Plasti Dipped My whole Car! DIY
Автокөліктер мен көлік құралдары
In today's video I'm showing you the process of Plasti dipping my Honda Civic hatch back.
Make sure you do very light coats at first then wait 20 minutes till the next coat. I did 4 coats on this car but make sure you do at least 3-5 coats.
Hoped you guys like this update on my hatch let me know what you think of the color. A lot more videos to come.
Пікірлер: 233
Pretty cool! I think it’s nice to see people just experiment an learn ! Good on you!!! 🤘🏼😇
Pretty good job being done with the cans. However to avoid the plastidip from peeling with the tape, take the tape off when the dip is still super wet. Those areas are considered peel when wet areas. Other than that it turned out super good
They used to be $6-7 a can. And now under Senile Joe, they're over $14 a can
@aaaaaa-hd7zp
2 ай бұрын
They're $8 at home Depot so stop spreading wrong info just cause you're daddy the Cheeto is going to prison
Also the areas where u have the rubber trim u dont want to tape all the rubber trim up.. leave some and let the plasti dip be able to bond fully into the gap between the body and rubber.. that way when u do peel it the bond should break within the gap and not peel from the area where the OEM paint is.. a few other small mistakes were when u did the roof.. tough to do with a can.. but try and keep the can pointing straight down not angled to prevent over spray and spray as much of the roof as u can from 1 side then walk around and continue from the same line where u left off.. this will help minimize the stripping. but for doing it with just cans looks great...
@JohnnyFabz
5 жыл бұрын
Thanks I now know more from doing it. Always room for improvements
Love this new color ! You did a really good job ! I have one question for you : How many cans did you needed for the whole 4 coats on the whole car ? Thank you for the answer ! Bye
@JohnnyFabz
5 жыл бұрын
I can’t remember now but I think like 15 you can see all the can in the intro
Looks brand new bro great job
@JohnnyFabz
6 жыл бұрын
The Wolf thanks
You actually did pretty good with just cans 👍🏼
@JohnnyFabz
6 жыл бұрын
Blâncø thanks
@jaycarter1241
6 жыл бұрын
Blâncø agreed
@davidr1122
4 жыл бұрын
Cans are tough, this is really really good for using cans. I personally use the wagner gun.
Nice i do like how it came out. How many cans would u say id need for both my front and back bumper? Bought 3 but i feel like that may not be enough
Looks good! I would be happy with that job compared to my paint peeling every where. I might try this.
Much props for you attempting and then the job you did. Probably using the handle and nozzle from dyc may have helped, however good job with the cans.
Quality video, like how you did the beginning and the end with the garage door 😂
@JohnnyFabz
6 жыл бұрын
Corey Sanchez thanks bro 🤙🏿
Great video buddy!
Very good job for a young man , a big transformation for a low budget
Came out good. Cool video
@JohnnyFabz
3 жыл бұрын
Thanks
Actually, you shouldn't do "light" coats. that's how you get the "orange peel" texture issue. You should spray it slower and do a wet coat, but not enough to avoid running. Then once it dries it will be smooth and ready for a second and third coat. Also, be mindful of your taping, and pulling the tape once its dry, you can easily get that edge issue around the windows, you can run an exacto very lightly around the edge of the trim before peeling the tape to give you a clean edge. Good job on a first time around though! p.s. you need 3-4 coats before you can easily peel it off in one grip otherwise you'll be there ALL day picking and peeling little bits at a time.
Actually looks nice, good vid bro
@JohnnyFabz
5 жыл бұрын
Thanks man!
Thankyou for doing this video, you did a very good job using spray cans, Im going to try it on my grandsons car that needs a paintjob😊
@DrPigment
4 жыл бұрын
kenyaaaaaa there is a much better way. Promise this isn’t a spam comment. Less time and money. Send us a message when you’re ready.
@Hephzibahh
4 жыл бұрын
@@DrPigment ok
@slow_rednline4874
4 жыл бұрын
@@Hephzibahh don't bother .. they are trash..just use dipyourcar.com and look there..if it's still owned by the same people .. don't fucking bother..personal experience
Nice job , I think if you used the plasti dip glossser it would make it more naturally shinny rather than the dull Matt
Hell yeah looks nice 👍🏽
Hi, how thing went after - was result satisfying for long period of time?
Good start buudy
@JohnnyFabz
5 жыл бұрын
Thanks
Did you have to Send prior to spraying the plasti dip?
how good is the Quality in your experience and how long does it last?
how much was consumed by the aerosol can?:)
Thinking of doing this
1. Solid first run. Keep it up. 2. That background music is super catchy.
How long did it take to dry?
