I think you gave a very GOOD intro in comparing two different materials. thanks

Great video. I have been looking for this kind of material for RV use. Thanks

I just ordered the sample pack, I gotta see it to believe it! Thanks for the video!

Now you need a new dial caliper, ha. I love honeycomb design. Looks like a great product. I have the same sneakers, Walmart.

very good your videos. I'm building a camper and the information is very important.

Can these be screwed down like a typical plywood deck on a boat

What if you wanted to make a super light weight camper / Toy hauler trailer? Would this be able to withstand the flex and vibration of going down the road or supporting a large side by side supported by 16" center supports? Does it dent if you drop something on it, or smash the product in? Does this insulate too better than plywood? What's the R-Value equivalent of it? Could you put lets say a 1" or maybe 2" piece of this down for the floor off an Enclosed cargo trailer and then spray a Line-X type of coating over it and park heavy side by side or any other kind of off road vehicles on it without it sagging or crushing under the weight? That's what really makes me interested in it.

@CarbonCoreCorp

5 жыл бұрын

Several expedition vehicles have been made from these panels, R value is 3.3 per 1" of thickness in vertical position, and about 1 in horizontal position. Polyurea sticks great tho the fiberglass surface. Download the mechanical data sheet(laminated composite panels) from www.carbon-core.com, it lists several precalculated deflection values for different thicknesses.

@The_Original_forresttrump

Жыл бұрын

I’d say yes, ever see RV structural?

I'm needing a plywood to replace the flooring in a shuttle bus. The light weight and sound deadening sounds desirable for what I need. Do you think this product would work for me as a sub floor in a shuttle bus? It would be exposed to the elements of the road as the bus is being driven down the road.

Would you recommend this for building an enclosed trailer?

QUESTION: Has anyone (Mike?) found away to create seamless edge joints when bonding these panels to form a bigger sheet? I open to any guidance

How is boat hardware such as a console or T Top attached to this if I am replacing the deck core with it ?

how do you fasten the carbon core material together?

What a coincidence that I need to rebuild the substrate on an outdoor stainless steel workbench that has a leaky patch on it. I did a web search thinking there must be a honeycomb plastic materiel I can use for this. Turns out Carbon Core is my neighbor here in Troy, VA. We're not on the map for much here, so this is almost serendipity. I certainly never thought I would find these products 5 miles from me. Unfortunately after learning about the products, extreme weather plywood would be more economical for my needs since weight is not an issue for me. I am excited that this is a local business to me though! We love our local businesses here in Virginia!

@michaeljohnson-lv2ys

Жыл бұрын

awesome dude :)

@timboWVU

5 ай бұрын

Yea im in Richmond and it was 261 bucks to ship it here only 50 miles and i called and they said i can pick it up from the warehouse.

@SimplyRedVirginia

5 ай бұрын

@@timboWVU Shipping is outrageous. Over $200 for a $75 panel. But that would likely be the case for a sheet of plywood too. I imagine they have to crate this material or something to protect it. The gorillas that are the shipping industry can damage solid steel, let alone a sheet of honeycomb plastic. I had the company I work for look in to this material for substrate on outdoor stainless kitchen countertops. It would be a good alternative to exterior grade plywood. I dont know what the sample pack included that they ordered, but they wanted a sample of 3/4" thick. It would have to hold screws though. Not screws through it, but screws in to it to draw a countertop down to a cabinet. It also has to withstand adhesive without melting. The solution to the shipping would be to get the big home improvement chains to stock the stuff. I'd bet it would sell once people got familiar with it.

I need some 10 foot long for my second floor balcony deck. Will this hold up in bad weather?

You guys had me when I went to the website. The price per sheet was less than imagined, until I put in my zip code and seen the shipping cost which was more than twice the cost of the material.

@CarbonCoreCorp

4 жыл бұрын

Jacob, Need to blame the trucking industry for the freight costs. But these panels may be available from a distributor if there is one in your area, call us and we will try to find them locally for you. OF course, as you, know, it cost about the same to send 1 or 50 panels out with truck freight,so the more you order, the better price you have per sheet including freight.

