this video!

@AroundTheHome1

Жыл бұрын

👍 So glad to help! Thank you for watching. Check out hundreds more of our videos at www.aroundthehome.org

Thanks for teaching a great trick, not having to use the silly insert to attach the gutter is fantastic. It makes sense not to use a gutter insert, since the lip of the insert is above the water level and it leads to gravel accumulation. Your method allows for water to go where it wants to go, downhill!

@rob4121

Жыл бұрын

Yes, I wish I saw your video where you did this, alas I used a holesaw

@maxmanx1294

Жыл бұрын

Attaching the elbow to the gutter's cut down tabs frequently leads to ripping the aluminum gutter at some point. I understand about the outlet tubes affecting roof gravel drainage. I try to build a gentle slope using my sealant. In some areas, code mandates use of the outlet tubes.

@seeharvester

Жыл бұрын

I've seen water go uphill.

DUDE!! That background music is my jam!!! Great video.

@AroundTheHome1

4 жыл бұрын

Glad it helped! Thank you for watching. Check out hundreds more of our videos at www.aroundthehome.org/

Great vid, I was thinking why outside the box, thanks for reeling me in.

@AroundTheHome1

5 жыл бұрын

Thanks for watching, and I am glad to help. Don't forget to stop by our website www.greatwhiteninja.com

Great explanation seems simple but few things are I have to put up a couple gutters in my home this videos helps a lot.

@AroundTheHome1

5 жыл бұрын

Thanks for watching. Don't forget to stop by our website www.greatwhiteninja.com

Brilliant idea to attach the elbow to the gutter. I follow this and am so happy that I did because I have no access from the above 2-story gutter during the addition. I drill a hole and then cut the diagonals instead as the older gutter is way to tough. Thanks so much!

@AroundTheHome1

4 жыл бұрын

Thanks for watching and don't forget to stop by our website for many more helpful videos. www.greatwhiteninja.com

@Phoenixrising8313

2 жыл бұрын

What size hole do you drill??

Clear and easy presentation. Good video. Thanks!

@AroundTheHome1

6 жыл бұрын

Glad you liked it. For more great videos check out my website www.greatwhiteninja.com

Excellent presentation. Straight to the point

@AroundTheHome1

5 жыл бұрын

Thanks for watching. Don't forget to stop by our website www.greatwhiteninja.com

good tips and easy to follow! Thanks

This video was pretty helpful!

@mshelton26

7 жыл бұрын

Carl Arg

Great video -- content and speed. Very helpful.

@AroundTheHome1

2 жыл бұрын

Glad it was helpful!

As a casual observer/non-professional plumber who has had many plumbers input, the one thing I would change to this approach, is that I would create an air-gap between the down-pipe running vertical along the house, and the pipe on the ground, meaning, putting a grated drain or a sump at the bottom, this allows water to flow at all times, even if there is something clogging the downpipe, it also allows debris to fall out of the downpipe onto the grate/sump, then from the sump/grated drain, I would continue the pipeline as you have.

Nice DIY, smart and good craft!

@AroundTheHome1

3 жыл бұрын

Thank you! 😊 And thank you for watching. Check out hundreds more of our videos at www.aroundthehome.org

Thank you for the knowledge drop. Just what I needed to know without the incessant blathering.

@AroundTheHome1

4 жыл бұрын

Thanks for watching and don't forget to stop by our website for many more helpful videos. www.greatwhiteninja.com

Very concise and well done. Thanks!

@AroundTheHome1

6 жыл бұрын

Thank you, glad to help.

Simple straight forward. Good vid Thanks

@AroundTheHome1

4 жыл бұрын

Glad to help. Thank you for watching, and please share. Check out hundreds more of our videos at www.aroundthehome.org/

Now that's a "how to" video. Well done.

@AroundTheHome1

2 жыл бұрын

👍 So glad to help! Thank you for watching. Check out hundreds more of our videos at www.aroundthehome.org

Sweet, that will be my next week-end project..

