awsome video did a good job rebuilding the motor thumbs up and shared

Thanks!! I thought my kit was missing the head gasket. Turns out its just got the outer gland and cylinder Orings. I was thinking it was an actual gasket like the bottom

My outter cover seal went on mine..well its leaking from there on both sides in the front by the exhaust manifold, think I need to replace the head gasket also?

Hey AKproXR did you have to set your timing different when you rebuilt that topside?

What year is this engine? Have a 2011 that I want to rebuild.

Any suggestions to upgrade my stock clutch on 06 polaris fusion 600 ho?

Why did you remove the durability kit?

How long did that take you to do?

your old sled is super cool AKproXR

@AKproXR

6 жыл бұрын

Which one? If your talking about the black/orange switchback assault I still have it!

@annaekamrak8354

6 жыл бұрын

AKproXR black and orange

@annaekamrak8354

6 жыл бұрын

AKproXR nice intro

@matthewweninger5435

6 жыл бұрын

How come you guys didn't put the fix kit back on? What pistons did you use?

Are those spi pistons forged or cast? I just got my spi pistons in and compared to my wiseco forged pistons they are way heavier. Just curious.

@ryanbenbow-zx2sd

10 ай бұрын

I don't know. But spi is a Good brand of piston. I have them on my zrt 6oo. I would use weisco Pistons on my zrt 800😅

Dude You're adverts included cats and tires. In already in!

I need to know the break in procedure for a rebuilt 800 Polaris you know?

@sheldonmoseley

6 жыл бұрын

When I bought a new sled it was a 200 mile period of varying throttle and not holding at same speed for long periods of time. I just recently rebuilt a top end and I suggest not really hammering it for the first 3 hours of operation after rebuild. There are plenty of small variations people use. These are the ones that I have personally done.

@cdnbcn6164

4 жыл бұрын

2 full heat cycles, a nice gingerly ride for an hour and brappppppppppppppppp...

Would anybody know if I have to pull the motor out of the chassis to replace a top end? Thanks

@cheeseymccheese7249

Жыл бұрын

Its a year late but i doubt it

How are those pistons holding up I bought same ones?

@AKproXR

5 жыл бұрын

Zero issues. Most 800’s in my group have them.

On 2015, does Digital Wrench have to be used to finish job? For oil?

@AKproXR

Жыл бұрын

Digital wrench was the equivalent of a ODB scanner for a car. Just relays information on sensors and shows stored codes. I Havnt used/had access to digital wrench since 2012 though.

@MarkDulisse

Жыл бұрын

@@AKproXR I have to remove steering post to pull my cylinder. Post goes to front floor on chassis but it’s so tight I can’t get at bottom nut to disembark. It’s a 2015 pro S 800. Any ideas?

Do u have a video of pulling the motor out by chance?

@jwgowitz5325

4 жыл бұрын

Can't seem to find any info/videos on pulling the motor. Purchased a 14 800 needs some crank bearings original owner ran out of balance clutch. Any help would be appreciated

@2strokeadventures

4 жыл бұрын

@@jwgowitz5325 I just pulled my motor and took the crank out.... Didnt watch nothing or use a manual... Just go for it and do the best u can :) re assembly is were everything has to be 100%

@2strokeadventures

4 жыл бұрын

@@jwgowitz5325 it was really easy, removing the primary clutch was the hardest part

#AKproXR add music your my favorite fan

@AKproXR

6 жыл бұрын

Thanks bud, I'll look into adding some music in future vids! Thanks for watching

How often you have to rebuild?

@nathantrey9484

4 жыл бұрын

Once compression is at 100-105.

No sealant for the base gasket?

@AKproXR

5 жыл бұрын

No

@AKproXR

5 жыл бұрын

If you feel the need, you can use spray on copper coating or what ever your preference is. But these don’t really need it.

Why did you eliminate The Fix Kit ?

@AKproXR

6 жыл бұрын

Because its pointless. only one sled in my group has it and all the sleds without has proven to be just as reliable. Granted we do top end rebuilds as routine maintenance (as should be done) we choose to do them at around 2,000 miles.

@yanl5448

6 жыл бұрын

AKproXR would you sell your reliability kit? Spacer and dowel pins

@cameronbarron

3 жыл бұрын

@@AKproXRhow many miles did you get with the rebuild? Still have the sled? I'm buying a 2010 dragon this week. And am researching the heck out of them. Kinda nervous about them now lolol I would've kept it , one less thing to worrie about. It's the shitty oil supply that is the killer on these sleds I read . Alot of them are taken out because of the bad oil cap design

@cameronbarron

3 жыл бұрын

@@kjohns68 ended up backing out on the sled. Reading so many horror stories on them ..needed dragon savers and oil caps and oil turned up and all this shit lol and I got the dealer to do a compression test on the assualt it was 70 and 110 just redy to explode . I couldn't believe they didn't rebuild it or test it before that(it was at a Polaris dealership).so just gonna rock the prox2 for another year ...

@zachschmaus3188

3 жыл бұрын

@@AKproXR does your friend notice much more torque out of the fix kit from the additional stroke length?

You do not explain anything . you have the video just running fast

@AKproXR

6 жыл бұрын

RICHARD maaske the general description of what needs done was added in text... along with torque specs etc... if you want detailed instructions as to how to rebuild an engine you will have to get a book as I’m not uploading a several hour long video..