Great video. I dont have the patience to make videos like this. One life hack. Heated the bearings slightly with a torch and they hand fit onto shafts, also heated the alum case around bearing seating areas and case went on by hand also. It dont take much heat!

@crankitt825

4 күн бұрын

Thanks for the tip and for watching my videos.

Thanks for posting this. I used it to repair my '08 700 X2 Transmission. Was pretty similar to this one. Turned out my chain and tensioner was the issue.

@crankitt825

7 ай бұрын

Your very welcome and thanks for watching!!!

Excellent very professional thanks a bunch from Ireland best wishes ,TC

@crankitt825

4 ай бұрын

Your welcome!! Be sure to like and subscribe to our channel.

You’re very welcome!! Be sure to like and subscribe to our channel!!

You made it look easy! I am going to attempt this here soon. Hopefully it goes as smooth as this! Thank you.

@crankitt825

10 ай бұрын

You can do it, just take your time and go by our video. Thanks for watching and don’t forget to like and subscribe to our channel!!

@taliento73

9 ай бұрын

Update.. everything went good got every thing back together. Again thank you for the helpful videos and I did subscribe and like 👍

@crankitt825

9 ай бұрын

You can do it!! Just take your time and follow the video. Thanks for watching and don’t forget to like and subscribe!!

Top notch video! Saved me for sure

@crankitt825

6 ай бұрын

Glad you liked it!

Very good video!

@crankitt825

Ай бұрын

Thanks, glad we could help. Be sure to like and subscribe to our channel.

We replaced these items on a few Ranger transmissions now - However one will not hold the wheels/axles still in park after we went back together. No issue with the other 3-4 trans rebuilds. Any pointers that we could try? Thanks for a great video!

@crankitt825

3 ай бұрын

Thanks for watching. Sounds like something is wrong with the turf mode. Turn your turf mode off and put it in park and see if both wheels lock. Don’t forget to like and subscribe to our channel.

Been watching your video . Good to watch . I've got a Polaris Ranger 570 the back diff has a crack .will that effect the gear box new to this thanks

@crankitt825

11 ай бұрын

Hi and thanks for watching. Yes a crack in the back diff will let the oil leak out and cause further damage. Take the diff to welding shop. Depending on location if they can’t weld the crack up, then you will need a new case.

Glad you like it. Be sure to like and subscribe to our channel!!

Just curious about what this would cost and how many hours for the total job. Very good video! Thanks.

@crankitt825

8 ай бұрын

About 8 hrs. parts and labor will be around 1600.00 if you paid some one.

May have an opportunity to buy a 2015 ranger 6x6 diesel with reverse shifting problems any advice and what to look out for hope to look at it tomorrow thanks in advance Tom Clayton, watching you from Ireland, the guy is looking for 3500 euro , about 5000 dollars

@crankitt825

4 ай бұрын

Hard to say without seeing it in person however here a 2015 would retail for about 8.000 dollars. With them wanting 5 thousand and a bad transmission doesn’t sound to good. Next I would check the hours on it. If it has over 4 thousand hours depending on how it was used it could be time for a rebuild. Also the gas Ranger is also faster then the diesel and easier to start in the winter then the diesel. Hope this helps and thanks for watching our videos.

@tommieclayton743

4 ай бұрын

@@crankitt825 many thanks there's 7600 miles on clock mab y that's not too bad going to look at it shortly certainly if I buy it I know I will have your videos to assist me , thanks most sincerely again, peace and love from Ireland,TC

@crankitt825

4 ай бұрын

You’re very welcome!! Be sure to check back. We put new videos up all the time.

curios, it looks like the "ears" on your other gears are wore too... did you address that?

@dustinwittig1290

7 ай бұрын

also thanks for the video.

@crankitt825

7 ай бұрын

Yes all check out good. Polaris is doing great now!! Thanks for watching!!

FYI put the bearings in oven at 350 or 400 for 30 minutes and they all but slide on.

@crankitt825

9 ай бұрын

Thanks for the information. I have a press but that information will be good for the other followers. Be sure to like and subscribe!!

What did this cost with labor

@crankitt825

8 ай бұрын

To hire this job out you’re looking between 14-1600.00 thanks for watching and don’t forget to like and subscribe to our channel.

Nice work ! Excellent video !

@crankitt825

11 ай бұрын

Thanks so much!! Don’t forget to like and subscribe to our channel!!

@happydayz5321

11 ай бұрын

@@crankitt825 Done . Again Thanks !