@AroundTheHome1

4 жыл бұрын

Thanks for watching and don't forget to stop by our website for many more helpful videos. www.greatwhiteninja.com

Thanks! Exactly what I wanted to know.

@AroundTheHome1

4 жыл бұрын

Thanks for watching and don't forget to stop by our website for many more helpful videos. www.greatwhiteninja.com

Awesome tips, I like the x in the bottom of the gutter to attach the downspout, I’ve been using the plastic attachments, and they suck.

@AroundTheHome1

5 жыл бұрын

Thanks for watching. Don't forget to stop by our website www.greatwhiteninja.com

THANKS! You saved me some money. I can do this!

@AroundTheHome1

4 жыл бұрын

Thanks for watching and don't forget to stop by our website for many more helpful videos. www.greatwhiteninja.com

Great Video, Thanks For The Video.

@AroundTheHome1

6 жыл бұрын

Awesome, glad that you liked it.

If you measure the soffit from the wall to the outer edge of the fascia and then take off four and a half inches that is how long you will cut the piece of pipe that goes from elbow to elbow and it will be a perfect pit every time.... Put the elbows together to the Cross arm pipe before attaching it to the gutter

Thank you sir. Just like I figured I would do it. But I usually watch a few videos first.

@AroundTheHome1

2 жыл бұрын

👍 So glad to help! Thank you for watching. Check out hundreds more of our videos at www.aroundthehome.org

Thanks for this. Seems simple enough.

@AroundTheHome1

3 жыл бұрын

Glad it was helpful! Thank you for watching. Check out hundreds more of our videos at www.aroundthehome.org

Dude you made that look easy Now I know where I messed up

@AroundTheHome1

5 жыл бұрын

Thanks for watching. Don't forget to stop by our website www.greatwhiteninja.com

I need to watch and learn ima be working replacing gutter in a couple of weeks.

@AroundTheHome1

4 жыл бұрын

Thanks for watching and don't forget to stop by our website for many more helpful videos. www.greatwhiteninja.com

Drop-ins is where it's at gutter guy.

@jhendrick5526

3 жыл бұрын

Are Drop-Ins just another name for Hood taps? 🤔

Great video, thank you.

@AroundTheHome1

6 жыл бұрын

You are welcome.

great video. Very helpful

@AroundTheHome1

6 жыл бұрын

Glad to help. For more great videos check out my website www.greatwhiteninja.com

This was great thank you!

@AroundTheHome1

Жыл бұрын

You're so welcome!

One final tip I learned from the contractor who installed most of my gutter system. He uses some type of one-inch drill saw to make a one-inch hole at the center of the "X". Then he uses tin snips to cut the legs of the X. Really a great way to do it.

@AroundTheHome1

6 жыл бұрын

That is an interesting way to do it. Any standard hole saw would cut the aluminum gutter. If it is digging in to hard then you can run the drill backwards and get your cutout.

excellent

STRAIGHT TO THE POINT! NICE.

@AroundTheHome1

7 жыл бұрын

Thanks, glad to help.

Nice work!

@AroundTheHome1

5 жыл бұрын

Thanks for watching. Don't forget to stop by our website www.greatwhiteninja.com

Phenomenal video, ty

@AroundTheHome1

3 жыл бұрын

So glad to help! Thank you for watching. Check out hundreds more of our videos at www.aroundthehome.org

Best how to video ive seen for this. THANK YOU!

@AroundTheHome1

4 жыл бұрын

Thanks for watching and don't forget to stop by our website for many more helpful videos. www.greatwhiteninja.com

Wow wonderful job so easy

@AroundTheHome1

5 жыл бұрын

Thanks for watching. Don't forget to stop by our website www.greatwhiteninja.com

I enjoyed the medieval background music

@AroundTheHome1

5 жыл бұрын

Thanks for watching. Don't forget to stop by our website www.greatwhiteninja.com

Great video

@AroundTheHome1

3 жыл бұрын

Thank you for watching. Check out hundreds more of our videos at www.aroundthehome.org

Drop tubes are a good idea for attaching downspout to gutter. Just my opinion.

