FOLLOW ME ON INSTAGRAM! @thecraig909 @carrnagge - SEND ME STUFF! (If you want) TheCraig909 P.O. Box 362 Ramona, Ca 92065 - Music by Carbon Citizen
Жүктеу.....
Пікірлер: 235
@wyohotrods3 жыл бұрын
The grill in the bed of that pickup was from a 60s dodge.
@albertgaspar627
3 жыл бұрын
just about to post that...
@davidhenson3372
2 жыл бұрын
66 dodge
@franciscomonroy4084
10 ай бұрын
@@albertgaspar627😮
@young119843 жыл бұрын
I would have had to grab that old grill shell for wall art if nothing else
@GreenDragonPainting3 жыл бұрын
Man this made me want to throw my sandwich on the floor and head to the junkyard 🤣
@prestonwillingham49763 жыл бұрын
Why didn't you just cut the valve stem tire looked good enough
@mattfarahsmillionmilelexus3 жыл бұрын
Always check the 9 inch center sections in the dent sides. I have found several N cases.
@AverageApe44
3 жыл бұрын
Can you elaborate more on what you mean by this?
@brianadams429
Жыл бұрын
In the 80's a nodular case was$500.00 out of a catalog. I found alot in 70's 4x4 f150's, and early 80's trucks where ford was clearing 9" inventory off the shelf. I found them in 2 and 4 wheel drive of early 80's
@trentontaylor54473 жыл бұрын
Those beams you bent with a torch are now super fragile!!! You’re only supposed to cold bend I beams on these old fords.
@purplemonte1
3 жыл бұрын
Was going to say same thing!!
@RalphSampson...3 жыл бұрын
The junkyards around here in Georgia (Pull-a-Part) set a wheel flat then weld another wheel vertically on to it. They use this setup at four corners. It makes for great access to the vehicle. Like your yard, they don't allow jacks or cutting torches.
@WhyBeNick3 жыл бұрын
You guys might already be planning on it, but I would definitely plate those beams. They're beefy, but they do bend if you really beat on them without reinforcement.
@andystreets46603 жыл бұрын
I have been using the new edge mustang v6 t5s in my last couple of builds. The 3.8 bellhousing bolts directly to a small block. You have to use a truck flywheel, clutch, and starter but other than that it works good.
@charleswoodbury3883 жыл бұрын
Good find can't wait to see what you do with it
@braedengraham22683 жыл бұрын
I’m in high school as well and I’ve got a lifted ‘71 f100 on 35’s with a built 352, cammed up, open headers, 850 Holley carb which is being rebuilt by my girlfriend’s dad at the moment but besides that it runs great. It’s awesome to see another high schooler that wants to build something instead of waiting for mommy and daddy to find one..... Love the truck man
@tompaciga73863 жыл бұрын
Enjoy the salvage yard videos keep up the great work
@FordFanatic8653 жыл бұрын
Best part of the day is when I get the notification that Craig posted a video 🤟🏼
@physkogamer71393 жыл бұрын
18:32 I NEED THAT BUMPER. I need that front bumper for my 75. That looks like its in such good shape
@samthelegoman39903 жыл бұрын
The ground or the floor?
@wbrandes66263 жыл бұрын
Yall should get me them headers for Christmas😂 I need them for my 460
@foxhillhomestead34443 жыл бұрын
I'm a huge square body chevy guy but I love galaxy fords and really like your f100. Really enjoy your content.
@mromatic172 жыл бұрын
That is a good idea craig when i start restoring my daily driver 1994 f150 ill go and collect the vin tags off of junked ford trucks. you are right that they can’t even be restored cuz once the truck is junked they delete the vin off the record and its the only tangiable.
@pinstripingbybear.3 жыл бұрын
@6:30 thats a dodge truck grille like a 60tys power wagon grille
@spencersand27543 жыл бұрын
I want all those old ford pickups 😍
@backyardmechanicrestoratio69583 жыл бұрын
11:50 that car would be a clean drag car build ngl makes me wish i had the money and lived in the states sometimes
@ClassicGBodyGarage3 жыл бұрын
No rust anywhere! Damn you boys are lucky to live where ever you are.
@brianadams429 Жыл бұрын
If i were you i'd make sure the 9" didn't have a nodular case in it. I used to go with my dad to the you pullit yards in the 80's and 90's. Some of 70 models that were 4x4 f150 had nodular cases, and early 80's f150 where ford was clearing shelves for 8.8, i found several over the years.
