Hey guys, this is an upgrade to my first cabinet and now has more storage for a brand new jig. Even if you don’t have this jig you can easily alter the height measurements to fit yours. All my plans are in a pdf format and are easy to follow. Thank You!!!

@MerchantNation

4 жыл бұрын

Have you had any alignment issues with pocket hole bores? I just bought one of these after watching another youtubers video. The first one I received had a fairly prominent canter to the pocket hole sleeve (ie one sides edge was sticking out about 2mm) The manufacturer immediately shipped a replacement, but the 2nd to arrive also had this same defect about 0.5mm. Both of these units do not get side by side pocket holes bores to line up. My assumption is that mould used in production either has a defect or has worn out and not embedding the metal components properly into the plastic/resin mould. I went to the local HD and popped open a kreg and their unit is flush and level between plastic casing and metal bore sleeve components. Just wondering if I'm unlucky or if others are experiencing the same

@rhwoodshop

4 жыл бұрын

I just checked my sleeves and they are spot on within .003 inches. Maybe it’s possible they have fixed the mold issue and they are newer production models are fixed.

@MerchantNation

4 жыл бұрын

@@rhwoodshop Cool. I may have to do some more test, but just to confirm we are talking about the same area... Im referring to the front face where the drill bit exits from the metal and starts making contact with the wood. Not the removable sleeve for adjust dual hole spacing.thx again for updating.

@rhwoodshop

4 жыл бұрын

tellMeSomething iDontKnow yes, exactly. I measured from the top where the drillbit goes in to the top of the sleeve where the bit exits at the bottom.

@MerchantNation

4 жыл бұрын

@@rhwoodshopnot quite the same as what I was describing. However, i assume if you measured that u would have noticed if the top ridge was protruding. Hard to described, but mine was if you look at the top horizontal edge, from left to right, one side is protruding farther far the plastic housing than the other. So, technically, the metal housing was fully seated and sits at a pitch from left to right. So diff from what you described, but i would think that it would be noticeable if you had a similar issue. I must just be double unlucky to get two for two. Thx again

sure is an elaborate pocket hole cabinet 🤣🤣🤣🤣🤣👍 I keep em n one place, a DRAWER 🤣🤣🤣🤣🤣💪🏻

Yeah! Shop projects again, I missed them. Happy for you that you have sponsors again.

@rhwoodshop

4 жыл бұрын

Patrick Yanez Thank you so much Patrick, yes I will be posting more shop projects because I do have some more plans for my shop!!! The tool partners really help!

Great video!! I am getting back into woodworking after about a 30+ year hiatus and I am pleased to come across your channel. Looking forward to seeing what else you have out there! Thanks, Jessie

Nice shop project. Thank you for sharing your knowledge.

@rhwoodshop

4 жыл бұрын

jeremy Shields so glad you liked it Jeremy and thanks for commenting.

Definitely a nice pocket hole cabinet. Snazzy! Love your table saw setup.

Great project Drew! Really like the options you added to the cabinet, all in one place, I like it!!

@rhwoodshop

4 жыл бұрын

Thank you Jb! I have been really putting this design together for a while now and finally got to make it. Been excited for this video release.

Great idea for what looks like a great tool!

@rhwoodshop

4 жыл бұрын

It was a really good upgrade considering what I used to have. Thank You!!!

I love it. Looks amazing and practical too

@rhwoodshop

4 жыл бұрын

Very practical and easy to take with you on a job site if you wanted to. Thank You!!! So glad you liked it.

Awesome work Drew, it turned out great! 😍👌🏻👍🏻👊🏻

@rhwoodshop

4 жыл бұрын

Thank you so much Fred! I appreciate it a bunch!

I'm a newbie. My Amor jig is supposed 2 arrive tomorrow. Can't wait. Beautiful cabinet. Hope I'll b able 2 do something that awesome someday.

This thing is epic! Boom!

