I admire you for figuring it out. We could not get ours going, ordered a replacement pump and it has a sheared off brass bolt right out of the box, Of course we could not tell that it was until it was installed and cranked up and bluey! The bolt head flew off! We're sending it back, get a replacement. I am so sick of that pressure washer. It was my bright idea to try and repair it, now I want to forget the whole thing. :(

@LivetofishOutboardRepair

Ай бұрын

I'm sorry you had trouble. I give you a lot of credit for trying. Thanks for sharing your experience and taking the time to view the video.

UPDATE:1 year and still cranks within the first 2-3 pulls. Probably will buy another when this one finally does bite the dust kzread.infoUgkx43QMbQqu67IZadu9ou8Sg1BdrunMRNqX . No issues at all. Very happy with it.UPDATE: After 6 months of use and over 70 uses I would still highly recommend this pressure washer. It does vibrate a decent amount but never had it “walk” like others have mentioned. No oil leaks, still seems to run like the day I bought it. Still cranks within 2-3 pulls every time. Very happy with my purchase!Have used it about a dozen times now. Plenty of power, cranks up on 1-2 pulls every time. My only complaint would be I wish it was a little taller to make it easier to walk with it (hits my ankles a lot) and that the two hose connections were a little further apart but it hasn’t caused me any issues. Seems to run a good 1-1/2-2 hrs on a full tank, overall a well built machine and definitely worth the money in my opinion.

@LivetofishOutboardRepair

10 ай бұрын

@jeannineslack9992…. Thank you for sharing your experience. I completely agree with your assessment.

You have nothing to be sorry about sir. Haters have to hate. I for one, thank you for the content. And I don't care what anybody says....it's a gosh darn "woodruff key".

@LivetofishOutboardRepair

Жыл бұрын

@61 spindrift… thank you very much for commenting and your support. although he’s right, it’s not woodruff key and I stand corrected.

His terminology is still correct . Woodruff key is older term. Yes they have a rounded end . But it's the same concept, stop shaming the guy for his use of words .

I think its a shear key to save the pump and engine,like you have in snow throwers.

You probably already have your pressure washer fixed by now, BUT OK! Yes i have a TroyBuilt i bought Refurbished from Sears in 2010 AND IT HAS BEEN A GREAT MACHINE!!! Well last year it just went KA PUT on a job i had to finish, So i figured it was time to R & R the pump. When i took the pump off i quickly discovered there was a problem THERE WAS NO KEY. so i figured just go to ACE HARDWARE and pickup a small 1/4 inch X 1/4 inch key square stock, Well when i went to install it the pump STILL turned and was DEFINITELY not ENGAGING with the engine. I was stumped for about 1/2hr. when i finally RELIESED that one side (that engages engine to the pump) HAD TO BE LONGER/THICKER by about 1/16 of an inch to 1/8 of an inch. So i grabbed my mig welder and piled on the material (VERY CAREFULLY) then when i was done i grinded the taller side of the key flat and installed on the shaft, BUTT the key would NOT SIT still when i wanted to install the pump on the engine shaft SO i tack welded the key on the engine shaft. aaaaannnd WA LA the pressure washer finished the job!! and has worked ever since. PRAISE BE TO GOD!!

Awesome video, thank you! Crazy that the key was gone haha

@LivetofishOutboardRepair

3 жыл бұрын

I know right. Never expected that. Thanks for watching and commenting.

@houstonzechariah3094

3 жыл бұрын

dont know if anyone gives a damn but if you're bored like me atm you can stream all of the new movies on InstaFlixxer. Have been streaming with my gf lately :)

@gordoneli3786

3 жыл бұрын

@Houston Zechariah definitely, been watching on Instaflixxer for since december myself =)

At 12:14 you can see that the keyway (slot) on the engine crankshaft has a "mark" in it, near the engine. Looks like the key got loose from wear and walked toward the engine in the keyway. Then it finally got loose enough, and worn small enough, that it finally came out, causing the "mark" in the crankshaft when it left the keyway.

@LivetofishOutboardRepair

Жыл бұрын

@oldbones3092……. Great observation. Thank you for commenting

Pretty sure they'd use a soft aluminum key to protect the pump and engine if the pressure relief system fails and there's a hydrostatic lock. Over the years it probably ground itself to powder as you suggested. Good on you for figuring it out.

@LivetofishOutboardRepair

3 жыл бұрын

Gene Ressler....I’ll bet your right about that the key must have been aluminum. I think the new key is steel ... not sure but it’s been working fine so far. Thanks for the explanation.

@kalebmarquardt8008

3 жыл бұрын

Its possible but....the metal fragment he pulled out in the video appeared to be magnetic. It looked as if it was magnetically sticking to the tip of his scratch ask/ice pick...could've been sticky with grease.

@LivetofishOutboardRepair

3 жыл бұрын

@@kalebmarquardt8008 I guess we will never know

@mikenakano9655

2 жыл бұрын

Negative, keys are steel.