@beardedscrapper5383 жыл бұрын
That truck is sick.
@chevylandt.v3 жыл бұрын
Oh dang my Friday just got better. Is that white dentside grille good looking for both iner and outer for a 73 -77 f100.
@giftdcam84723 жыл бұрын
That camaro was a world class.. I’m glad you called the guy lol
@Z3CHYD3 жыл бұрын
Man I need to get to my local big junkyard now lol
@harrisonhunter75123 жыл бұрын
Great video mate, Datsun 280zx would be a cool car for a project .
@abelvillalobos78523 жыл бұрын
D100 65-67 grill!!
@foxbodiesforever92343 жыл бұрын
The dimple bearing cup your talking about will have the word Timken on it that will tell you it is a world class
@joewiechowski66603 жыл бұрын
It’s a world class t5 has a timken front bearing that doesn’t look like a freeze plug and it has a star bit bolt in the side which means world class and depending on the side numbers it’ll tell you the gear ratio
@Snakeman19853 жыл бұрын
I collect the RPO tags off the s10's I take parts off of
@gasratzcustoms3 жыл бұрын
Good times!!!!
@alecfromminnenowhere20893 жыл бұрын
Is the roof rust caused by vehicles in close proximity to the ocean and the saline moisture? I've seen that in Florida, but Florida has a lot more humidity.
@codyreynolds63333 жыл бұрын
Buy that grill insert on the black truck and I'll buy it from u I need bolth sides if they are good and find me a ashtray lol I like original stuff
@jcfireman22152 жыл бұрын
That first rate porosity in that weld on the spring perches.
@dominicbrinas54663 жыл бұрын
I just picked apart that red and white bullnose the other week 😂
@ameliaalvarado5265
3 жыл бұрын
What pick a part is this
@dominicbrinas5466
3 жыл бұрын
@@ameliaalvarado5265 its in Chula Vista
@mromatic172 жыл бұрын
@thecraig909 were your front I beam axles bent? Is that whay you had to heat it up with a torch and bend it with a jack?
@andrewstevenson51553 жыл бұрын
yes i love the 240z and my 280z i would definitely watch videos on that. and on another note why are your junk yards so good cant find anything old in my yards its usually all new cars :(
@mathewdostal21803 жыл бұрын
Bro I have a 1970 f250 bump side and I need to add taller springs and bend my I beams. Could you hook up a Ford Brother up with the measurements for the jig you built? I’m not in California Desert racing or anything just trying to get my old shitbox taller so I can bomb it through the woods here
@fullsendsornosends11763 жыл бұрын
If i gota dotsun it would probably have a v8 in it... the rotsun mk2
@jesusfilberto33442 жыл бұрын
for How much will a standard transmission cost for a Camaro 8 cyl. Like the blue Camaro
@Robrt323 жыл бұрын
I wish we had yards like that around here. Everything pre 90’s has been hauled to the crusher.
@mikeobrien37443 жыл бұрын
Dodge truck/van grill. 1966-677 dish headlights. Popular style, don't ask me why.
@communismman14713 жыл бұрын
Are the tail lights on that studebaker horizontal or vertical
@scottm-nc94513 жыл бұрын
Not sure how I came to this video but glad I did... 😊 new sub 😊 In yard 1 was a teal green Ford escort 92 - 99. ... how can I contact this yard I have my mom's 95 Mercury Tracer ( escort same thing) ..looking for hard to find parts. ...
@pattreadwell61493 жыл бұрын
Lucky day for sure wow
@AncientAir10 ай бұрын
My favorite place to scrap for rarity’s… PYP West. Used to be named LKQ.
@keithjanikula49143 жыл бұрын
Isn't there a difference between gas and diesel turbos? I didn't think they were interchangeable.
@cameronmagnino58193 жыл бұрын
What Junkyards did you go to cause I need parts for my 97 Dodge Ram 1500 and 94 F-150
@huevigarage3 жыл бұрын
Datsun with a vh45 Infiniti engine and a z32 trans. Sounds like a fun car. Or a inline 6 turbo. Get one
@owenacker49503 жыл бұрын
Those headlight rings from the A100 Dodge van grille will sell same day for $60+ on ebay
@taylorward42053 жыл бұрын
Got that same KING hat 👌
@texjake33 жыл бұрын
Dude, I need those headers off that blue Camaro. I need them for my Vortec heads. I'll pay you to shipped to me in Texas!