@jacobj.1969

4 жыл бұрын

@@CarbonCoreCorp Yep that's the problem I only needed four of them. I get what you're saying. Freight and postal fees are making more money than all of us. In my business they eat up most of my profit margin cause I can't be competitive if I charge the customer shipping fees. I did find something akin to your product from another source, but I'm sure it was not as well made as your product and I am already having regrets. Next boat build I really want to use your honeycomb composite ...no more compromises!

I'm so glad I found this video. It will be so help when I build out my van for camping. The polycarbonate will save so much weight. 🤑🤑🤑👍👍👍

@Gantzz321

4 жыл бұрын

camper shell or interior walls and cabinets?

@lani1life

4 жыл бұрын

@@Gantzz321 interior walls and cabinetry.

@adrianafonso754

3 жыл бұрын

Are you avoiding plywood throughout your whole conversion? I was looking for an alternative material to ply which was fully waterproof for all panelling walls, floor and ceiling and I think this might be the solution.

@lani1life

3 жыл бұрын

@@adrianafonso754 yes.

@adrianafonso754

3 жыл бұрын

Lani C hey how are you getting on with the conversion? How are you sticking the honeycomb on to the walls? Rivnut directly on to metal ribs? Thank you!

Hi, Was the floor damaged because of wood rot , impact or tensile failure? Do you know the thickness of the plywood floor that was damaged?

Can this be used for lightweight cubby type cabinets for an enclosed trailer?

Yes! I would love to build a DIY truck camper from this material. Where do I buy it?

Will this work for house roof decking?

That hammer test demonstrated the high density of the marine ply over the foam core. There are specifications that list the equivalent of ply wood verses foam core; 9mm marine ply is equivalent to 34oz (1kg per m2) /20mm foam core/ 34 oz with the foam core weighing approx. 6kg/m2. 9mm ply weighs approx 5.3kg/m2. Even when skinned with 6oz cloth and resin, it still comes around the same 6kg/m2. Foam loses on every score except stiffness. Meaning ply needs more stringers or inbuilt structural support from furniture, cupboards etc, or the addition a carbon skinning. Cheers

I would love to rebuild the interior of my 24 foot sailboat using this material!Wondering if I can get it on the west coast.

@CarbonCoreCorp

3 жыл бұрын

Of course, we ship to west coast regularily

@CarbonCoreCorp

3 жыл бұрын

Of course, we ship to west coast regularly

@jankline2542

2 жыл бұрын

What's the biggest sheet you can get@@CarbonCoreCorp

@CarbonCoreCorp

2 жыл бұрын

@@jankline2542 10x50 feet

Fatal flaw you can't scarf the boards which is a much better method than butt joints. So you'd still be making the majority of the weight of a boat through the hull. BUT, you could use this to make anything from the deck up. This would be an excellent material for making Jon to bass boat conversions much lighter.

@usedcarsokinawa

2 жыл бұрын

You’ll fiberglass either joint so it would become one panel.

@Richard-nb4iv

4 ай бұрын

For butt joints, one can remove the honey comb to a desired depth on each butt and add a core to bond both panels together, if done right, could be just as good or better than a scarf joint?

@Carbon-Core Corp. If you use this in a cuddy cabin rebuild, do you have to encapsulate it with fiberglass? Or, is it waterproof as a stand alone?

@CarbonCoreCorp

2 жыл бұрын

it is already encapsulated, no need to encapsulate this, stand alone product is waterproof

Great info, thanks! Do you have 1/8" thick 4 x 8 sheets that would work for exterior RV panels?

@The_Original_forresttrump

Жыл бұрын

Good point and interior panels too.

