Press in, out and replace wheel bearing and hub with simple tools.
Тәжірибелік нұсқаулар және стиль
I show you how to replace wheel bearing with simple tools.
23Pcs Front Wheel Drive Bearing Removal Adapter Puller Pulley Tool Kit
www.ebay.com/itm/23Pcs-Front-W...
Пікірлер: 226
1:39 no special tools required ...other than all the special tools you already got lol just kidding, thx for making the video, and definitely appreciate the extra helpful information. Also I like how your straight to the point and don't waste time, you do a great job with explaining it. What would I do without these helpful how-to videos? Also it would be helpful if you mentioned what year, make and model vehicle your working on, but no big deal
Freezing your bearing before install, then freezing hub before install helps a little. Freezing the parts shrink them slightly... Thanks for the vid!!
@ThatRandomSkater1999
4 жыл бұрын
freeze the bearing and not the hub. it'll make both parts shrink if you freeze both but it'll make only the bearing shrink if you freeze the bearing.
@electroKrunch
4 жыл бұрын
@@ThatRandomSkater1999 - Right, I was posting a bit late at night. Freezing bearing & heating hub eases installs. That's what we used to do on mining equipment back in the day with bronze bushings... Thx ;)
@SpeedySailor
4 жыл бұрын
@@electroKrunch , Since the Hub fits inside the Bearing, You do want to freeze both. Just need to let the INSTALLED Bearing warm up 1st. Of course, if you are working in sub freezing garage-outside, this technique is not so good. I would not recommend heating the Knuckle unless Mother nature does it for you.
Excellent video!!! Thanks for the video man...It helped me to remove my wheel bearing from 1997 Infiniti I30. I did it without disconnecting the ball joint and tie rod because of your video. Thanks again. You are the best!
It would have been nice to see the actual work but nice job highlighting the key points. Thanks!
you can also, use your old bearing race (that you press out) as a "tool" to press in the new one. :)
@SammytheStampede
4 жыл бұрын
Rasputin 883 great tip, thank you!
No blabbering. Just straight up information. Nice!
@AndreychukAndrey
5 жыл бұрын
Thank you
@becomematrix
5 жыл бұрын
Andrey Andreychuk a lot of youtube videos miss the point. This one is just right!
Pretty good video. I just ordered this tool kit on Amazon. I already have the hub removed but couldn't do anything with the bearing. So just checking on how the tool operates. Thanks!
Thank you for your effort in explaining the tools and procedures. You made some good points, and if viewers can't manage to gain some useful information here, along with other similar videos, and service manuals, then they should switch off their youtube account and pay a shop to do it. You gave, for free, your way of approaching this repair. Don't be discourage by snotty people;.
I think your video supplied some very useful information. I plan to purchase the kit on Amazon as I do not have a press. It and the kit makes more sense. I already own a slide hammer and can identify the lug nut interface for it that some are having a hard time comprehending. What I do think they were trying to say in a crass and rude way, was the video lacked fluidity. It would have been more well received if the what, how, and when were more detailed and laid out in a timeline. I watched other videos and personally replaced wheel bearings many times, so I know what you were trying to say but the video appeared to jump from point to point without any understanding or connectivity between the previous or next segment. Again, thanks for the information and keep at it, just plan out your next video in detail the next time. Best of luck!
Thanks bro. Hope everyone goes smoothly when I replace mine. I don’t have a shop press.
@NhiNguyen-zi3ro
4 жыл бұрын
David G kingdom hearts 3 trailer
thanks for the info on bearing magnetic side towards the engine
@hdbmw0101
6 жыл бұрын
Pro
That's GREAT. I had to eventually purchase that same ball joint / bearing kit to do my ball joints. However I purchased the wheel hub assembly and ended up putting the whole knuckle on the fire to 400 degrees and the wheel hub assembly in the freezer. The wheel assembly just dropped right in without any effort.