@jeromewieland55
Жыл бұрын
Shorty headers make about 2hp over a set of manifolds. I’d find a good set of long tubes because it’s not worth the money or time to do a set of shorties on anything.
@gymbob793 жыл бұрын
I don’t feel alone anymore!! My Dana 60 is 16 spline too 👎🏻 ‘76 f250
@centraltexasfoxbodies3 жыл бұрын
What's the casting number on the t5? Ford started using the world class t5 in 1985 so if it has an e5 part number than it's a world class, the 4 cylinder t5 work behind the v8 with a different pilot bearing, people have good luck running the 4 cylinder t5 behind v8...
@trevordevins10423 жыл бұрын
Get that 460!!!!
@dk8320023 жыл бұрын
It's because the gm t5 doesn't have a spot for a trans mount because the body uses the torque arm
@dumbird7893 жыл бұрын
Just went and picked up some parts for my maro
@leewinter62673 жыл бұрын
The headers, Those are part of the Banks Powersport system!!
@danielheartsill42693 жыл бұрын
I wouldn't put money on it either but the grill looks like a Dodge van from the sixties. It didn't stay in the camera for long and didn't get to see the whole thing, but my guess is Dodge.
@recon5320023 жыл бұрын
Love those California bone yards
@keepitsolidkeepitreal28773 жыл бұрын
Thecraig909 Hey I’m in Cali BayArea visit Pick N Pull which one do you guys go to what state what county being looking for Ford Bronco’s Ford Mustangs
@shawnburton68393 жыл бұрын
What junk yard is that. I need that d100 grill
@jcnpresser Жыл бұрын
If you can put a5/8 sockets over the input shaft, it’s not a world class. The pilot is a bit bigger on a world class.
@redrooster70163 жыл бұрын
How much was the t5 from the junkyard??
@thisyoutubechannel310711 ай бұрын
Craig I'm willing to bet that dually had a banks power pack or something like that.
@talesofanasphaltjockey3 жыл бұрын
240/260 Z's are da bomb ... DO IT !!!!
@timedwards82253 жыл бұрын
I like that body style of the Datsun
@devonnile79783 жыл бұрын
i have a 70 f100 and i need new grill inserts and all i can find is 69s and 71-72s
@Justin_Newman3 жыл бұрын
That’s the one in Chula Vista huh? Every time I call the yay that got f250s in but they don’t. If y’all know a place that has f250s in the San Diego area please let me know😂
@farmerjordan19 Жыл бұрын
Okay if your looking for a world class t5 the only car I know of that came with it is the svo and fun fact it's a 4 cylinder everything else came stock with a regular t5
@tommyhall3503 жыл бұрын
If you get a chance to look up maple motors Henderson bill TN look at the 64 ford white it is for sale go to u tube check it. Out you will like it very nice
@jeremyrios4333 жыл бұрын
Dude what's up with the holes in those welds? Try running less stick out on the wire like 3/16 😁
@TaylorBickett3 жыл бұрын
0:20 seconds i hear that Point North song going ;)
@kennethporst4359 Жыл бұрын
We need more people saving these GEMS uuuhhh🤕🥺
@lucusc40023 жыл бұрын
I wish junkyards were like this in Canada or at least in my area we do not have the abundance of parts and cars you guys have.
@charleschidester67673 жыл бұрын
The grill is from a dodge D100 66 through 70
@abelvillalobos7852
3 жыл бұрын
Mid 65-67 grill
@shawnburton6839
3 жыл бұрын
I need that
@DawsonDodgeW1503 жыл бұрын
Bro I would really like those door off that 79 dodge but I live in Georgia
@mikephister39403 жыл бұрын
where was the second yard you saw the ramcharger
@redneckasmr-xd1gg3 жыл бұрын
i drive a obs f150 got the inline 300 and 5 speed. i want to convert it to 4x4, i need to find a doner some time like that bronco but i need a gearbox i cant stand auto.
@brianadams429
Жыл бұрын
You could find a np205 divorced (independant) transfercase as long as you have enough wheelbase.