I have built several plywood and cedar strip boats over the past 30 yrs. I have also built an all wood jon boat. My question is how does this material hold up to impacts and direct scrapes from, say rocks. I have found that same boats built in plywood covered in fiberglass take impact better than straight strips of wood covered in fiberglass. The plywood boat weighs more but holds up to impacts better. In the case of my jon boats, the planks were 3/4" pine boards and the boat was 22' long and 4' wide. When built in plywood I can use thinner plywood and cover it in fiberglass inside and out. This keeps my weight down, extends the life of the boat and takes impacts and scrapes very well. By far though the all wood boat with no fiberglass has the best sound dampening in my opinion. I have hit huge rocks mid stream just under the surface of the water and only had minor damage. Usually only to the paint. As another gentleman said scarfing is used allot in building boats and this could prove challenging. Butt blocks could be used of course but this is added weight. I can definitely see the benefit of using this on the interior components such as bulk heads, berths furniture and sub decks. I think a good couple of controlled test of scrapes and impacts would be helpful for your buyers. Like I said I would use this product on interiors but I'm not sold for it on the hull. The hull is just one part of a boat so allot of weight could be saved using this product above the waterline. All this is just my opinion based on my experience with building boats over the years. The larger a boat the more damage it causes and receives when on impacts and scrapes. Of course the thickness of materials will increase with size of the boat. Thanks for showing your product. I would like to try some just to compare. I would use a thickness of plywood that had equal deflection as your fiber core product. Of course this is after the plywood has been glassed inside and out. I believe this would give more of an accurate comparison. This is the same as when I build the jon boats . The one with plywood is built with thinner planks. This keeps the weight down but I gained in strength. Just some food for thoughts. I would love to hear your input or anyone else's input who has used your product.

Thanks buddy. I’m researching the right panel for this 4 foot speed square/ cutting jig for chopping plywood for home construction. I’m gonna be a millionaire

Thank you. Great information. I would like to see an impact and/or hammer test to see how this honeycomb polyethylene material holds up as compared to plywood. The honeycomb polyethylene panels are also use to construct road-cases to be used to store 88 key electronic keyboards and all other cases involved in the music industry that are packed in semi-trucks for a concert. Would really like to see how this material holds up to the industry wear and tear. Thank you kindly.

What’s the best way to cut coroplast?

How do you fiberglass over the panel? Does the fiberglass on it have laminating resin or does it need to ground before adding glass overtop?

@CarbonCoreCorp

5 жыл бұрын

It should be lightly sanded before laminating over it

Hello from Argentina! O have a question, This honeycomb board can be used for a "boat deck" that goes down the floor? Instead of wood, because its an old boat and the structure that hold the floor is made of wood and it's all rotten. Thanks for the advice

@CarbonCoreCorp

4 жыл бұрын

Gaston, Absolutely, boat deck is very common use for this product, hundreds of OEM builders use this construction method

I love this stuff!

How do I get in touch for a technical question? I need to build a thin piece think catamaran wing, as thin as possible. If I wanted to have a tube structure say 2" o.d. a little inside of the edges for structure and flexion control, how manipulatable is this product? I'm trying to re-work a sandwich composite over foam idead and am thinking about flex over a long edge on two sides of a very lightweight platform. Is there a way to bend it without compromising strength, would I need to cnc some pieces to sandwich around the metal to meet up with the two surface pieces kind of an intricate idea and this looks like it could reduce my weight substantially vs wood

@CarbonCoreCorp

3 жыл бұрын

Please check our website carbon-core.com for contact info and contact us directly

Restance to uv? I am replacing the wood floor I installed in my 16 foot Princecraft Starfish. Also wear and tear from walking on this material. Oh and, slippery when wet? I sealed some sand ontop of the ply to prevent the coated surface from being slippery.

@CarbonCoreCorp

3 жыл бұрын

These panels are made with UV resistant gelcoat. Wear characteristics are great, somewhat slippery when wet, but easy to coat with nonskid coating.

Greetings and thanks for the video, Listen, this product seems great despite the cost (especially with shipping). But that being the case, now we potential customers who are seriously considering the product need some direct clear answers to our concerns which throughout the comments section have been vaguely replied to if at all by Carbon-Core Corp. (for the record, visiting the website or after calling the technicians/representatives some questions still haven't been definitively answered). Can you all perhaps make an updated video on using fasteners such as screws, bolts, nails, threaded inserts (ATR pins etc.)...and which will and will not work and the stress limitations of each? Also, any suggestions on best way to deal with the cut edges if one wants to make a panel or lid with hinges (i.e., should we carve out the honeycomb edge and epoxy in a strip of wood or pvc, or use construction adhesive to glue on a section of aluminum c-channel over the edge, or just fill in some epoxy or bondo the edge, sand, and then place the screwed hinges in directly)?? My longwinded point is, PLEASE HELP US OUT by making a updated video addressing how to overcome these issues. You will definitely be compensated/rewarded well for making said new video....from all of the business you will gain from the multitude of us whose only hesitation is what was covered in this lecture i just wrote. lol!