@rhwoodshop

4 жыл бұрын

Thank You!!! This means a lot.

I love your thought process Drew. I have been following your SketchUp series and was thinking that you probably went through all of the planning there first. Great project, I love your color match skills. Thanks for sharing!

@rhwoodshop

4 жыл бұрын

Felix from Nebraska yeah about 90% of my planning went into the sketch up model but there were a couple of things that I changed in the process because I realize that it wasn’t going to work the way I had envisioned. The pocket holes were one of them. I actually had pocket holes going up and down on the sides but I did not realize that I wasn’t going to be able to have access to them after the middle divider was put into place along with the tops. So I had to remove the pocket screws there and the notch out on the middle divider was another change.

I haven't watched the video yet. I just wanted to tell you how excited I am to see you posting videos again. Boom!

@rhwoodshop

4 жыл бұрын

Doug McHone Hey Doug, thanks a lot for dropping me a comment. It’s good to be back and I am enjoying it very much.

Really nice build Drew! Looks great.

@rhwoodshop

4 жыл бұрын

Thank You!!! I’m so glad you liked it.

That is cool awesome great job and I want love like cabinet 2.0 so I hope wish learn more like you is cool “ AWESOME “ .❤ thumbs up

Man, that's super nice.

@rhwoodshop

4 жыл бұрын

Thank you. It’s been a nice addition.

Very flash setup mate, I love it as it has metric measurements, the scale I understand lol 🍻👍

Very nice, you sir are a true professional.....

@rhwoodshop

4 жыл бұрын

Thank You!!! That is an awesome comment. I really appreciate you saying that!

Excellent job Drew. But I wouldn't expect anything less from you.

@rhwoodshop

4 жыл бұрын

Steve Gronsky hey Steve, long time no see, hope you’re doing well. Thank You!!!

I have followed you for quite some time. I absolutely love your SketchUp videos and have commented on them already because they are the best tutorials I have found so far. I was intrigued by this project because it was both practical and has an awesome look. That led me to do more research on the Armor Tool Auto-Jig. I wanted to say thanks for the great idea on the pocket hole cabinet, but moreover , for showing the Auto-Jig. I bought one a few weeks ago and was finally able to do my very first pocket hole project. So far it has turned out great and I love the Auto-Jig. It made things so much easier and I am way more confident now as I start to prepare for building cabinets and workstations in my garage. Please keep the videos coming. Of all the channels I subscribe to, yours is the only one set to receive notifications...#armortool #pocketholes #rocknhwoodshop

@rhwoodshop

4 жыл бұрын

Bill you just made my day with this comment. It’s words like these that keep me going and making sure that I produce the best available content that I can. I am so glad that you are getting use out of these videos. I actually just completed one and in the process of uploading it to KZread. You should see it tomorrow at 9 AM central time. Thank You!!!

Impressive to say the least.

Very nice looking work station Drew.

@rhwoodshop

4 жыл бұрын

Thanks so much. It will get some use for sure.

Wow, The 2.0 version is a so-so good. A + Rating Two Thumbs Way Up. Gotta make a purchase of that Armor pocket hole jig super cool features I think is better than Kreg.

Very Nice!!!

@rhwoodshop

4 жыл бұрын

Thank You!!!

Great Video! Love what you're doing and keep up the great work.

@rhwoodshop

4 жыл бұрын

Thank you so much. I am happy you approve.

@rhwoodshop

4 жыл бұрын

Thank you so much. I am happy you approve.

Pretty cool 💪🏼

@rhwoodshop

4 жыл бұрын

Thank You!!! Glad you liked it. I enjoy using it.

@Aepek

4 жыл бұрын

Rock-n H Woodshop thanks for building it. Only question I’ve got, (& even the one thing I don’t like about this tool); does the pocket hole jig come out to be able to use as standalone jig, like on the Kreg K5 (even old K4)? Cuz that would be cool, but mine doesn’t & wondering if “just doesn’t” or I’m doing something wrong, lol

Awesome build! Should get a lot of use out of that.