@j-port88183 жыл бұрын
Hope you grabbed the drain plug for that t5. It was literally laying on the ground next to it.
@Thecraig909
3 жыл бұрын
I did
@AndrewHCann3 жыл бұрын
Excellent video
@Scrapy-ih7ob3 жыл бұрын
I need set front coil springs for my Bronco ...79 can you grab me set/ send me price. every time try get from Auto parts sold out....
@timothyperreault33303 жыл бұрын
Maybe you could have him bend your front axle to correct the camber
@LKRS1113 жыл бұрын
Thermoquad is a Mopar carb & Quadrajet is Gm .
@dk8320023 жыл бұрын
My buddy is building a fiero with an awd wrx sti drivetrain
@michaelclark49823 жыл бұрын
The grill is out of a 66 to 67 dodge pickup its called a pie plate.
@ryanhallahan28173 жыл бұрын
The grille is an early 60s dodge d100
@JusstLynnn3 жыл бұрын
What camera do you use?
@joshuahartford93293 жыл бұрын
The grille was from a dodge sweptline pickup
@FD_FTP3 жыл бұрын
Me wanting to collect vins after watching this lol
@carsonpeterson7203 жыл бұрын
I want those longtube headers
@joey6119 Жыл бұрын
That truck is begging for a stroker 351 Windsor 408 or 427 sweet maybe 396 or 8 I don't remember
@jesseduke6943 жыл бұрын
Bad move cutting the side wall of them tires. Were they a set of 4? Even if not they were a set of 2. Not sure about in California but were im at that was a usable tire for a few miles anyway. I have brand new set of mud tires for my truck I use only to go to the mud runs. The other 11 months of the yr I buy cheap used tires like those & there good enuf to burn up showing off by smoking your tires for your buddys or flying up & down the gravel roads all over the county just out being a terror. Its alot cheaper than buying new mud tires every yr. You could have cut the valve stem.
@mv31293 жыл бұрын
Would be nice if you tell your subscribers which wrecking yards you guys go to.
@shawnburton68393 жыл бұрын
What junk yard is that. Need that grill
@wolfeyford84493 жыл бұрын
Haven't seen you do a burnout yet this year guys
3 жыл бұрын
17:03 Hope you can buy and save that Datsun 280Z.
@jaga69013 жыл бұрын
where is that junkyard located because i need some parts for a ford thunderbird 1979
Пікірлер: 235
The grill in the bed of that pickup was from a 60s dodge.
@albertgaspar627
3 жыл бұрын
just about to post that...
@davidhenson3372
2 жыл бұрын
66 dodge
@franciscomonroy4084
10 ай бұрын
@@albertgaspar627😮
I would have had to grab that old grill shell for wall art if nothing else
Man this made me want to throw my sandwich on the floor and head to the junkyard 🤣
Why didn't you just cut the valve stem tire looked good enough
Always check the 9 inch center sections in the dent sides. I have found several N cases.
@AverageApe44
3 жыл бұрын
Can you elaborate more on what you mean by this?
@brianadams429
Жыл бұрын
In the 80's a nodular case was$500.00 out of a catalog. I found alot in 70's 4x4 f150's, and early 80's trucks where ford was clearing 9" inventory off the shelf. I found them in 2 and 4 wheel drive of early 80's
Those beams you bent with a torch are now super fragile!!! You’re only supposed to cold bend I beams on these old fords.
@purplemonte1
3 жыл бұрын
Was going to say same thing!!
The junkyards around here in Georgia (Pull-a-Part) set a wheel flat then weld another wheel vertically on to it. They use this setup at four corners. It makes for great access to the vehicle. Like your yard, they don't allow jacks or cutting torches.
You guys might already be planning on it, but I would definitely plate those beams. They're beefy, but they do bend if you really beat on them without reinforcement.
I have been using the new edge mustang v6 t5s in my last couple of builds. The 3.8 bellhousing bolts directly to a small block. You have to use a truck flywheel, clutch, and starter but other than that it works good.
Good find can't wait to see what you do with it
I’m in high school as well and I’ve got a lifted ‘71 f100 on 35’s with a built 352, cammed up, open headers, 850 Holley carb which is being rebuilt by my girlfriend’s dad at the moment but besides that it runs great. It’s awesome to see another high schooler that wants to build something instead of waiting for mommy and daddy to find one..... Love the truck man
Enjoy the salvage yard videos keep up the great work
Best part of the day is when I get the notification that Craig posted a video 🤟🏼
18:32 I NEED THAT BUMPER. I need that front bumper for my 75. That looks like its in such good shape
The ground or the floor?