Is the paint still good today?
Buddy it looks good I'm going to do the same thing to my 2003 huyndia elantra lo matted black
@garriga24
5 жыл бұрын
How many cans did you use
@anthonyquiroz1998
5 жыл бұрын
@@garriga24 I used 12 cans
@garriga24
5 жыл бұрын
@@anthonyquiroz1998 how easy will it come off ?
@anthonyquiroz1998
5 жыл бұрын
@@garriga24 it comes off in large sections
@garriga24
5 жыл бұрын
i'm doing this on my 01 elantra!!! can't wait to repaint it with the dip
You’ve gotta wait a while between coats, that’s why the paint ran and there was striping. Plus also distance with the can and such
@user-pz4mv9lg8e
6 жыл бұрын
ItsYaBoyOats 24344566
@Nikosakii
Жыл бұрын
He said he waited 20 minutes
What color did you use? Gun metal gray?
Bro, what kind of tape is that?
Does it do good in car washes ?
looks like primer tho
@JohnnyFabz
3 жыл бұрын
Car has been painted sense this video
How does it look after some time ?
That's pretty awesome how long did it take you and how many cans did you end up using
@JohnnyFabz
6 жыл бұрын
jovanni figueroa 10-15 cans about 4 hours on and off
@DrPigment
4 жыл бұрын
jovanni there is a much better way. Promise this isn’t a spam comment. Less time and money. Send us a message when you’re ready.
ya supposed to peel the tape off when its wet on the last coat..
@sjonesy6185
5 жыл бұрын
Facts
How many cans do you recommend for my 18 wheeler ?
How many cans did you end up using?
I want to know why he spent all that time to tape off but dident cover everything all the way. I use plastic dip alot it will juat peel right off where the seam line is
@JohnnyFabz
5 жыл бұрын
Yeah I know know I did have to
How many cans do I use
Why tape it if it peels off?
Throw tint on window and led kits headlight and jdm yellow foglight
It's five years later, how has this dip lasted?
Nice job! How plasti dip spray spend?
@rebelionz_3200
4 жыл бұрын
He probly spend about $100 Plasti dip itself
Hey the car came out pretty cool. You said you used 11 cans but is that enough paint or did you use enough plasti dip in order to be able to peel it off in the future. I heard you have to apply a certain amount in order to be able to peel it off correctly if not you will hella struggle to take off.
@JohnnyFabz
5 жыл бұрын
crazyassjerk214 I did three coats. Pealed off good when I tryed it on one of my fenders. It came off in almost one big piece
@crazyassjerk214
5 жыл бұрын
So you managed to pill off in big pieces with just 11 cans? Cool. I’m wanting to cover my 08 impala with black spray can plasti dip as well. Any hints on how many cans of plasti dip I’ll need ? It being a 4 door sedan.
@JohnnyFabz
5 жыл бұрын
If I was going to get it again I’d just buy a gallon
@DrPigment
4 жыл бұрын
there is a much better way. Promise this isn’t a spam comment. Less time and money. Send us a message when you’re ready.
@slow_rednline4874
4 жыл бұрын
@@crazyassjerk214 don't be an idiot buy spend 400 and get a sprayer and 4 gallons of black..this was just stupid to do 🤦🏾♂️
How many cans it take
Why would you use a primer color for your color? You should have used Matte Black.
Your finger must be killing you bro. Great job for cans. Carbon fiber hood would be perfect touch. Plus add window tint and it will be boss.
@JohnnyFabz
5 жыл бұрын
Thanks man it did start hurt for sure lol
@hellow9155
3 жыл бұрын
I used to use a coin with a rubber bands to hold it to my finger so its not having all the pressure at one point in my finger and causing fatigue
Earned a sub
@JohnnyFabz
4 жыл бұрын
Thanks for the support🙌🏼 check out the new videos!
Whats the song name in the intro?
Looks just like unsanded primer......😁
@alyxskyler
4 жыл бұрын
Because of the color?
Great work dude.....can you please calculate how many cans you used for just the hood and the front bumper?????i want to dip mine and i don't know how many cans i'm gonna need......i saw that you dipped the whole car with 13 cans...so i think that 6 would be fine!!!!!what do you think????its the hyundai Tiburon on the picture...
@JohnnyFabz
5 жыл бұрын
EDDIE- G21 probably more like 3 cans
@eddie-g2143
5 жыл бұрын
@@JohnnyFabz thanks man.........3 cans for both?????bumper and hood????