@5jjt
4 жыл бұрын
So, you mean, if you had sat there with a torch heating up the knuckle, then grabbed the frozen bearing, the bearing would have just slid right in?
Thanks so much for this video. I had my wheel all apart today and when I popped out the hub it looked like half the old bearing came out with it and it was fused to the hub shaft. You just verified this same occurrence. Next time I won't waste time, I'll buy a new hub with the new bearing. I rented the same wheel bearing press kit from Auto Zone. It's not even renting. They return 100% of your deposit upon return. Thanks again!
@scotts3563
4 жыл бұрын
Wow, I actually installed a new bearing today! That Sucker was in there! I had the impact wrench on full force for a solid 4 minutes! There was no way a ratchet was going to work. At first I thought I forgot to take off the retaining clip in the front because it wasn't moving at all. Put some heat on the knuckle and some WD40, waited a few minutes and finally she slowly popped out. I thought my impact wrench was going to burn up, thank God it was a Craftsman! The new one went in with a standard ratchet, much easier! I sanded and cleaned the sleeve with ultra fine wet sand paper and used a small screwdriver to clean out the retaining clip groove so the clip would sit deeper in the channel when reinstalled. Parts were from RockAuto.com.....Bearing: $16, Hub: $20. This video saved me and my family $530. God Bless you! - Scotty.
It's good to see that I can install the bearing with only hand tools. No need to buy a press or risk fracturing the bearing the with an impact tool.
If you remove the knuckle from the strut and leave it attached to the ball joint, the knuckle should be able to pivot outwards and give you more clearance to use the bearing/hub press tools. I just noticed that on another video and I was impressed. Also, the press tools are commonly available to rent from auto parts stores (for free).
@utopia2112
2 жыл бұрын
@@GrindSultan you seem nice.
Outstanding video man. Just bought the press kit.
I've done a lot of research and I think everybody has a tip to offer up such as on your vid I was not aware the magnetic side has to be placed towards the abs sensor it makes sense, and on seeing how the bearing was originally installed I would assume it's the case,now on another vid a guy placed the bearing in a freezer and baked his hub for an hour or so after he literally dropped the bearing in the hub and quenched the heat as it may damaged the bearing ,cool trick. I think I could easily complete this installation as I work in a Electrical Transformer repair shop and work on a variety of mechanical repairs.but getting some of these parts off is not like u tube lol .I also had a rotor that was really stubborn but I got it of (with a trick I learned on u tube) after an hour it finally gave away but then these press in bearings can get f*u?k in the process hence the wheel bearing vids lol
I just bought one of these kits, 23 piece, $65.99 on Amazon. Suzuki SX4 Sedan front bearings are a PITA. Rear is just 4 bolts (FWD Sedan) and unplug sensor. Slide Hammer I have, works awesome.
@AndreychukAndrey
5 жыл бұрын
Ya I did the rear on the mazda and yes bolt on. I wish front was like that.
@somethinburnin
5 жыл бұрын
Lol me too, damn air hammer bit me trying to do it another way.
For honda crv 2 000 ex 4 wheel drive 5 speed what numver i need to used for from hub and bearing tanks you
Nice video, i have to get the bearing tool.
Thank you for your great details video . Nice job
"No special tools required" Uses Special Tools ordered on Ebay LOL Great Video! Made my job easier, thank you!
I would have wanted to see how you removed the old one out
@mattmgarza
5 жыл бұрын
@iTheGeek no shop press needed?
@waywardwizardmedia
5 жыл бұрын
@@mattmgarza Reverse direction and use the receiver cup attachment where the old bearing slides into
You can rent all 3 in autozone now. I am on my way to do this job for my rears tomorrow. Got all 3 tools from autozone loan a tool free with deposit.
@jrfvismanos
4 жыл бұрын
Sorry about that. Just an update from a 2 year old post: It was a struggle for me as first time doing this such extensive job - took me about 8 hours. But the good news is my project was a success. I did it for my 09 BMW 328i and to this day it is still working perfectly. Goodluck guys!
