Piping Double Rolling calculation | Updated
This video explain How to calculate Piping rolling calculation (Vertical rolling and Horizontal Rolling) by using Pythagoras Theorem
Newly Updated exercise..Watch,Share and comment....
#pipingformula #technicalpiping #pipingrolling
Watch More Piping videos...
1.Layout and Development of Pipe Branch 90 degree : • Layout and Development...
2.Piping_How to read isometric drawings_Basic : • Piping_How to read iso...
3.Pipe wall thickness calculation as per ASME B31.3 : • Pipe wall thickness ca...
4.Piping_Fabricate 45 Degree Elbow(miter bend) from pipe : • Piping_Fabricate 45 De...
5.How to fit up pipe to 45 deg elbow? : • How to fit up pipe to ...
6.How to fit up pipe to flange? : • Piping symbols In isom...
Пікірлер: 89
Now your calculation is everything okk. Excellent 👍👍👍👍.
Best tutor about rolling pipe ,thank u very much sir
Best ever explanation.thanks much
Really this is great knowledge about rolling
Sir, thank you for understanding the difficulty of the new learner and simplified the complex concept very easily. Thank you so much . I am waiting for another new video
V...nice information Sr. .
Thanks, very useful 🌷🙏
Best explanation of piping degrees
Very very useful brother..thank you
I like this video. I watched it more than a half a dozen times. IT CONTAINS MANY GOOD POINTS!!! You accurately demonstrate 3 of the 6 trigonometric functions. All of your math is correct for any 2 dimensional triangle. The problem which I see in this video is that 2 dimensional trigonometry does not accurately explain trigonometry in 3 dimensions. Compound rolling angles must be computed anytime that you are working in 3 dimensions. Even though this appears to be a 2 dimensional problem, as soon as the 3rd dimension is included (the roll) all bends now become compound bends. 1 bend is now doing what 2 bends would normally do in 2 separate planes. For anyone to easily visualize your diagram, get yourself a rectangular box. A rectangular box of facial tissues will work. Place your tissue box on a table in front of you, with the flattest side down, and the 2nd flattest side facing you. Label your 3 dimensions onto that tissue box. The 800 will be written along the width of the front. The 214 will be written along the depth of the box. The 73 will be written onto the height of the box. 3 DIMENSIONS! Now poke two pencils into the box, at the points where your 3" pipe would enter and leave the box. For simplicity of understanding, rotate your box so that it matches Figure 22 on page 65 in the book: Tube Bending Simplified (available from Amazon.com or E-bay.com). Now follow the crystal clear explanation in the chapter COMPOUND LENGTH AND BEND on pages 65 through 69 in the book Tube Bending Simplified. After doing the easy to follow calculations, you will find that both of the fittings on the 831 mm center to center piece are 75.5 degree fittings. A 3" standard 90 degree elbow has a 4-1/2" radius. If you turn to page 13 in the book Tube Bending Simplified, under the 4-1/2" radius chart, you will see that a 75 degree bend has a face to center measurement of 3-7/16". Pretend that these are 75 degree bends, instead of 75.5 degree bends. Your 831 mm travel - (3-7/16 + 3-7/16) will equal 831 - 6-7/8 to equal an end to end pup piece of 824-1/8 mm.
@patricefontaine5948
Жыл бұрын
Hi, thank you for this explanation. I found an angle of ~15.7° (√ 214^2+73^2 = 226, then atan (226/800) = 15.7°). I found other videos where they take the value of the angle, 15,7 ° in this case, as base angle to determine the face to center measurement (0.6'' with 15°, instead of 3-7/16 for 75°). Could you please explain ?
@jamescosta1174
11 ай бұрын
Got it Todd! TY
Good Information Sir
Thank you 🙏
Good knowledge full video.
You videos are great , i couldn't see the pipe marking video
Very useful
Good information
Thank u brother ❤️
Thanks brother🙏❤❤ very useful 🌹🌹
Plz make video on how to find travel length for double rolling in feild measurment
So very important and thank you so much
@TECHNICALPIPING
3 жыл бұрын
You are most welcome
Thank you for
@TECHNICALPIPING
2 жыл бұрын
Welcome
Thank you very much
👌👌👍👍
hola amigo doy reciente en este rubro ayúdeme haga un vídeo en español sobre el mismo tema, esta muy interesante . muchas gracias
👍👍
please upload more sample rolling. thankyou
Nice
Amazing
@TECHNICALPIPING
Жыл бұрын
Thanks
Super
7:49 da li postoji mogucnost da bude prevedeno na srpski jezik.Video je izuzetno dobar i veoma detaljan
sir one doubt how did you get 88.9mm outder diameter from 3 inch pipe please reply me
@lukeheilbronn3631
3 жыл бұрын
3'' NB PIPE IS 88.9OD THIS IS THE STANDARD SIZE. YOU CAN PUT A BSPP THREAD ON THE END OF THIS PIPES,THATS THE REASON FOR IT.