nice tips, thanks

@AroundTheHome1

5 жыл бұрын

Thanks for watching. Don't forget to stop by our website www.greatwhiteninja.com

Great video sir really appreciate this 👍"new subscriber"

@AroundTheHome1

3 жыл бұрын

So glad to help! Thank you for watching. Check out hundreds more of our videos at www.aroundthehome.org

Easy way to find your piece in between elbows measure the overhang and subtract 5" (5"downspouts ) 6"for 6" downspouts

@richard42vacca94

3 жыл бұрын

it's still subtract 5inch for 3x4 spout

EXCELLENT VIDEO THANK'S

@AroundTheHome1

5 жыл бұрын

Thanks for watching. Don't forget to stop by our website www.greatwhiteninja.com

Thank you brother

@AroundTheHome1

4 жыл бұрын

Glad to help. Thank you for watching, and please share. Check out hundreds more of our videos at www.aroundthehome.org/

thank you so much .

@AroundTheHome1

6 жыл бұрын

Welcome so much. For more great videos check out my website. www.greatwhiteninja.com

Hi Nathan. I got the job done, but had trouble getting the "X" cut with the utility knife even with a new blade. Finally, I had to do a starter cut on each leg with a Dremel rotary saw. Has someone invented a device to cut the "X" perfectly every time with less effort? It seems like a device with two plates, top and bottom, with sharp edges on the bottom and grooves on top, both in the shape of the "X" with a jack screw connecting them would be a wonderful time saver and would make exactly the right length of cuts every time. The jack screw would go through a 1/4 inch hole that would be drilled in the center of where the downspout was to be located. Just turn the jack screw with a handle and it's done! Anyway, it's done and I put plenty of sealer on. Hopefully it'll be watertight next rain or snow. That 1/4 inch magnetic driver was a real aid!

@AroundTheHome1

6 жыл бұрын

I don't know of a downspout hole cutter, but you know it could totally be out there. Thanks for watching. For more great videos check out my website www.greatwhiteninja.com

@christinemcinnis3933

Жыл бұрын

Hey, just watching another video and remembered your comment. In this video they show using a tool to cut the 'x' kzread.info/dash/bejne/qpWIk9h9fsKtcbA.html

Measure the soffit, and height off the wall. Make the A style neck length 4 inches shorter than the length of the soffit to account for the size of what looks like small square elbows in this video, crimp an end,attach the elbows, boom neck is made, make a length 20 inches shorter than the wall crimp in end and add an elbow, now when all is attached the bottom of the pipe will be a little less than a foot off the ground just to be sure it’s not short and can be shortened if to low. Now take an small square outlet, (that I haven’t seen anyone use yet on KZread ) and add a bead of clear silicone caulking Around it under the lip. Trace the inside of the outlet onto the pipe where it is desired with a sharp pencil. Cut out the hole with snips. Pop in the outlet. Pull it snug at two coloured screws under the eaves trough and through the lip of the bracket on each side to get it really snug. The caulking already seals the screws. Check that the prepaid neck a style neck fits well, screw the top on each elbow to. Attach it to the outlet and Make sure it’s strait to the wall aligning with the soffit groves to look very nice. Make a mark on the wall, attach your two straps or three if it’s a tall one, drill and plug if it’s brick. Attach the pipe to the neck add a coloured screw on the hidden side. Wrap your straps screw it in. Add you extensions and you’re done. Secure the bottom elbow with 2 coloured screws and tadda done. Less up and down the latter, less spend 1 hour cutting an x for a hole with a knife no measuring every other stage of this process one at a time and no visible caulking at the outside of the top elbow.

Thanks man

@AroundTheHome1

6 жыл бұрын

No prob, glad to help. For many more great videos check out my website www.greatwhiteninja.com

When using "A"elbows, If you measure from the back of your 5k gutter or faish straight to the wall and subtract 5" you will get the correct length piece everytime.

@AroundTheHome1

4 жыл бұрын

Thanks for the tip. Thank you for watching, and please share. Check out hundreds more of our videos at www.aroundthehome.org/

Thanks!