@danmatelsky6064

Жыл бұрын

I just met someone who thinks like me. Exactely my ?'s also.

@MrJhchrist

Жыл бұрын

@@danmatelsky6064 There's so many of us, like 3's of us!

@somestuffithoughtyoumightl6985

Жыл бұрын

Can think of a lot of applications for a lighter weight, waterproof building solution.

Cool explanation! Cheers 🥂!

@burtisaac1000

2 жыл бұрын

What about fire 🔥 resistance? Interesting 🤔 plastic vs wood 🪵. What type of material makes honeycomb plastic different from wood 🪵?

I would like to use this on my pontoon boat I am rebuilding. How will it hold up and what is life expectancy? Can I get this in California?

Great video. I'm looking for a light weight alternative to plywood decking for my enclosed car trailer. Would this be strong enough for that application?

@richardhenry371

3 жыл бұрын

I guess they did not answer

@freeman6147

2 жыл бұрын

@@richardhenry371 Answer is probably "NO"

@travismiller5548

Жыл бұрын

did you not see they guy standing on it?

If I build a deck out of the honeycomb, can I glass over it to make it blend to the boat itself. Doing a skiff and I want the front and back deck to be level with the top of the boat.

@CarbonCoreCorp

4 жыл бұрын

Absolutely, most customers who buy these panels for deck repair do that.

I just need a 4x8 sheet for my project. How would I order one?

can you make an entire boat hull with it?

How does Carbon Core accept nails and screws going through the board and onto the stringers? What about the compression at the small area of the heads of nails or screws? Is each cell in the Carbon Core guaranteed to be sealed and waterproof, and what of the butting of panels ... any special needs? How does 3/4" Carbon Core compare to 3/4 inch marine plywood, in a collision situation?

Has carbon-core ever sold precut/finished edge product?

Is this product able to be cut down to size with a circular saw? I apologize if this sounds redundant, I'm just trying to figure how to apply it to my own needs. Thank you in advance!

@CarbonCoreCorp

2 жыл бұрын

Yes, all woodworking tools work fine with our material, it is more abrasive though

@CosmicSeeker69

Жыл бұрын

reverse your circular saw blade for cutting plastics ;)

I wonder what the insulation rating is as well considering it looks like a paper honeycomb loom inside. May be better as well. Curious if it is efficient there as well, if it could be used as an rv floor base material. Does it have a higher water resistance than natural plywood? Lots of other tests to do but really cool product.

@CarbonCoreCorp

7 ай бұрын

R value 3.3 per inch of thickness in vertical position. Al lot more info regarding that subject on our website.

Can you build a swim grid out of the plastic panel to replace a teak swim grid?

@CarbonCoreCorp

4 жыл бұрын

Yes of course. Most OEM boats are built with plastic and not wood.

Can HoneyComb board be used for Bulkheads and is it compatible to Vinylester & Polyester resin?

@CarbonCoreCorp

5 жыл бұрын

Yes, bulkheads are a common use for this material and our Composite Structural panels are compatible with VE and PE resins

Cool! Thank you!

Can i put these on a 53ft trailer

Hello I am looking for some sort of flexible sheeting that isnt corplast but has similar characteristic to be able to flex and form an arch the long way with about 4 feet between the ends once bent..i am trying to build a bike towable camper..thanks any ideas are helpful make

@CarbonCoreCorp

3 жыл бұрын

on our website you will find flexible plastic honeycomb sheets, that should work for you

how do you seam the edges when using multiple panel's?