@DrPigment
4 жыл бұрын
EDDIE- there is a much better way. Promise this isn’t a spam comment. Less time and money. Send us a message when you’re ready.
Sprayed it on way too thin, good luck getting that off later
good job, how many cans did you use for this?
@JohnnyFabz
4 жыл бұрын
Believe it was under 15
@angelossioulas4529
4 жыл бұрын
@@JohnnyFabz well played! 2 times whole car or 3?
Surprised out of a can, prep is the main thing to make it look professional...waw cans,
Love this🇵🇬
How long did it last?if i am dipping i want it on there for at least 4 years
@erickq123
4 жыл бұрын
Nah man this dont last anywhere that long maybe 8 months if youre lucky
@DrPigment
4 жыл бұрын
smokah there is a much better way. Promise this isn’t a spam comment. Less time and money. Send us a message when you’re ready.
How many cans you recommend for a sedan
@09ThunderOne
4 жыл бұрын
Henry O. Don't use cans. Get a proper spray gun from DYC.
How many cans did you use?
@DrPigment
4 жыл бұрын
there is a much better way. Promise this isn’t a spam comment. Less time and money. Send us a message when you’re ready.
Nice 👍🏽
@JohnnyFabz
3 жыл бұрын
Thank you
Dude if you're going to plasti dip your car do it right go online look up dyc and do it right Fonzie has so many videos of tutorials that teaches you pretty much how to do it yourself if you do exactly what he says it'll come out immaculate
How long did it take?
@DrPigment
4 жыл бұрын
Anthony . there is a much better way. Promise this isn’t a spam comment. Less time and money. Send us a message when you’re ready.
Your going to hate it when peeling off I used about 20 cans and the shit wont peel off for shit. I have to sand it completely down
Rip lungs
How many cans did this take to do
@DrPigment
4 жыл бұрын
Trial BY there is a much better way. Promise this isn’t a spam comment. Less time and money. Send us a message when you’re ready.
When does the color paint plasti dip start wearing off?
@ScollayTable
6 жыл бұрын
Arlene Nicole never wears off if its done properly. I live in Massachusetts and snow or heat the color look the same. Visit dipyourcar for more information
@tjtomax
6 жыл бұрын
did a colorshifting pearl in plastidip on my miata. been on for 2 years now. the color doesn't fade, but bug splatters are a pain, because they get embedded into the dip. you can't get the bug stains out without a lubricating cleaning product, and some cleaning products can put ugly stripes on the dip. just gotta take care of the thing
Good job on the experiment buuuuuuuut that will be a pain peeling off knowing it looked like you used only about 10 cans
how many on galons i need to dip my civic...
@JohnnyFabz
5 жыл бұрын
I’d say probably 1
@DrPigment
4 жыл бұрын
there is a much better way. Promise this isn’t a spam comment. Less time and money. Send us a message when you’re ready.
👍
Damn it looks good , let me ask .. This was a few months ago , how does it look now ? Is it durable and washable?
@JohnnyFabz
6 жыл бұрын
chamucoboy 96 has held up good for what it is. Have washed it once a week no issues. Where the car was rusty it has bleed threw a little.
@senorchamuco2955
6 жыл бұрын
Alright thanks bro , good job btw 🤟🤙
@JohnnyFabz
6 жыл бұрын
chamucoboy 96 thanks man share this video if it helped
How many cans did it take
@JohnnyFabz
4 жыл бұрын
15 or so
@JoshuaBelton
4 жыл бұрын
@@JohnnyFabz Thanks
My Friend Primero no cubriste los cristales, ópticas, y las gomas parcialmente. 2° la pintura que aplicaste en vez de mejorar empeoró la imagen del auto. 3° Hubieras comprado una buena pasta de pulir que ibas a conseguir mejores resultados. Consejo: buscar un pinto o conseguir mas dinero para reparar lo que hiciste.
@DERBRSKA
6 жыл бұрын
Gabriel Kutz mas despacio cerebrito
Not having garage makes things seem impossible 😢
You have a booth and professional equipment available to you... Why did you decide to use the aerosols? That's never gonna peel properly.
@JohnnyFabz
5 жыл бұрын
I pealed a whole fender off no problem. So I’m sure the rest of the car will be fine when I actually go to paint it
Slammed tf out that door lmaon
Look at the camera lens
@JohnnyFabz
5 жыл бұрын
Yeah I have to work on that for sure thanks for advise
How much hp does the carbon fiber spoiler adds ?
@JohnnyFabz
5 жыл бұрын
+5
I bet your finger hurt after spraying all them cans huh and should of purchards some pearliser for it
how much money you spend ??