@AroundTheHome1

6 жыл бұрын

Thanks for watching, and I am glad to help. Don't forget to stop by our website www.greatwhiteninja.com

Awesome 👍👍

@AroundTheHome1

4 жыл бұрын

Thanks for watching. Don't forget to stop by our website www.greatwhiteninja.com

I like the music.. Recorders.. kinda Victorian. 🤙

the music sounds like something from zelda

Hi, video-thanks. I have a question. I'm trying to take apart my downspouts as I have a clog at the bottom. But I can't get these screws off. It doesn't look like a regular screw. It looks circular. Thought maybe an allen wrench would work-nope. Thought maybe I could pry it off with a flat head-nope. Do you have any clue? Is there a standard or special screw for downspouts? I know it sounds silly but I'm clueless how to get this thing off.

@AroundTheHome1

6 жыл бұрын

To my knowledge, at least around here, there are two methods used. A small hex head screw or a rivet. So, I am assuming by your description that you have rivets. They have to be drilled out. Normally a 1/8th in drill bit will do the job. Then you can get some gutter screws to put it back together with. Thanks for watching, and I am glad to help. Don't forget to stop by our website www.greatwhiteninja.com

When putting screw in siding for strap, how do you know the screw won't hit a pipe or wire in the wall? Great video--thanks!

@AroundTheHome1

3 жыл бұрын

No problem, thanks for the question. You just have to use the right size screw. 1 1/4 inch screws are great here. Now if someone was using 3 inch screws, then there is that chance. Thank you for watching. Check out hundreds more of our videos at www.aroundthehome.org

An ice storm ripped my downspout off the house this winter. The eaves-trough no longer has the 4 tabs. What do I do now?

Nathan, what torque setting do you put on your driver to ensure you don't strip out the thread as you put it in>

@AroundTheHome1

6 жыл бұрын

You know honestly I don't use the torque settings but once in a blue moon. I just stop as it gets tight and the brake on these cordless drills does the rest. Thanks for the inquiry and for more great videos on just about everything check out my website www.greatwhiteninja.com

Can I add a downspout hole the the other end of about a 25' gutter so that I can add a rain chain? Thank you, unsure if it will work..

@AroundTheHome1

4 жыл бұрын

Well, without seeing your project I can't be for sure, but it sounds ok. Thanks for watching and don't forget to stop by our website for many more helpful videos. www.greatwhiteninja.com

How do you remove a drain and then patch it with a gutter

Hi Nathan, what kind and what size of screws do you use to attach one downspout piece to another?

@AroundTheHome1

Жыл бұрын

I don't know the specific size, they are just the sheet metal screws right there in the gutter department. They are also color coated to match the different color gutters.

I get it!

@AroundTheHome1

5 жыл бұрын

Thanks for watching, and I am glad to help. Don't forget to stop by our website www.greatwhiteninja.com

When screwing the fastener to the siding, does it matter if it is lined up with a stud?

@AroundTheHome1

5 жыл бұрын

I think you mean rafter, but I know what you are asking. There should be a 1x6 board behind the facia wrap, or just the facia board alone. Long story short, as long as it is not rotten then you can screw anywhere into the facia. Thanks for watching. Don't forget to stop by our website www.greatwhiteninja.com

Is there no gutter adapter needed at the top? I know you just cut it and made an x is that sufficient?

@AroundTheHome1

5 жыл бұрын

No adapter is required. You can purchase one and cut off those flaps that I made in the video and use that to attach the downspout instead if you like. Thanks for watching. Don't forget to stop by our website www.greatwhiteninja.com

You could use a holesaw to cut the hole in the bottom of the gutter for your outlet. Muccccch quicker

Other vids would have us use a jigsaw or tin snip. Razor knife is so streamlined.

@AroundTheHome1

6 жыл бұрын

Thanks, glad to help.

I have an out-building where they left the rafter tails exposed. What should I put up to support gutters? I'm not having any luck finding gutter videos that don't use finished buildings.