Yall should get me them headers for Christmas😂 I need them for my 460
I'm a huge square body chevy guy but I love galaxy fords and really like your f100. Really enjoy your content.
That is a good idea craig when i start restoring my daily driver 1994 f150 ill go and collect the vin tags off of junked ford trucks. you are right that they can’t even be restored cuz once the truck is junked they delete the vin off the record and its the only tangiable.
@6:30 thats a dodge truck grille like a 60tys power wagon grille
I want all those old ford pickups 😍
11:50 that car would be a clean drag car build ngl makes me wish i had the money and lived in the states sometimes
No rust anywhere! Damn you boys are lucky to live where ever you are.
If i were you i'd make sure the 9" didn't have a nodular case in it. I used to go with my dad to the you pullit yards in the 80's and 90's. Some of 70 models that were 4x4 f150 had nodular cases, and early 80's f150 where ford was clearing shelves for 8.8, i found several over the years.
That truck is sick.
Oh dang my Friday just got better. Is that white dentside grille good looking for both iner and outer for a 73 -77 f100.
That camaro was a world class.. I’m glad you called the guy lol
Man I need to get to my local big junkyard now lol
Great video mate, Datsun 280zx would be a cool car for a project .
D100 65-67 grill!!
The dimple bearing cup your talking about will have the word Timken on it that will tell you it is a world class
It’s a world class t5 has a timken front bearing that doesn’t look like a freeze plug and it has a star bit bolt in the side which means world class and depending on the side numbers it’ll tell you the gear ratio
I collect the RPO tags off the s10's I take parts off of
Good times!!!!
Is the roof rust caused by vehicles in close proximity to the ocean and the saline moisture? I've seen that in Florida, but Florida has a lot more humidity.
Buy that grill insert on the black truck and I'll buy it from u I need bolth sides if they are good and find me a ashtray lol I like original stuff
That first rate porosity in that weld on the spring perches.
I just picked apart that red and white bullnose the other week 😂
@ameliaalvarado5265
3 жыл бұрын
What pick a part is this
@dominicbrinas5466
3 жыл бұрын
@@ameliaalvarado5265 its in Chula Vista
@thecraig909 were your front I beam axles bent? Is that whay you had to heat it up with a torch and bend it with a jack?
yes i love the 240z and my 280z i would definitely watch videos on that. and on another note why are your junk yards so good cant find anything old in my yards its usually all new cars :(
Bro I have a 1970 f250 bump side and I need to add taller springs and bend my I beams. Could you hook up a Ford Brother up with the measurements for the jig you built? I’m not in California Desert racing or anything just trying to get my old shitbox taller so I can bomb it through the woods here
If i gota dotsun it would probably have a v8 in it... the rotsun mk2
for How much will a standard transmission cost for a Camaro 8 cyl. Like the blue Camaro
I wish we had yards like that around here. Everything pre 90’s has been hauled to the crusher.
Dodge truck/van grill. 1966-677 dish headlights. Popular style, don't ask me why.
Are the tail lights on that studebaker horizontal or vertical
Not sure how I came to this video but glad I did... 😊 new sub 😊 In yard 1 was a teal green Ford escort 92 - 99. ... how can I contact this yard I have my mom's 95 Mercury Tracer ( escort same thing) ..looking for hard to find parts. ...
Lucky day for sure wow
My favorite place to scrap for rarity’s… PYP West. Used to be named LKQ.
Isn't there a difference between gas and diesel turbos? I didn't think they were interchangeable.
What Junkyards did you go to cause I need parts for my 97 Dodge Ram 1500 and 94 F-150
Datsun with a vh45 Infiniti engine and a z32 trans. Sounds like a fun car. Or a inline 6 turbo. Get one
Those headlight rings from the A100 Dodge van grille will sell same day for $60+ on ebay
Got that same KING hat 👌
Dude, I need those headers off that blue Camaro. I need them for my Vortec heads. I'll pay you to shipped to me in Texas!
@jeromewieland55
Жыл бұрын
Shorty headers make about 2hp over a set of manifolds. I’d find a good set of long tubes because it’s not worth the money or time to do a set of shorties on anything.