@rhwoodshop

4 жыл бұрын

I know the cats like to walk on it. 🤣

Bellissimo lavoro,💯💯👍👏👏👏👏👏👏❤️.shared

@rhwoodshop

4 жыл бұрын

You rock thank you so much.

Drew, great video again. For those who are on a tight budget and have the Kreg K4 Armor sales a bracket and an adjustable clamp to convert the K4 with their adjustable clamp. Also, most of the plywood sold at big box stores is 23/32 and 15/32 but I usually use a micrometer to see its actual thickness. As always I really enjoy the videos you produce.

@rhwoodshop

4 жыл бұрын

Good point there Michael and thank you very much for sharing such good information with my viewers. I’m sure they would really like to know what they’re in for when they go buy plywood it big box stores. You rock man!

@michaelmcdonough1989

4 жыл бұрын

@ichiban2point0 What failed. I have used mine many times and it works okay. Thanks

great video

@rhwoodshop

4 жыл бұрын

Thank you so much. I really appreciate the comment!

On the part using the jig as a stop block, I’m thinking you could have just flipped the door front around on the second cut and it would have cut exactly the same on the other side centering the opening to finish hogging out the middle.. Great video as always Drew.

@rhwoodshop

4 жыл бұрын

You are right! you must be exactly centered on the stock though. However, this takes out that guess work. You are really good dude, great catch.

Nice work my friend!

@rhwoodshop

4 жыл бұрын

Thank You so much. I appreciate it.

@Norrisnettv

4 жыл бұрын

@@rhwoodshop Keep up the great work..

@rhwoodshop

4 жыл бұрын

Norrisnettv I will do my best!

@Norrisnettv

4 жыл бұрын

@@rhwoodshop #armortools makes a great product but you just completed it!!

BOOOOM!! 💥 💥

@rhwoodshop

4 жыл бұрын

What do you think Jake, is it a pretty good upgrade from the ones that we’ve made in the past

@JakeThompson

4 жыл бұрын

Rock-n H Woodshop That thing is a beast.. looks like you thought of everything on this one!! I like the paint job too!! 👍👍

@rhwoodshop

4 жыл бұрын

I tried. I’ve been thinking about it for a year.

This is a great project Drew! Would you recommend Armore more than K5? could you make a video pros y cons of this two pocket hole jigs? Seems like Armor will not allow to remove driver holes to make some fix or repairs. I am going to star with pocket holes. Not sure if I would need this function very often, but wonder which would be the best investent for long time.

After I experienced a vicious kickback cutting plexiglass, I will never do it again without a riving knife.

Nice work Buddy!

@rhwoodshop

4 жыл бұрын

Thanks Zach! I appreciate that.

@SouthernGinger

4 жыл бұрын

@@rhwoodshop you gonna be in ATL this week?

@rhwoodshop

4 жыл бұрын

Southern Ginger Workshop Unfortunately, no. I wasn’t invited to be a speaker so unfortunately I cannot afford to stop working and come down there. A lot of my annual business expenses came out the past couple of months so I’m a little strapped in the business funds right now.

@SouthernGinger

4 жыл бұрын

@@rhwoodshop totally understand, I'll have a drink for ya! :)

Drew can the armor auto jig be used with 1/2 12mm ply? I am only seeing settings for the 3/4 and up!😁🛫

Hi I brought this armor pocket hole jig it's nice I love it. Just a question with this jig it shows on the jig 1/2 " no colour for this setting it says use 3/4 screws. I like this jig well made.

@rhwoodshop

4 жыл бұрын

Use the 1 inch screws for half inch material. Thank You!!!