@AroundTheHome1

3 жыл бұрын

If the rafters aren't too far apart you should be able to just mount to the ends. Are they 16 inches apart?

@Shalmaneser1

3 жыл бұрын

@@AroundTheHome1 Thanks for writing. I'm surprised that hanging directly off the ends is an option. Closer examination shows the ends are 1/2" back of the paper, which is 1/2" back of the shingles. I'm thinking 1" x 5" fascia after sealing up the weathering ends. Great camera work.

@AroundTheHome1

3 жыл бұрын

It can be an option if they are spaced on 16 in centers and not further out, and if they are the right length. Of course, against a facia board is better and it sounds like that is what you need to get them the right length. I don't have any gutter install videos, but take a look for some so you can see how to line them up. Also, if it is possible to get a drip edge there if you don't have one. Thank you! 😊 And thank you for watching. Check out hundreds more of our videos at www.aroundthehome.org

@Shalmaneser1

3 жыл бұрын

@@AroundTheHome1 Thanks for writing. I have 1/2" between ends & paper, 1/2" between paper & asphalt shingles. Looks like It's set up for facia, they just didn't get to it. yeah, drip edge. You and your people do good camerawork.

@AroundTheHome1

3 жыл бұрын

Good luck with your project, and thank you.

Lol old fat man productions 😂 loveit

@AroundTheHome1

5 жыл бұрын

Thanks for watching. Don't forget to stop by our website www.greatwhiteninja.com

How do yoy get the screws in there so quick/easy? is there a special attachment of your drill? Are they self drilling screws? How do they attach to your drill without you having to hold them? definitelly took me a lot more time to do this

@AroundTheHome1

6 жыл бұрын

Good questions. It was a long time back so I don't know if they were self drilling or not. Honestly the metal is thin enough that just the sharp pointed gutter screws will cut in just fine. Now the bit for the drill, that is the trick. Use a 1/4" hex driver. It will have a magnet in it to hold the screw. This makes the job as easy as it looks.

@slavisagambiroza5436

6 жыл бұрын

ahh ok magnetic hex driver, thats it. Biggest disadvatage of being unexperienced, is not knowing that there is a tool for everything and what ita called. thanks!

@AroundTheHome1

6 жыл бұрын

I have a lot of videos to help you around the home. Check out my website www.greatwhiteninja.com

Could you provide a link to a fabric abrasive blade? I cant seem to find any.

@AroundTheHome1

5 жыл бұрын

Here is an Amazon link for the 10" blade www.amazon.com/DeWalt-DW8005-General-Purpose-Metal/dp/B00004YMCI/ref=as_li_ss_tl?_encoding=UTF8&pd_rd_i=B00004YMCI&pd_rd_r=169d0045-019a-11e9-a088-a167811d1016&pd_rd_w=EyN5E&pd_rd_wg=WZFaL&pf_rd_p=7d5d9c3c-5e01-44ac-97fd-261afd40b865&pf_rd_r=Z9S6J3MK6MJK1T7PECSE&psc=1&refRID=Z9S6J3MK6MJK1T7PECSE&linkCode=ll1&tag=greatwhitenin-20&linkId=fc0fa81cd2dc8329760fe7c7cf3258e3&language=en_US Here is the 12" blade link www.amazon.com/DEWALT-DW8022-12-Inch-Abrasive-Cutting/dp/B00004YMCU/ref=as_li_ss_tl?_encoding=UTF8&pd_rd_i=B00004YMCU&pd_rd_r=7ee10bfc-019a-11e9-ae91-771b90899601&pd_rd_w=3jvo9&pd_rd_wg=4SSB3&pf_rd_p=18bb0b78-4200-49b9-ac91-f141d61a1780&pf_rd_r=2SM2C8W7CA1AT1R618GC&psc=1&refRID=2SM2C8W7CA1AT1R618GC&linkCode=ll1&tag=greatwhitenin-20&linkId=ede85837c73f6956f7a42301cbc2e5e1&language=en_US Thanks for watching. Don't forget to stop by our website www.greatwhiteninja.com

@AroundTheHome1

5 жыл бұрын

Double check the arbor hole is 1" for the 12"blade. I don't have a 12" miter saw so I don't know if there are different sizes.