@dcdc1970

2 жыл бұрын

another great question

@dcdc1970

2 жыл бұрын

@@Good Will Hunting thus adding to the cost

@CosmicSeeker69

Жыл бұрын

darn it - THAT'S my question too. I'm guessing some form of welding...ha, it got answered by Tom Brayton late '21

@steveturansky9031

Жыл бұрын

I would think you would core out one panel's edge (make it female). Remove the glass laminate from the other panel's edge (make it the male). Glue those edges and insert the male into female. Then tape both sides with fiberglass. You would have a bit of a bulge because the taped area would be thicker, but this would be strong.

How do you bend this stuff?? I want to make a hard top for our 1956 42" Matthews and need to keep it lightweight.

@CarbonCoreCorp

4 жыл бұрын

Christine, Great question. You can score bottomside, perhaps every 6-8”.Regular circular saw set at 1/16” depth, fine tooth blade

@christinelabrie1430

4 жыл бұрын

@@CarbonCoreCorp Thanks so much!!

Im thinking of building a truck.camper out of the ¾ Material. Would you know the insulation value? And would I be able to use any fiberglass resin to joim the panels?

@CarbonCoreCorp

2 жыл бұрын

R value is 3.3 per inch of thickness in vertical position and yes you can use resin to join them.

Any videos of finished applications, customer products?

@CarbonCoreCorp

4 жыл бұрын

No videos, but there may be some photos of customer applications on our website. We try to keep our customers projects confidential for their protection.

What about breakdown in the Florida sun over 20y? Any off gassing ? Is any part of this product from recycled materials? Will screws be a secure as they are in wood? Can it be used in a small house build in place of wood sheathing?.. and the 1M question.. price comparison?

@CarbonCoreCorp

2 жыл бұрын

There is no off gassing, no recycled materials used in our production currently. Screw retention is obviously not the same as wood, but you can get close to same values with right type of fastener. You can check the prices on our website, but no light weight composite material is comparable to wood prices. Boats have been built for 40 years from this material with large percentage of them residing in Florida. There is a reason boats are not built out of wood for a long time.

Can this material be used as an engine hatch? Mine presently is crazy heavy plywood. Thanks

@CarbonCoreCorp

8 ай бұрын

Sure thing, common use for this material.

Hi, I am interested in these panels can I cut them with a jigsaw or a circular saw also is there some kind of bonding glue or epoxy that will permanently bond them, And how do you order? I’m building a camper trailer and like the rigidity and the weight these offer .

@CosmicSeeker69

Жыл бұрын

too late now - but reverse your circular saw blade for cutting plastics

Please share a link to this product demonstrated here.

how can I get your product and not spend $250 on shipping? Near Charlotte NC

Good info - cheers

Marine plywood is not coated with fiberglass on a pontoon boat. It is just screwed down. But your product looks nice. On a pontoon boat, numerous holes are drilled through it for rails, wires, control cables, seats and accessories. Will your product allow water into the cells once it is drilled?

@TheThomaswastaken

3 жыл бұрын

No. Each cell is separate from the others.

great product i would use it to build the walls of a houseboat

what type of plastic? Will it bond with fiberglass? Is it safe to cut with a laser (no pvc or epoxy)?

@CarbonCoreCorp

7 ай бұрын

Skins are fiberglass and fiberglass bonds well to fiberglass. Top layer of honeycomb is polyester which bonds to fiberglass great.

could you build a flying copy of the spruce goose out of it?

I would like to try that one

Cool stuff

Do you have instructions on creating a curved surface using the plastic? Say a camper for bicycles. This will reduce the weight but not sure I can bend it without break it.

@CarbonCoreCorp

3 жыл бұрын

Hello, not easy to create a curved surface with this panel, probably should use unlaminated honeycomb in mold to create curved surface

stitch and glue?

I'm in Virginia and I'm interested in come by to check this stuff out and buy some. Bec I just got old airstream and it has no floors in it

Hi ! I'm in the wheelchair and damaged my van floor twice, with plywood base, so I'm looking for a different solution. Could this be a valid alternative, strong enough and water resistant ?

@Texaca

3 жыл бұрын

...add another layer of plywood, sandwich them together with epoxy. Maybe the original panel in your van was too thin?