I don’t feel alone anymore!! My Dana 60 is 16 spline too 👎🏻 ‘76 f250
What's the casting number on the t5? Ford started using the world class t5 in 1985 so if it has an e5 part number than it's a world class, the 4 cylinder t5 work behind the v8 with a different pilot bearing, people have good luck running the 4 cylinder t5 behind v8...
Get that 460!!!!
It's because the gm t5 doesn't have a spot for a trans mount because the body uses the torque arm
Just went and picked up some parts for my maro
The headers, Those are part of the Banks Powersport system!!
I wouldn't put money on it either but the grill looks like a Dodge van from the sixties. It didn't stay in the camera for long and didn't get to see the whole thing, but my guess is Dodge.
Love those California bone yards
Thecraig909 Hey I’m in Cali BayArea visit Pick N Pull which one do you guys go to what state what county being looking for Ford Bronco’s Ford Mustangs
What junk yard is that. I need that d100 grill
If you can put a5/8 sockets over the input shaft, it’s not a world class. The pilot is a bit bigger on a world class.
How much was the t5 from the junkyard??
Craig I'm willing to bet that dually had a banks power pack or something like that.
240/260 Z's are da bomb ... DO IT !!!!
I like that body style of the Datsun
i have a 70 f100 and i need new grill inserts and all i can find is 69s and 71-72s
That’s the one in Chula Vista huh? Every time I call the yay that got f250s in but they don’t. If y’all know a place that has f250s in the San Diego area please let me know😂
Okay if your looking for a world class t5 the only car I know of that came with it is the svo and fun fact it's a 4 cylinder everything else came stock with a regular t5
If you get a chance to look up maple motors Henderson bill TN look at the 64 ford white it is for sale go to u tube check it. Out you will like it very nice
Dude what's up with the holes in those welds? Try running less stick out on the wire like 3/16 😁
0:20 seconds i hear that Point North song going ;)
We need more people saving these GEMS uuuhhh🤕🥺
I wish junkyards were like this in Canada or at least in my area we do not have the abundance of parts and cars you guys have.
The grill is from a dodge D100 66 through 70
@abelvillalobos7852
3 жыл бұрын
Mid 65-67 grill
@shawnburton6839
3 жыл бұрын
I need that
Bro I would really like those door off that 79 dodge but I live in Georgia
where was the second yard you saw the ramcharger
i drive a obs f150 got the inline 300 and 5 speed. i want to convert it to 4x4, i need to find a doner some time like that bronco but i need a gearbox i cant stand auto.
@brianadams429
Жыл бұрын
You could find a np205 divorced (independant) transfercase as long as you have enough wheelbase.
Hope you grabbed the drain plug for that t5. It was literally laying on the ground next to it.
@Thecraig909
3 жыл бұрын
I did
Excellent video
I need set front coil springs for my Bronco ...79 can you grab me set/ send me price. every time try get from Auto parts sold out....
Maybe you could have him bend your front axle to correct the camber
Thermoquad is a Mopar carb & Quadrajet is Gm .
My buddy is building a fiero with an awd wrx sti drivetrain
The grill is out of a 66 to 67 dodge pickup its called a pie plate.
The grille is an early 60s dodge d100
What camera do you use?
The grille was from a dodge sweptline pickup
Me wanting to collect vins after watching this lol
I want those longtube headers
That truck is begging for a stroker 351 Windsor 408 or 427 sweet maybe 396 or 8 I don't remember
Bad move cutting the side wall of them tires. Were they a set of 4? Even if not they were a set of 2. Not sure about in California but were im at that was a usable tire for a few miles anyway. I have brand new set of mud tires for my truck I use only to go to the mud runs. The other 11 months of the yr I buy cheap used tires like those & there good enuf to burn up showing off by smoking your tires for your buddys or flying up & down the gravel roads all over the county just out being a terror. Its alot cheaper than buying new mud tires every yr. You could have cut the valve stem.
Would be nice if you tell your subscribers which wrecking yards you guys go to.
What junk yard is that. Need that grill
Haven't seen you do a burnout yet this year guys
17:03 Hope you can buy and save that Datsun 280Z.
where is that junkyard located because i need some parts for a ford thunderbird 1979
@Thecraig909
3 жыл бұрын
Chula Vista LKQ pick your part