Good video, but the music sound like it was made for a children's cartoon. Thanks for making this.

@JamesQMurphy

6 жыл бұрын

FWIW I didn’t mind the music at all

I have a question about my downspout connection to my gutters. My downspouts are 3x4, but the cut on the gutter is about 2x2 inches. In addition to this necking down the installer used sheet metal screws that catch all the debris. Flow to the downspout ends up being nothing and I have to clean my gutters about every two weeks. I was wondering if you have any solutions. I was thinking about adding another downspout up the line of the gutter about 5 feet and connecting it to the existing downspout.

@AroundTheHome1

5 жыл бұрын

Ok, I will do the best I can to answer your questions. I am surprised that your opening is only 2x2. If you take your downspout off you can enlarge the opening using the technique that I used here. I used sheet metal screws as well, but mine are for gutters meaning they are not only painted to match, but very short. If longer screws are used, I can see that they would catch everything. If you want to ditch the screws altogether then you can switch to pop rivets. I don't understand your last question. Connect it to the existing downspout? Actually, let me step back here. If your downspouts can handle the water flow from regular rain when they are not clogged, then I would not add more. Just address the problems you have with the small opening and long screws. Then maybe install some sort of leaf guard on them to keep debris from even entering. Thanks for watching, and I am glad to help. Don't forget to stop by our website www.greatwhiteninja.com

@dixoncider7256

5 жыл бұрын

Awesome. Opening the downspout is a great idea. I think I can open it up right from the top and using rivets instead is a good idea to prevent debris from snagging up. Thanks for the help.

@AroundTheHome1

5 жыл бұрын

No problem, good luck with your project.

I hate prefab elbows they look terrible I like to do the downspout looking same texture all the way

Rough and ready...

@AroundTheHome1

2 жыл бұрын

So glad to help! Thank you for watching. Check out hundreds more of our videos at www.aroundthehome.org

Is it possible to bend the downspout so you don't have any joints?

@AroundTheHome1

7 жыл бұрын

I don't know of any tube benders for downspouts. Though that doesn't mean that it doesn't exist.

@randyc5650

7 жыл бұрын

No.

@jessesorenson9988

6 жыл бұрын

Yes you can. I do it every day... it's called a elbow machine

Damn i fucked up on the first part lol did a shitty job cuttin

And it only took 30 mins in fast mo

It's not called a corner it is called an elbow.....

These cheap and nasty gutter outlets are the bane of every homeowner with trees around his house. Why? Because they plug up so easily! The proper outlet is a funnel the full width of the bottom of the gutter and 9 inches long with a 3" x 3" outlet minimum. The transition from 9" to 3" is by inclined sides at 45 degrees. This will resist plugging with most foliage debris.

find someone with a punch. takes about 3 seconds and youre done. but as far as 100 percent DIY with basic tools, this will work

@AroundTheHome1

4 жыл бұрын

Thanks for watching and don't forget to stop by our website for many more helpful videos. www.greatwhiteninja.com

I feel this video may be helpful to the home weekend warrior, but I feel a "pro" would have used better downspout material and soldered the joints or at least cut and formed his own elbows. I feel preformed elbows are for amateurs and not "pros"

@AroundTheHome1

6 жыл бұрын

This is basically a pro tip for the weekend warrior. That being said it is the same method that the Pro Installers use in the south and mid-west for residential gutters. That's where I learned how to do this. I see that you liked a video of a gutter installer soldering his downspouts. I have only seen that method used for commercial application. Maybe where you live that is done for residential, but not around here. Screwing your downspouts together is really helpful with all the trees we have around here in case you need to take it apart for cleaning. Thanks for watching, and I am glad to help. Don't forget to stop by our website www.greatwhiteninja.com

@622mf

6 жыл бұрын

Its only water...