@syncrovanCos

3 жыл бұрын

@@Texaca Not necessary. Most probably, water infiltrations, leaks from the dog bottle and so on. That combined with heavy wheelchair, disaster ensured.

@TheThomaswastaken

3 жыл бұрын

@@syncrovanCos You can seal the wood from water with a layer of epoxy. I work with the honeycomb material advertised, I can't see any reason to avoid it in your application. It's not great at heat resistance, melts at boiling temp, but that should not be an issue inside a vehicle.

@syncrovanCos

3 жыл бұрын

@@TheThomaswastaken Indeed, this could also be a valid option, since last time I didn't apply any protection for the wood ! In theory, if it was well protected, should not get damaged by the water, even in case of infiltration.

Can you screw into this and how does the pullout strength compare

@CarbonCoreCorp

3 жыл бұрын

yes, but this needs a very specific answer, please contact our sales engineers through our website

Only negative thing I’ve been hearing about honeycomb for boat floors is it’s tough to screw into if your trying to add a tower . Or anything that needs to be structurally secured.

@CarbonCoreCorp

4 жыл бұрын

Steven, you are correct. Adhesive bonding and sheet metal type screws are is a commonly used technique to address that problem and larger backing plates can also be used effectively. Usually the extra effort is worth the reduced weight.

@JS-rp7qb

4 жыл бұрын

Make fiberglass backing plates about .25” or thicker

@CosmicSeeker69

Жыл бұрын

bonding - full length strength vs point contact

Decomposition time?

how does it react to a gas spill if filling your tank and accidently over fill.

@CarbonCoreCorp

Жыл бұрын

Hello, Our honeycomb is made of copolymer polypropylene, one of the most chemically resistant materials available.

could not help but notice you didn't do an impact test. Also an R-value test. Have you had any customers use your products to fabricate campers?

@CarbonCoreCorp

4 жыл бұрын

Greg, This was meant to be a visual representation on deflection test in real world conditions, outside of a lab. For test results in impact, R value, tensile etc. please consult with our website, and the product data sheet at www.carbon-core.com Impact strength is one of the strongest part of this panel , R values are 3.3 per 1" of thickness in vertical position.

Yes it is

I want to use that core as the floor of a johnboat. Ribs are spaced at just about 12".

I went to see how much shipping would be. It said shipping would be 195 dollars. That was more than the two or three sheets I would need. So sad. I thought the light weight made shipping less. Can I pick it up myself? Where is it located?

@CarbonCoreCorp

2 жыл бұрын

You are welcome to pick up yourself or with your carrier, we are in Virginia, near Charlottesville.

@KangaAndTwoRoos

2 жыл бұрын

@@CarbonCoreCorp I wish I could. I hope to go to Maryland in August, but unfortunately I have to have the floor down before then. Maybe next time.

Dude You rock!!! Great info. Can you line the cuts with something to avoid exposure to the honeycomb?

@CarbonCoreCorp

4 жыл бұрын

Thank you, and yes, depending on your application, aluminum extrusions work good, or one can rout out some HC and fill with putty, or thickened resin.

@hellapellanyc6465

2 ай бұрын

@@CarbonCoreCorp Can a poly glue work as well in a caulk tube like pl premium or something of the sort that one can still epoxy over or take poly resin over?

Can it even be applied in building a teardrop trailer too cut weight

@CarbonCoreCorp

3 жыл бұрын

For flat areas,like floors, absolutely. FOr curved areas consider our core that is scored and made flexible, without the lamination.

sheet cost of both?

ok its lighter ... is it more cost effective ... as in same or lower price to the marine plywood lamination ...

@CarbonCoreCorp

2 жыл бұрын

No artificial lightweight engineered materials are ever lower price than wood. Lightweight no rot construction pays for itself over short period of ownership costs.

I have been looking for something like this but I need a 5 foot by 12 foot do you offer that size

@CarbonCoreCorp

4 жыл бұрын

We meke these panels up to 10x50, MOQ is 500 sq ft on custom size panels

@theprojectproject01

4 жыл бұрын

So one sheet of 10x50 hits the MOQ? Sweet.

how can used ? nail, glue, screw? can make something ensambled?