Im trying to figure out how to use a 1/2" birch plywood on my armor jig, but what drill bit would I use? The Kreg product has a mini for smaller screws. Does armor make one. I know about their mIniJig and thats not what Im talking about.

it's been almost a year since you posted this video. How is the Armor jig holding up? I am on the fence between this unit and the Kreg kit @ Lowes on clearance

As a godfather you make a great chippy

@rhwoodshop

4 жыл бұрын

Wow thank you very much. I haven’t heard the word chippy in a long time. I really appreciate it.

super cool vid. /\

@rhwoodshop

3 жыл бұрын

Thanks bro!

I am a hobbyist woodworker looking to pick up a cordless driver and a impact driver. I’m not necessarily looking for the best since I’m not a professional but I want tools that will have plenty of power when I need it, the batteries are going to last so I’m not constantly running out of charge, and tools that will will last and be dependable. I don’t want to buy cheap tools but don’t need the best. Can you recommend which tools to buy, brand and type of battery? Thanks.

Caught my eye you're using calipers with your Freud Dial-A-Width dado set. This blade set changed my life! I did a small initial setup adjustment and it's been dead on for several years now. I set it to their included fold-out chart and it's perfect every time. Do you find slop or variation with your set? BTW it's great to see you back on the scene! All the best, @HoneyOnWales

@rhwoodshop

4 жыл бұрын

I might have to look for that fold out chart. Thank you so much for taking the time to write me a comment and letting me know that you’re glad to see me back because I am super happy to be back!

@befmx31

4 жыл бұрын

@@rhwoodshop I second that! Glad you're back and thanks again for the Sketchup tutorials.

What degree of angle does this drill at and what kind of warranty does it come with ?

There a new link to this? Website doesn’t exist

Is there a reason I can’t access the plans thru Safari?

Drew, I don't follow why you had to use the stop block to cut the area for the drawer front under the jig. You already had an accurate make by using that WoodPecker thing-a-ma-jiggy. Can you shed some light here? Thanks.

@rhwoodshop

4 жыл бұрын

The woodpecker ruler got me exactly in the center but using the stop blocks on the cross cut sled keeps me from having to do tiny tiny tiny cuts to get it just the right size cutout. It’s just a huge timesaver to get the cut exactly accurate.

2 questions Where/how do you store it when not in use? Where does one get “Boom” glue?

@rhwoodshop

4 жыл бұрын

Well unfortunately I don’t have any boom glue for sale. 🤣 I do however have stickers you can put on your glue bottle. And I keep the cabinet inside my assembly table over my dovetail jig

@rhwoodshop

4 жыл бұрын

I do need to make a new drawer for it because this cabinet is bigger than my older cabinet and the drawer I made prior for that was made for the old cabinet so it’s a little too small

I wanna like Armor’s Toolboxes like this so how much cost let me know so I will buy Armor’s Cabinet Toolbox 2.0.

Where do you buy your t-track? I've been struggling to find them at any of my local big box stores.

@gbsk12

3 жыл бұрын

I got some T track on Amazon. Ali Express also has some.

@rhwoodshop

3 жыл бұрын

I have them in my amazon store. www.amazon.com/shop/rhwoodshop

What cnc machine are you using?

@rhwoodshop

3 жыл бұрын

It is a bench top unit called a “piranha”

What jig is this for? It dos not do a lot of good unless you have the jig to put in the cabinet.

@rhwoodshop

3 жыл бұрын

The “jig” is the armor tool self adjusting pocket screw jig. The red thing that’s in the cabinet in the video and thumbnail

@gbsk12

3 жыл бұрын

@@rhwoodshop Very nice. Thank you.

@rhwoodshop

3 жыл бұрын

No prob bob 😉

That's a pretty awesome cabinet. How does the Armor system compare to the Kreg in terms of total cost (screws, etc.) and are they compatible if you have a bung of Kreg screws? (I assume yes, other than having to figure out the length)

@rhwoodshop

4 жыл бұрын

I believe the armor tool jig is right around $179 but it comes with 350 screws that are all color-coded. If you have a bunch of Kreg screws that is OK because they are still all the same length. Armor Tool has a variety of sizes from 1 inch all the way up to 2 inch in course and fine thread. (1, 1 1/4, 1 1/2, 2) One of the big things though that make it very special is it takes all the guesswork out of using a jig like that.