Buen video pasar español
@TECHNICALPIPING
5 жыл бұрын
intentaré
Sir plz explain me I have one doubt ? You calculated 11.5 mm from the values of 800,214 and it's using flange side... At the same time you calculated 5degree also have to use flange side .... How its use 85 degree flange side ??
Any job is available in this field... I am a good layout engg
Sir degree agar deffrent ho to double rolling Ka travel kaise find out karenge please
It's ok
How is it finded 3 inch pipe od as 89?????
@TECHNICALPIPING
2 жыл бұрын
Its as per ASTM pipe standards dimensions...
How about 4" rolling 45°? What is the formula?
Suoer
Easier: hypotinuse = √ 800² + 214² + 73² , then find angle between adjacent and hypotenuse with formula αº = tanˉ¹ ( 73 / √ 800²+ 214²)= 5.04º or between opposite and hypotinuse by Βº= tanˉ¹ ( √ 800²+ 214² / 73) = 84.96º and rotation of flange like shown in video.
@jamshedali9229
2 жыл бұрын
your formula is nice that is so easy
@gilnicolas6377
Жыл бұрын
short formula good to use when talking about production..i have also my own formula short formula also thanks for onather formula you shown..
@Mattoilers97
Жыл бұрын
How’d you get those symbols mate
Bro now it's CRT
how you suddenly get hypothenius 831 ?
@TECHNICALPIPING
3 жыл бұрын
Its given in drawing. watch video clear.thanks. If that value not given. no issue. can find value it using any one of the formulas given here. Watch 1:37
In (1) = Horizontal rolling we shall use the Sin relationship not the Tan one.
Sir ,how to find distance 831 mm ?
@TECHNICALPIPING
3 жыл бұрын
831 given in drawing (elbow center to center distance).
@TECHNICALPIPING
3 жыл бұрын
If that value not given.no issue. can find value it using any one of the formulas given here. watch 1:37
What's mean CR on Flange CR?
Ise awaj dekar samjhaye
Tan =add/hyp
@TECHNICALPIPING
4 жыл бұрын
No,Tan = opp/adj
Bina rolling dikhaye kisi isometric drawing pe ek video banao bhai Hame kaise smjh me aayega ki rolling kaha h Ye question aaj mujhse Oman ke liye diye gaye interview me puchha gya tha Plz reply
@TECHNICALPIPING
2 жыл бұрын
ok
Здравствуйте Хороший видео но непонятно что вы говорите сделать русский перевод пожалуйста Спасибо заранее
@TECHNICALPIPING
4 жыл бұрын
спасибо, в следующий раз я сделаю лучшее видео.
@user-dc4mp9ld5k
4 жыл бұрын
@@TECHNICALPIPING Спасибо за понимание
You mentioned in the formula wrong in the tan : opp/adj,
@TECHNICALPIPING
2 жыл бұрын
Yes,But its edited correctly.watch one more time....thank u...
831 hw it came in vertical rolling
@TECHNICALPIPING
3 жыл бұрын
Its given in drawing. If that value not given.no issue. can find value it using any one of the formulas given here. watch 1:37
π×D/360 ???????
@hindudevotional1424
5 жыл бұрын
Circumference divided by 360 ...... U will get one degree value...
@alzaramechanicalconstructi9961
5 жыл бұрын
3.14×89=279.5 cf divided full degree, 279.4÷360=0.77 it's value 1 degree
@samirst3794
5 жыл бұрын
شكرا لك
@er.mdimranalam3115
5 жыл бұрын
With this formula... Convert degree into mm
関数電卓使ったら🎵(笑)❕🤣
@TECHNICALPIPING
5 жыл бұрын
はい
@hiromukayama3922
5 жыл бұрын
@@TECHNICALPIPING 余計な事言ってゴメンね🎵多分同業者だと思います。これからもお互い頑張りましょう😀👍
@TECHNICALPIPING
5 жыл бұрын
音楽について言うのですか?
@hiromukayama3922
5 жыл бұрын
@@TECHNICALPIPING sorry. I don't understand.
@TECHNICALPIPING
5 жыл бұрын
hi kayama,What you do not understand is this video.
Video no celerate
Bol ke samjao koi Hana thori h Jo aap music Dali ho keya .....
How u sloved or do calculations without speaking.. If u can't speak then I no need to make vedio
@TECHNICALPIPING
3 жыл бұрын
watch this video for to know more details about pipe rolling kzread.info/dash/bejne/Y41-ppKQZ5vVkdo.html
По русски можно
노래틀고 혼자 공부하노? 설명도 없이?
Nice