You don't need a slide hammer. You just use the Bearing removal/ install tool you bought. If your Circlip is in the front, you should remove the bearing from the outside and install from the inside after installing the new circlip to act as a stopper. My BGS clone used long bolts to press out the Hub.
@damiengilles350
5 жыл бұрын
Hello Charlie Wolf, I've just ordered the same bearing removal tool (www.ebay.com/itm/23pcs-Front-Wheel-Bearing-Press-Kit-Removal-Adapter-Puller-Pulley-Tool-Case-/264317979763?oid=182244109161) but I have not received it yet. However, I'm trying to figure out how can I use that tool to remove the hub ? If I can save a bit on the rental of a sledge hammer it's all fine with me. Could you please point me in the right direction ... a video or tutorial somewhere, the tool manual maybe ? Thanks a lot for any help you may be able to provide !
@zlix_2045
5 жыл бұрын
@@damiengilles350 Did you need the slide hammer?
Andreu, great video, got a lot of good points. Question to all, instead of buying or renting tools, why not take the hub and the new bearing to a machine shop and let them press the old out and the new in for you. Probably cost about the same as the tools that you probably never use again. Good job.
@bbqkip
5 жыл бұрын
Henry Quintana because you’ll also have to get the spindle off and you can use the tools on your other 3 wheel bearings.
Andre andreychuck! You the man!
It looks like when you pressed in the hub you didn't support the inner bearing race. I couldn't tell since you didn't show the setup of the press, but if you don't line up the other end of the press with the inner race you will trash the new bearing.
Thanks mate. Very helpful & clearly explained.
Great videos. Subbed ! 👍🏻
Thanks for your time. Video helped me. So tired of negative comments from the loser gallery, going through life and make other peoples life harder instead of easier. Go back down to mom's basement
@MrStinky2011
5 жыл бұрын
Absolutely!
Top tip when pushing in the hub use the smaller plate to go at the back of bearing or else you will push the centre of the bearing through this way and Fuck the bearing learned the hard way myself
Wish I see “ how to remove” than how install part. ( we’ll both ways) thanks for sharing...
@DonnieDarko1
3 жыл бұрын
🙃
First and most important thing that can't be stressed enough is to FREEZE THE BEARING and you can also get the steering knuckle hot and then when you put them together it will just slide right in.
What size socket does the kit need?
Straight to the point, thanks! Do you need to remove the abs sensor?
@AndreychukAndrey
3 жыл бұрын
I don't remember.
a picture's worth a thousand words man
Good job bro!
@creativeflashes703
6 жыл бұрын
Darwin W り
you actually set it up backwards, you want the long nut on the front/outside and the bolt coming from the inside towards you towards the outside
I heard that you froze the hub bearing for an easer install. Would that introduce water in the bearing when the bearing thawed? Was thinking of doing the same thing on a double sided idler pulley bearing but also heating the pulley first and then installing the frozen bearing. What do u think is that an over kill.
@AndreychukAndrey
4 жыл бұрын
Honestly I'm not sure if frozing it made it go in easier or not. I still have the car and still no issues.
So before this video, I saw one that showed how to do this without the tools. A lot of hammering with a heavy hammer. NOT GOOD! I like that FWD Front Wheel Drive Bearing Adapters Press Kit Puller Set, but I need to find one with great reviews. Right now, a lot of them, that look exactly like the set in this video, people are complaining that the big bolt and matching long nut strip their threads. THAT'S BAD! I also like that in this video, it's done right on the car, rather than having to remove everything and again, banging on ball joints and the like. The only thing, I wish, is that it could have been clearly demonstrated how to remove the bearing using this special set. As expected, the instructions in these sets are trash. LOL But that's fine. There's a lot of people who know how to do this. So, more video watching to come.
Hi.Do you think that it would be possible to replace the suspension arm bushings with this set. I need to replace 70 mm trailing arm bush.