@TheMan-ue7ri

2 жыл бұрын

@@mikenakano9655 keys are steel or aluminum . Check any Briggs and Stratton engine and you will find an aluminum key . Been that way for 40 yrs

they make that key of some short of plastic, so if the water pump fails the gasoline engine will not break it into pieces. like have a soft bolt on your farm plow, cheaper to replace a bolt that a broken arm on a tracktor plow

i think it is the dirt /shavings inside on top of the piston based on what u show.

I’ve never seen one missing the key way, strange thing for sure I’ve rebuilt a lot of them and kits are not that high price I try E replacement parts first

@LivetofishOutboardRepair

Жыл бұрын

Phillip Hall … thanks for the tip. Yea the key was shredded unfortunately I wiped the pump clean and didn’t show the metal fragments but the key was definitely there just in very small pieces.

Had same problem on new pump 2 dollar keyway at tsc

@LivetofishOutboardRepair

3 жыл бұрын

Then you had the same problem I had. Pump was fine just needed a new key way. I’m glade if this video helped you out. Thanks for watching and commenting.

my guess is that whoever used a 3/16" x 1" keystock instead of 1/4" x the length of the slot. so as it shifted it shredded the bar stock. steel key stock won't shred like that but aluminum key stock that will sacrifices the key stock instead of the pump or the motor.

@LivetofishOutboardRepair

2 жыл бұрын

HOPE … I’m not sure what size key the factory used when building this model. I’ve owned it since it was new and never ran into this problem until it just stopped producing pressure. Like you said the key must have been aluminum otherwise it would have shredded the pump.

I put my pump back together today after replacing 3 check valves, that is when I noticed I had no keyway. I was lucky. I had some 3/16 th metal in the shop and made one. Got it together, and water went right through it out these two small channels on the head of the pump. It was getting dark and I was done for the day. Do you have any clue as what I did wrong?

@LivetofishOutboardRepair

Ай бұрын

You may have worn o/-rings

I watch the video about 4 times and see exactly the same pressure washer pump I have and pump unloader stock and I can find a place to buy (completely stock) any suggestions where to buy ,please help

@LivetofishOutboardRepair

Жыл бұрын

@tatatickssantiaguel3771…. I’m sorry but I don’t know where to buy replacement parts for this pump. If you have a part number you might try EBay. Good luck!

How in the heck did you get the unloader valve loose from the pump? Its a brass nut and it seems like it just can’t be broke loose. Almost seems like I need to put an impact wrench on it!! Thanks

@LivetofishOutboardRepair

3 жыл бұрын

Did you remove the center screw first? That might be holding it I can’t remember.

The only part you'll need to get endless service, is a flux capacitor. Order one and you'll never regret it.

@LivetofishOutboardRepair

4 ай бұрын

😂 😂 😂

It chowed the key!

seems to me that if the key was shredded (and it def appeared shredded) something locked it up.

@robertapreston4200

2 жыл бұрын

did you find that something??

@LivetofishOutboardRepair

2 жыл бұрын

Roberta Preston… No I couldn’t find anything that caused the shaft to lock up. I’m thinking the key may have shifted out of position and the crankshaft just destroyed the key.

You caan get about any thing at Mcmasters and Catrr.

Add after only 90 sec?

@LivetofishOutboardRepair

2 жыл бұрын

Eagle Media…. I believe the key was shredding over a long period of time and it finally completely disintegrated the first 90 seconds of operation at the beginning of the spring season when I went to use it. So this was not just a quick failure.

@eaglemedia19

2 жыл бұрын

@@LivetofishOutboardRepair Your KZread video beginns with advertising (Add) and just after 90 seconds another advertising (Add) comes.

@LivetofishOutboardRepair

2 жыл бұрын

Eagle Media … Sorry about the Adds but this video is one of my most popular and I believe KZread runs these adds because it is popular. You should be able to skip certain adds. If not, I appreciate your patience and hope you still watch the video for its content and hopefully helps you solve a similar problem with your equipment.

Not a woodruff key hot rod. Standard key, ya know, common practice

@LivetofishOutboardRepair

2 жыл бұрын

Wade Smith …. Thanks for making that distinction. I work mostly on outboard motors and make that mistake a lot. Keep watching and making those type of observations. It makes my videos better with constructive remarks. Thanks again.

Where is Part 2?

@LivetofishOutboardRepair

4 жыл бұрын

It’s called “Pressure Washer Pump Maintenance & Repair - Oil Change & New O- Rings - Part 2” I have linked it into the description along with Part 3.

That is a standard square key, not a Woodruff key.

@LivetofishOutboardRepair

2 жыл бұрын

Mike Nakano … you are correct. Thanks for clarifying.

@maccurtinequipmentservice8915

2 жыл бұрын

Where do you get a square key for this application? I’m working on a pump now that’s almost identical.

@LivetofishOutboardRepair

2 жыл бұрын

@@maccurtinequipmentservice8915 just Google it. Amazon has them 3/16” for Honda engines. They are standard size.

@mikenakano9655

2 жыл бұрын

@@maccurtinequipmentservice8915 Any hardware store should have the appropriate material. Ace hardware is a safe bet, but I am not sure of the lengths available.

@gregmccarter2176

8 ай бұрын

Looks like someone left the key out...the key is made of steel..it would have trashed the pump had it done what you suggested...its a 1/4 key