This is fantastic. I’ve got the same bike and faced MANY of the same issues. Thanks for the video!

@bmcoutside8446

5 жыл бұрын

seth364 Thank you. I’ve been a bit lazy with part 2 but I’ll upload it really soon!

@seth364

5 жыл бұрын

BMC Outside Hehe, no worries! Mine has been a project ever since I bought it. One quick note, if you notice oil leaks, watch the hoses at the radiator. The OEM setup was prone to deteriorate and leak. I replaced mine with the braided steel hoses and haven’t had problems, EXCEPT for the removal of the dang things. The oil cooler radiator is particularly weak at the joint and if the threads to the hose are on tight, you might just do what I did and accidentally rip the radiator top in half trying to get the dang hoses off. Anyways, been a pretty decent little bike. Hope you’re enjoying yours.

Nice one matey ( subbed for you 👍)

@bmcoutside8446

4 жыл бұрын

Northwales Bushcrafters Thank you 👍

What causes the drive belt to flip over or come off even? Any way to tighten it

Where could I get all parts to rebuild? I need wiring harness and all.

Is there a part 2 ?

Is part 2 coming? ;) I’m in need of replacing the spark wire but can’t figure out where the ignition coil end is mounted. I’m hoping to not have to remove all the front panels. Any thoughts?

@bmcoutside8446

4 жыл бұрын

Parke Gregg Yes part two will be along very soon.......at last! I’m not sure off the top of my head but I’ll have a look for you and let you know my findings!

@TeslascopeMobile

4 жыл бұрын

@@bmcoutside8446 I've since found it under that access plate in the front under the handle bars. Would still like to see a part 2... :)

@Tommysunny93

3 жыл бұрын

Any update on part 2?

@jackdipper7686

2 жыл бұрын

Part 2 dude

Good video but certainly wouldn’t of hurt to spray some WD-40 before twisting bolts and screws

I know its 11 months later but hey I'd watch a part 2

@bmcoutside8446

4 жыл бұрын

Part two and three footage is all recorded, I just have to find the time to edit it! Part two will be ready really soon!

@jorcktheoutcast8007

4 жыл бұрын

@@bmcoutside8446 sounds good to me, I have notifications on for it whenever it comes 👍

@nicholasbrophey1145

4 жыл бұрын

@@bmcoutside8446 carb rebuild is what i am hoping for, just bought 2004 330 magnum 4X4.

Mine doesn’t want to go into park or high do you know how to fix that

@bmcoutside8446

5 жыл бұрын

Hunter Poucher There should be a spring attached to the rear brake pedal, that pulls on a shaft when you press the brake down, which allows you to engage park and high. The spring could be over stretched, if so try pulling the shaft down by hand and engaging park. If it works you just need a new spring.

@hunterpoucher3938

5 жыл бұрын

BMC Outside thank you

Hey man I have the same quad and need some help figuring out what’s wrong with it any chance you could help?

I have so many questions

@bmcoutside8446

Жыл бұрын

Fire away! I’ll do my best to answer but it was a few years ago now!!

21:50

@benduker6839

3 жыл бұрын

??

This video would be so much more helpful if you actually said what you were doing and what tools you’re using. Just my opinion

@bmcoutside8446

4 жыл бұрын

Casey Olson I’m planning to add some voice over for part two, not the whole video, just for the parts that aren’t obvious what I’m doing!