@AndreychukAndrey
5 жыл бұрын
Not sure.
I believe you can use the same red bag tools to pull the old and press the new, no need for the other.
I just bought the same kit online from Walmart, $61. You can return the kit to any Walmart for a refund if needed. The same kit, Maddox, at Harbor Feight is $99 with the 20% discount - lots of bad reviews about the weak bolt threads.
@douglasmanor4427
3 жыл бұрын
Do you know what size the bolt and thread count is?
Nice vid! Anyone know if I can use this kit (I've the same one ready to sort my bearings out) to change ball joints in the control arm?
@AndreychukAndrey
4 жыл бұрын
I think you can if not you can rent one at any auto part store.
@ultraglossdetailing786
4 жыл бұрын
@@AndreychukAndrey thanks, I guess I'll give it a shot and find out 😀
The salt that's used in Canadian roads seizes the clips
Thanks for this.
I needed some info. Thanks
good job !
where do you push it out? didnt see that.
If the pressing tool can be used to push in the new hub, hypothetically can it be used to first push the old one out? I mean instead of using that sliding hammer you rented.
@AndreychukAndrey
6 жыл бұрын
Mikhail Орен. I think so. The reason I used the slide hammer because my rotor was so rusted on the hub that I couldn't get it of the hub.
make sure grease everything
Hi I know this is an automotive tool but I have a bearing race stuck in a washing machine I was wondering if you think maybe I can use this tool to press out the race
@AndreychukAndrey
4 жыл бұрын
Not sure.
Spacibo ! Klassno !!!!!!!!!!
I see that that is a Mazda. What kind of Mazda? Were you working on the front or rear of the vehicle? I'll have a 2006 Mazda Tribute w/ABS, but my replacement bearings don't show a magnetic side. (?) Please respond. Thx
@AndreychukAndrey
5 жыл бұрын
This was for a mazda 3.
Hello, Can this tool be used to remove the hub ? I've seen comment that seem to say so, but I'm having a hard time figuring out how it could be used in such a way.
@AndreychukAndrey
5 жыл бұрын
I'm not sure.
@damiengilles350
5 жыл бұрын
@@AndreychukAndrey It seems like there is a kit that does contain M14 bolts that you can screw in the hub so it pushes it out. Unfortunately, my kit, such as yours, does not contain the bolts.
@damiengilles350
5 жыл бұрын
I've tried to source long M14x1,5 bolts but could not find some that were long enough
good info, many thanks
Thank you!!!
Assuming you can also press out the bearing using this tool without removing knuckle and strut assembly, correct ?
@AndreychukAndrey
4 жыл бұрын
Yes I think so.
I bought this set from Amazon about $86 and did not work for me. I still had to use a press to remove the bearing from the knuckle assembly and I can't return it because it's all smudged up.
Your giving good information thank you ☺
only thing i'd add is to make sure to lube the threads of the tool.
@AndreychukAndrey
6 жыл бұрын
Cooldude 22. Yes, I lube the threads with used motor oil
Great video, hell with the negative people. unfortunately on my 2000 saturn the c-clip is in the back so have to take off the whole thing and use a hydraulic press instead of hand tools. But now I know it is easier on other cars.
@Dewey-wz4ny
6 жыл бұрын
I bet they could be drive them out with an air chisel or a slide hammer. I plan to do mine that way in about a week. I don't have a press.
@4x4play4
6 жыл бұрын
there's another video with a guy pounding them out like that. all the comments tend towards, do you want to do it twice after you damage your new bearings?
Thanks brother
Nice video. But at 4:15 you showed the big adapter on the back of the spindle. It's much better and safer to use a smaller adapter that only covers the INNER Bearing Race as to not push it through and blow your bearing apart.
@707SonomaComa
4 жыл бұрын
Oh, and uh...... don't ask me how I know that! 😆
@ryan94mustang
4 жыл бұрын
@757WN yes I've blown out 2 bearings now this way.