@michaelmcdonough1989

4 жыл бұрын

As Drew stated you can use Kreg screws. Also I have found that eBay usually has better prices on Kreg screws than anyone else, especially if you need large quantities.

@rjtumble

4 жыл бұрын

@@rhwoodshop Excellent, thanks. I have the K4 and it works fine, but having to reach around the material to engage the clamp is a bother with plywood so I'll look at upgrading to this.

@rhwoodshop

4 жыл бұрын

rjtumble keep an eye on my Amazon affiliate page and you’ll find some product becoming available this week sometime. I know they are working on a brand new set of stock because they recently ran out. I got word yesterday that they hope to have more in this week

@rhwoodshop

4 жыл бұрын

rjtumble keep an eye on my Amazon affiliate page and you’ll find some product becoming available this week sometime. I know they are working on a brand new set of stock because they recently ran out. I got word yesterday that they hope to have more in this week

Website doesn’t work

Kreg foreman is better than any other pocket system pal!

dust collection??

@rhwoodshop

4 жыл бұрын

It comes with a dust chute that slides in and you can attach a hose to it

What state do you live in? I use to sell Kelly Moore products when I lived in Oregon.

@rhwoodshop

4 жыл бұрын

Oklahoma. Just a few minutes south of OKC.

@worldschaos2181

4 жыл бұрын

@@rhwoodshop is there a Kelly Moore dealer near you? That is way cool. I am now in southern California, but Kelly Moore is in the bay area.

@rhwoodshop

4 жыл бұрын

worldschaos2181 Yep there’s one about 15 minutes south of me

i wish they ship this internationaly :(

I think this take away one of the features of this jig which is the fact that is especially designed to be pair with 2x4s

Nice Drew, one more job well done !!! LZACCARO

@rhwoodshop

4 жыл бұрын

Thank You!!! I appreciate that

Nice! Can you make me one?

@rhwoodshop

3 жыл бұрын

I am contemplating making these for others that want it.

What happened to you?

why are you wearing gloves?

Has anyone noticed how many commercials that are being crammed down our throat by YoUTube?

@rhwoodshop

3 жыл бұрын

Sorry bro! View counts are going down too

@TheFalconJetDriver

3 жыл бұрын

I hate it for you, you have a great channel. It seems to me the algorithm that is being used is set up for maximum commercial exposure and fewer viewers so that they do not have to pay you for your content. Common sense says fewer views = less payout to content creators. However if they charge more for adds they can off set the fewer views. This is the same reasoning as carbon credits! 😫🛫

@LemonySnicket-EUC

3 жыл бұрын

@@TheFalconJetDriver I cast from my phone to my TV and the commercials are far and few between.

@TheFalconJetDriver

3 жыл бұрын

I broke down and started paying for the premium package of KZread 😩 but no mor commercials and that makes me happy.

Over time when you cut it close to size then recut to exact size your costing yourself and the cutomer alot of man hours. You must learn to be good enough or make a jig that make your cut perfect evertime cause if every cut is cut twice your losing alot. If you charge the cutomers over 10 1mil dollara for all the work you did you could have made two million dollars. Two cut is the most costly mistake you could ever make in the carpentey business. Trust in yourself a little more guy. You shouldn't have to cut every board twice just to get to the right measurements. "The famous rule measure twice cut once." Not cut measure once cut twice. Your costing yourself so much time and money but cutting twice.

Cabinet is slicker than whale dung in ice water...Nice job.

@rhwoodshop

3 жыл бұрын

That sounds disgusting and cool all at the same time. 🤣