Wonderful explanation. Reading all the dimensions in ASME B16.20 was very difficult to visualize. You have made it much simpler. Moreover, thank you for dismantling the SPW gasket. Helped to better understand it's construction.
@diptamallick1382 Жыл бұрын
Beautiful presentation. All your videos are of immense use to any piping engineer.
@topeodumboni6927 Жыл бұрын
Thank you, sir, for educating us. A word of appreciation from Nigeria
@hashmat29036 ай бұрын
Very informative...thanks
@sankarghosh1485 Жыл бұрын
Very informative. Your intent for sharing knowledge is really praiseworthy.
@sajadbarzegari6199 ай бұрын
it was the best education. thank you
@sen-ow7ub Жыл бұрын
Amazing.You have explained this video very well with clear explanations which I have never seen before in any site. please make more videos about gasket. Some time purchased spiral wound gasket without inner ring. But the connect line is requirements of FBE inner coatings In cases if we are using gasket without inner ring . The fluid service exposed to flange. I hope there are two solution either flange surface should be FBE or should be purchased spiral gasket with inner ring. However we need your advice about this issue.
@sen-ow7ub Жыл бұрын
I request you on behalf of all your subscribers to please post more videos.
@aghilmoghbeli7626 Жыл бұрын
Thanks for this nice video please provide videos about flat and RTJ gaskets.
@anishwasrajan5 Жыл бұрын
Videos are very good ,more informative about ping thank you
@sen-ow7ub Жыл бұрын
Amazing
@Sam-81_98 Жыл бұрын
Very Informative. Many thanks.
@azeemvizag Жыл бұрын
Very precise explanation ....Thank you very much sir
@pratikz1274 Жыл бұрын
Thank you sir..!! Wonderful explanation.
@kunameeralmariappan4626 Жыл бұрын
Good
@sen-ow7ub Жыл бұрын
Please explain flange isolation kit in next video if possible. Thanks sir
@sen-ow7ub Жыл бұрын
fusion bonded epoxy coating for piping( FBE)
@sen-ow7ub Жыл бұрын
Please mention in your next video that no inner ring is required up to what sizes. Thanks for your information.
@BalakumaranJ
6 ай бұрын
As per ASME B16.20, Inner rings are required for the below conditions: i) When PTFE is used as a filler material ii) Based on size and rating combinations (in general above 600#) iii) Recommended for Vacuum service
@vikrambar Жыл бұрын
hello Sir can we use spiral would gasket in flat face flanges as well?
@gourisankarsamanta7670
Жыл бұрын
No, we should not use, because while tightening flange bolts, moment will be generated in flat face flange and it may crack because in most of the cases flat face flanges are of cast iron which is brittle.
@vikrambar
Жыл бұрын
@@gourisankarsamanta7670 thanks for your reply!! My flange is gun metal flat face Which is not brittle. I believe crack will not occur in gun metal flange however off course bending moment will be there. So I am in confusion whether should I use this gasket or not in flat face. I read somewhere on internet that we can use it in both flat face as well as in raised faces flanges. Please suggest your opinion.
@gourisankarsamanta7670
Жыл бұрын
@@vikrambar Gun metal is soft and malleable having mainly Copper and Tin. Spiral wound gasket can be used for gun metal flat face flange.
@vikrambar
Жыл бұрын
@@gourisankarsamanta7670 appreciating your prompt reply, thanks!!
Пікірлер: 24
Wonderful explanation. Reading all the dimensions in ASME B16.20 was very difficult to visualize. You have made it much simpler. Moreover, thank you for dismantling the SPW gasket. Helped to better understand it's construction.
Beautiful presentation. All your videos are of immense use to any piping engineer.
Thank you, sir, for educating us. A word of appreciation from Nigeria
Very informative...thanks
Very informative. Your intent for sharing knowledge is really praiseworthy.
it was the best education. thank you
Amazing.You have explained this video very well with clear explanations which I have never seen before in any site. please make more videos about gasket. Some time purchased spiral wound gasket without inner ring. But the connect line is requirements of FBE inner coatings In cases if we are using gasket without inner ring . The fluid service exposed to flange. I hope there are two solution either flange surface should be FBE or should be purchased spiral gasket with inner ring. However we need your advice about this issue.
I request you on behalf of all your subscribers to please post more videos.
Thanks for this nice video please provide videos about flat and RTJ gaskets.
Videos are very good ,more informative about ping thank you
Amazing
Very Informative. Many thanks.
Very precise explanation ....Thank you very much sir
Thank you sir..!! Wonderful explanation.
Good
Please explain flange isolation kit in next video if possible. Thanks sir
fusion bonded epoxy coating for piping( FBE)
Please mention in your next video that no inner ring is required up to what sizes. Thanks for your information.
@BalakumaranJ
6 ай бұрын
As per ASME B16.20, Inner rings are required for the below conditions: i) When PTFE is used as a filler material ii) Based on size and rating combinations (in general above 600#) iii) Recommended for Vacuum service
hello Sir can we use spiral would gasket in flat face flanges as well?
@gourisankarsamanta7670
Жыл бұрын
No, we should not use, because while tightening flange bolts, moment will be generated in flat face flange and it may crack because in most of the cases flat face flanges are of cast iron which is brittle.
@vikrambar
Жыл бұрын
@@gourisankarsamanta7670 thanks for your reply!! My flange is gun metal flat face Which is not brittle. I believe crack will not occur in gun metal flange however off course bending moment will be there. So I am in confusion whether should I use this gasket or not in flat face. I read somewhere on internet that we can use it in both flat face as well as in raised faces flanges. Please suggest your opinion.
@gourisankarsamanta7670
Жыл бұрын
@@vikrambar Gun metal is soft and malleable having mainly Copper and Tin. Spiral wound gasket can be used for gun metal flat face flange.
@vikrambar
Жыл бұрын
@@gourisankarsamanta7670 appreciating your prompt reply, thanks!!