@andrewroberts9134
4 жыл бұрын
@@ryan94mustang 🤣
You think your way we'll work for a 2013 Honda lxs 2011 and up
@AndreychukAndrey
5 жыл бұрын
As long as it's a press in wheel bearing, I don't see why not.
Thanks! I get it... & I wish my Russian was as good as your English! ^..^
@boateron
6 жыл бұрын
right on bro
Do you know the size and thread count of the bolt used to press?
@AndreychukAndrey
3 жыл бұрын
No sorry.
You can take it out too with that tool correct?
@AndreychukAndrey
6 жыл бұрын
shellumus. I think you can. Sorry i only needed to use it ones. That was my only time using it.
Can’t you use the wheel bearing tool for pulling out the hub?
@AndreychukAndrey
5 жыл бұрын
Not sure.
Would this set work for pressing in an out bushings?
@AndreychukAndrey
5 жыл бұрын
I never tried it.
@jesusmiranda2236
5 жыл бұрын
@@AndreychukAndrey honda lower control arm bushing is the size of the bearing, so was wondering if i could use it also for that purpose but ty anyways
didnt start out good, but later your explanations were very nice
@AndreychukAndrey
6 жыл бұрын
Gerald Braxton. Thank you.
What did you use the slide hammer for?
@AndreychukAndrey
3 жыл бұрын
I used it to get the hub out. I couldn't remove the rotor cause it was rusted on the hub. So I attached a slide hammer to pop it out.
Been told this can't be used on a rear brake drum with this tool I can't see why not
Just ordered the kit , do you remember what size deep socket you used in ur ratchet for the back side ?
@AndreychukAndrey
2 жыл бұрын
No sorry.
@Raygetplenty
2 жыл бұрын
@@AndreychukAndrey it’s gotta be like a 26 or 30
@AndreychukAndrey
2 жыл бұрын
@@Raygetplenty Can you send me a video time where I used it.
@Raygetplenty
2 жыл бұрын
@@AndreychukAndrey 3:05 it’s a deep socket you used to connect to the long adapter in the kit
@AndreychukAndrey
2 жыл бұрын
@@Raygetplenty It's a 32mm
wasn't bad just next time i would have like to have seen you using the tool
@AndreychukAndrey
4 жыл бұрын
Ya sorry it was my first time and just wanted to get it done.
If you freeze it doesn't that expand the bearing?
@klatuveradanikto
5 жыл бұрын
No. Metal expands when heated. Water expands when frozen.
@waynesanchez6504
5 жыл бұрын
No, freezing any metal makes it CONTRACT. I worked in an automotive machine shop and we regularly froze engine cylinder sleeves, prior to inserting them, into a block that had been bored out. When the metal reaches room temperature, you've got a nice, tight fit.
I’m on the west coast and I think autozone rents the kit out for $104 deposit
@shakeme3290
3 жыл бұрын
East coast Autozone rental is $370, refund when return. AND.. none of the stores around me had one in stock. Bought the same set for $51 shipped on eBay
Donde compro esa herramienta?
@AndreychukAndrey
5 жыл бұрын
Ebay
i wanted to see how you remove the old hub and rotor,and its not simple tools. its a special tools for bearing remover or what so ever.
@d.j.9961
6 жыл бұрын
simply use a slide hammer & adaptor that grips the lugs to remove hub. Then, use either a press to remove/install bearing & new hub or, use a 23 piece front wheel drive bearing removal adaptor puller pulley tool kit. can get 1 on e-bay from $48=52.91 & up. I paid 52.91 since it came with a lifetime warranty.
Thanks mate!
"No special tools" those are special tools.
@khanu5947
5 жыл бұрын
🤣😂
You "froze" them? Meaning you put in freezer?
@AndreychukAndrey
6 жыл бұрын
Caleb Sandersier. Yes, I read it makes them slide easily.