@JohnnyFabz
5 жыл бұрын
It’s been a while now sense I have done it but I think it was under $100
whats the name of the music?
I still don't get why you sanded the car
@clarkeboss1072
5 жыл бұрын
SCOLLAY TABLE so that the plastic dip would bond to the metal a lot better preparation is key to producing results you should always sand before applying fresh paint
@matthewalston1226
5 жыл бұрын
@@clarkeboss1072 bullshit! I did the same thing to my Xterra 5 years ago. You DON'T have to sand anything! I painted my 07 Xterra with spray cans 5 years ago and it still looks awesome. No preparation needed except making sure the paint is clean and dry.
not trying to throw hate ...say uhhh less mate heard it like 50 times before you got the the painting timelapse
@JohnnyFabz
5 жыл бұрын
I know I need to work on not doing that lol one of my first real videos so was really new to the camera thing
Gonna be a basterd to get off m8 needs more coats
@JohnnyFabz
6 жыл бұрын
Daniel Lee kinda figure it would be a pain but oh well!
@carlosavina374
6 жыл бұрын
They sell a spray that is a chemical & you coat the car with it and the plasti dip dissolves all you need to do it wash it with water and comes right off
@PuR3MaGzz
6 жыл бұрын
Whats it called
@PuR3MaGzz
6 жыл бұрын
I need that so i can take off the plastic dip they did on my hatch that i got
@RandySoWavvy
4 жыл бұрын
Alexxrendonn it’s called Plasti Dip dissolver
This shit tuned yet?
@JohnnyFabz
4 жыл бұрын
Yup!!!! Dyno vid soon so stay tuned for it
MF THIS SHYT LOOKS GREAT I WOULD DO MY TAHOE BUT ITS TOO BIG
Très belle moi je suis un peintre aussi
@JohnnyFabz
3 жыл бұрын
Check out the newest videos where I actually painted the car.
My 2013 Dodge Charger about to look 🔥😁
@DrPigment
4 жыл бұрын
Delvon Bailey there is a much better way. Less expensive too. Promise this isn’t a spam thing. Send us a message.
Why didnt you clean the car first it wont bond right otherwise
@JohnnyFabz
5 жыл бұрын
Glen Cain been on for over year haven’t had a problem with anything coming off.
@bangalgar
5 жыл бұрын
@@JohnnyFabz that's the problem tho when you do go to take it off you're gonna fight it the whole way cause ya didnt clean it.
@matthewalston1226
5 жыл бұрын
@@bangalgar you have no clue what you are talking about!
Don’t quit your day job
Not bad Ging
That shitbox looks much better in gray. Mucho bettero.
@JohnnyFabz
6 жыл бұрын
Mjolnir Stormbreaker thanks lol
@estebanacosta6522
6 жыл бұрын
Mjolnir Stormbreaker what in the fuck is bettero? U literally just said nothing really
@renaldobryan1047
5 жыл бұрын
@ lolol. I agree
Your fingers must have been killing you
That uh "music" uh is um awful. Wasn't a bad dip job for just using cans.
@JohnnyFabz
5 жыл бұрын
Thanks man I know I need to work on not saying uh lol
dude who the hell doesn't mask the windows and also doesn't wear a mask?
@JohnnyFabz
5 жыл бұрын
Stuff rubs right off with ease don’t need to mask the windows waste of material for real paint jobs we do
Hahaha when you peeled off that tape hahahah on the edges around the windows .. hahahahah I'm almost taking a shit because lol.... Hahahah totally entry level show!!!
@JohnnyFabz
4 жыл бұрын
You are right this was my very first time ever using plastidip
@choopiebmw
4 жыл бұрын
@@JohnnyFabz for a first time job I think you did great!👍👍😁
good job but i dont like plasti dip for the fact that if you dont use their glossifier and leave it matte then all the dirt and places where you touch stay there
@bangalgar
5 жыл бұрын
Wrong
I think your ok but hate the car, u can't paint a terd and make it look nice, but maybe if u painted the terd yellow, it would look like a cob of corn, and so I think I different colour choice, something zesty and vibrant
@JohnnyFabz
5 жыл бұрын
ben king thanks man
@bangalgar
5 жыл бұрын
Honda is king gtfo
Damn bro thats terrible. NEVER use cans for a full car. I bet that is gonna be a bitch to peel…have to use a turbine sprayer system
Your next video will be from the after life if you don't use a mask!!!!!!!!!!
@JohnnyFabz
4 жыл бұрын
Lol