@CarbonCoreCorp

4 жыл бұрын

Yes Sir, all of the above, depending on what you are building.Check out our website for detailed drawings how to assemble structures.

How could you incorporate this in to a transom just to hold a 50hp 4 stroke motor

For clarity, to use as deck or add a false floor (my case) in a boat, the surface IS already fiberglassed so it's simply a matter to add fiberglass & resin at edges to attach/fair into the sides of the boat? Also, is the 19mm stiff enough as is, or would it ideally need stringers to support it underneath? Thanks.

@CarbonCoreCorp

3 жыл бұрын

You are correct, download product data sheet from our website, for composite panels, it will detail bending stiffnesses based on thickness or call us and we will help calculate the correct thickness for you

does the honey comb come in 3/8" thickness? Surprisingly my deck is 3/8" plywood , resin on the under side...and several layers of mat on top with gelcoat

@CarbonCoreCorp

4 жыл бұрын

Yes it does

What is the r value of the 1/2" and 3/4" ? Is 5/8" available ?

@CarbonCoreCorp

2 жыл бұрын

R value is 3.3 per inch of thickness

Is it possible to pick up an order to save on shipping cost?

@CarbonCoreCorp

Жыл бұрын

yes

Price comparison to plywood?

On tropical island this is used for kitchen cabinets, wood on tropical island rot termites and a there little critters eat the wood,not PVC

What about screwing into it? What about glue? It doesn't matter if it lighter if you can't use common fasterners

And the plywood flexes 1/64 th after it has skin on both sides 🙂🙂 And how much are those plastic panels? Would be nice to compare the two .

@CarbonCoreCorp

3 жыл бұрын

please check our website for current pricing

@bizim_eller

3 жыл бұрын

@@CarbonCoreCorp will do, thx👍

Honey comb will still need resin and a layer of glass on both sides for strength which will and some weight. You should notate that in your description. It will still be lighter than wood.

@CarbonCoreCorp

4 жыл бұрын

All our weight and calculations for our panel have the resin and glass weight already included. Honeycomb by itself without the glass and resin would weight only 13 # for 1" panel 4x8 size.

@hellapellanyc6465

2 ай бұрын

@@CarbonCoreCorp Hi what type of cloth is used on the laminated panels? and what is the weight of 1" panel 4x8 laminated?

Yes Sir, our honeycomb is compatible with both resins and thousands of boat bulkheads have been successfully built with our core material.

@gevorgnazaryan8720

3 жыл бұрын

I am looking to build a sleeping platform at the back of my first. I’ve seen people use plywood to level the sleeping surface. Will your product work just as well while reducing the weight? If so, Which type should I buy? Thank you very much in advance.

@CarbonCoreCorp

3 жыл бұрын

@@gevorgnazaryan8720 Absolutely, if you call our office, we could run calculations, that depend on how you support the panel, but typically, 25 mm, or 1" panel should work fine for what you do.

Where can we purchase it? Your website have no pricing. Yes it have information and data but why don't you have online ordering service?

@CarbonCoreCorp

3 жыл бұрын

our website, online ordering section and it has pricing there.

Can I fiberglass supports to this product?

@CarbonCoreCorp

3 жыл бұрын

You can fiberglass directly on to the skins, they are Isopthalic polyester resin based.

Are these panels available in Queensland Australia?

@tandyten1148

2 жыл бұрын

Yes in Brisbane

@CarbonCoreCorp

2 жыл бұрын

Currently, no, we have no distributors in Australia

What’s the exact name of this product on your website, I would like to takeout the wood casting deck I put on my Jon boat and add this

@CarbonCoreCorp

2 жыл бұрын

composite laminated panekls

@amateuroutdoorproductions7044

2 жыл бұрын

@@CarbonCoreCorp can you use screws with this

@CarbonCoreCorp

2 жыл бұрын

@@amateuroutdoorproductions7044 you can but recommend sheetmetal thread screws as skins are on the thin side

An eight of an inch 1/8" is .125", not about .200".