@wagonkit
6 жыл бұрын
Andrey Andreychuk interesting
@shaquillewhite-yardon675
6 жыл бұрын
It chills the steel which will slightly make it contract. Opposite of heating which obviously would make it expand.
The press tool worked better for me with the nut end on the outside.
@AndreychukAndrey
6 жыл бұрын
John Owens. That's a good tip too.
@JuanRivera-ff6fd
4 жыл бұрын
Yes, larger nut will take more of the torque, because it grabs more of the threads. Avoid using air torque, greater possibility of stripping the bolt threads. Ratchet will do the job, slower but less chance of ruining the tool. Especially when when using cheaper tool kit. You can also add a bearing on bolt side sandwiched between the two washers. This prevents the washers and adapters from getting chewed up. Also always grease or heavily oil the forcing bolt threads before every use.
that link you put for the bearing puller is no good. can you tell me the name of your kit ? Harbor freight has one buts its $120, Not trying to spend that much. Thanks !
@AndreychukAndrey
3 жыл бұрын
There's this one it has good reviews ebay # 201875497895
@YOPHILLYYO
3 жыл бұрын
@@AndreychukAndrey thanks ! I apprecaite it !
Getting the clip off usually takes longer than the actual bearing swap
@AndreychukAndrey
5 жыл бұрын
With proper tools its way easier.
Good
Astro bearing press tool kit
Shouldn’t you be able to do the whole job with that kit in the red box?
@AndreychukAndrey
5 жыл бұрын
By whole job you mean remove and install wheel bearing?
Andre do you run a shop?
@AndreychukAndrey
6 жыл бұрын
Albert Rodriguez. No
@hotrodriguez549
6 жыл бұрын
Andrey Andreychuk keep up the hard work buddy!
Where can I buy it
@AndreychukAndrey
6 жыл бұрын
Robert Glen. Ebay
@Dewey-wz4ny
6 жыл бұрын
Amazon has them everywhere, best ones around $66 with free ship - 23 piece and good reviews.
the only good info is the magnetic towards the the engine if you have abs sensor lol
This tells what he did not how he did it.- usless
wish you showed how you actually removed it
christ dude. looking at the condition of that race stuck on the hub, your wheel was about to fall off
@AndreychukAndrey
6 жыл бұрын
Marvin. Also the bearing was so bad that it was hard to hear the music. Also I decided to try remove rotor from the hub, when it was off the car, the part where the brakes hit the rotor broke off and the drum was still stuck on the hub.
@duaneafields
6 жыл бұрын
CrookedHillary. Love that name.. CrookedH
@charlescaston2404
5 жыл бұрын
What about the nut on the CV axle that wouldn't hold it ?
@vaquero3578
5 жыл бұрын
marvin - do not take the Lord's name as a curse word please.
1st, I have never seen a rotor so chewed up b4. iv seen rotors that have grooves around the rotor but, his looks like someone took a chisel & hammer to it. One generally doesn't need 2 replace their rotor when doing a wheel bearing! tip 1, use HI-TEMP BEARING GREASE 500-550+ DEGREE .... & TIP 2, WHICH SHOULD BE TIP #1, CLEAN UP WITH BRAKE CLEAN & MAKE SURE YOU CLEAN YOUR ROTORS VERY WELL & FINISH UP WITH YET AGAIN A FEW MORE SPRAYS OF BRAKE CLEAN!!! NOW, BACK TO THE VIDEO...
@AndreychukAndrey
6 жыл бұрын
D.j. B. At 1:00 you can see inside of the rotor how bad it's rusted. Also I was replacing rotors any way so it worked out perfect.
मुझे यह टूल किट चाहिए
Build the wall
Snap ring pliers + snap ring
Didn't really SHOW anything being done :(
@AndreychukAndrey
6 жыл бұрын
Steve B. Sorry but the whole point of the video was to show that's it's possible to remove and mount your wheel bearing and hub without special tools.