Peugeot 307 Not Starting / BSM fault / Read description !!

Автокөліктер мен көлік құралдары

Hi there , in this video we have a patient peugeot 307 1,4 gassoline from PSA group who decided to implement the main relay in one piece of hardware, so the relay it's not removable ...so they say, in reality you can resolder or replace the relay with a little patience. In the video example i decided to only resolder the dry joints. First thing that you have to check it's the 12v supply from ignition coil, if the 12v it's not there, you can bypass directly 12v to the ignition coil and start the car, do it on your own risk. The problem can occur also when the engine it;s at working temperature and you can experience random engine stops or stall. This is as usual , a quick tip to guide you in the right direction, the rest is up to you ! Don't be shy and give a thumbs up and subcribe if this helps you !! Thank you ! A more in depth approach on a citroen c4 you will find it here ‪@LMAutoRepairs‬
Music is created in Fl studio , this is my soundcloud page
/ amp-pug

Пікірлер: 36

  • @LMAutoRepairs
    @LMAutoRepairs3 жыл бұрын

    Nicely done! 👍👍👍

  • @amperugarage

    @amperugarage

    3 жыл бұрын

    Thank you 🙏

  • @Bounty-Hunter69

    @Bounty-Hunter69

    Жыл бұрын

    LM Auto Repair@ This is completely unnecessary to do. You should mount an external relay, there are here on youtube which fuses you should use. This way is way too advanced...

  • @LMAutoRepairs

    @LMAutoRepairs

    Жыл бұрын

    @@Bounty-Hunter69 There is always other ways, depends how neat and professional you want to be, or, how much the owner is willing to spend... I have in the past by passed internal relays with external relays, I have videos on my channel explaining just that... 👍👍👍

  • @amperugarage

    @amperugarage

    Жыл бұрын

    @@LMAutoRepairs you are the man ! I would love to meet you .

  • @LMAutoRepairs

    @LMAutoRepairs

    Жыл бұрын

    @@amperugarage ☺️ 👍

  • @dominicbarne5218
    @dominicbarne52183 жыл бұрын

    It’s nice to see someone willing to pull one of these apart to repair rather than replace, I’ve got a shelf full of these all working fine for quick replacement but I still like to strip inspect and repair just for my own satisfaction, nice 👍🏻

  • @hjalle74

    @hjalle74

    2 жыл бұрын

    Do you possibly have a BSM-L02-00 that you could sell me? Ship to Sweden?

  • @alexe610
    @alexe6103 жыл бұрын

    Thank you very much for sharing.

  • @amperugarage

    @amperugarage

    3 жыл бұрын

    Thanks for watching !

  • @joseluisojeda3522
    @joseluisojeda35223 жыл бұрын

    muy bueno saludos desde argentina

  • @florentinamarin7140
    @florentinamarin71403 жыл бұрын

    Up up 👌👌👌

  • @fuzzs8970
    @fuzzs89702 жыл бұрын

    Thank you for sharing your work. What did you do to repair the ECU? Just reflow some dry joints? Thank you again

  • @markthompson1134
    @markthompson11343 жыл бұрын

    where do you get the soldering irons from

  • @latelierdeludixo6917
    @latelierdeludixo69173 жыл бұрын

    Awesome ! 👍

  • @amperugarage

    @amperugarage

    3 жыл бұрын

    Thank you !

  • @markthompson1134
    @markthompson1134 Жыл бұрын

    my peugeot has no power at fuel pump i think relay has gone fuses are ok where do you get the heat gun and solder iron from to do the job

  • @nighthawkflyer
    @nighthawkflyer2 жыл бұрын

    Would be better to change the Relais. The contact inside is burned. The resistance will produce heat and the solder joint breaks again.

  • @atomichawk3720
    @atomichawk37207 күн бұрын

    My dipped or dimmed headlights are not working. The main beam is working but the normal light for night driving is not working anymore. Can I switch a LO4 unit with a LO3 unit? Or which relay is for the dimmed headlights? Greetings

  • @1nfiniteloop
    @1nfiniteloop3 жыл бұрын

    Awesome video. Gives me hope that if anything else goes wrong with my Peugeot, I can try to fix it :) What did you spray on the circuit boards? WD40? Something else? Resin? and how did you seal the electronics box? Just with a heat gun? something else?

  • @amperugarage

    @amperugarage

    3 жыл бұрын

    Spray with isopropyl alcohol and clean, try to put it back with the soldering iron or glue gun, your choice

  • @arthunterns
    @arthunterns2 жыл бұрын

    I hate that BSM thing. First of all, on the heavy rain this summer, got water in engine bay. Over the battery and water got in BSM compartment. I couldn't start a car, multiple errors. Then I found a used BSM(same model and numbers). Connected and car started immediately. It was fine for about 4-5 months, untill we again had around 7 days of light and moderate rain. While driving, I would get ABS/ESP, handbrake error when braking. But, car would go normal, I thought it was ABS sensor or something. But two days later, car just shut down, on its own, and pulled handbrake. I was able to start it again, went for 500m, where while idle car again shut down. I wasn't able to start it, starter was working but I guess no fuel was coming. Then it started again, then same story. To make a story short, very dangerous that car just switch off during driving. You could get a serious injury, I lost a power steering. Anyway, in garage, they used Lexia/Dialbox and they were able to set it all again. They recalibrated gearbox, car now runs fine. But, the problem is with that BSM thing.

  • @shazreenshahrul1821

    @shazreenshahrul1821

    Жыл бұрын

    U change the bsm and problem solved ?

  • @curiousboy4245
    @curiousboy42453 жыл бұрын

    If I change the ecu kit (Bsi, Bsm, Ecu and the key system from another Rcz will I still need a programming procedure..)

  • @amperugarage

    @amperugarage

    3 жыл бұрын

    The car will start

  • @juliocesarparionavilca6071
    @juliocesarparionavilca6071 Жыл бұрын

    Thanks a lot it's a great video! I have a peugeot 307 and my problem is that the car takes some minutes o attempts to crank the engine until it wasn't it more so I diagnosticed starter, transponder, contacts on key even I decided to starting engine with by pass on starter and then the problem is alternator isn't charging the battery

  • @juliocesarparionavilca6071

    @juliocesarparionavilca6071

    Жыл бұрын

    PD: Sorry for my English grammar

  • @amperugarage

    @amperugarage

    Жыл бұрын

    It s hard for me to diagnose based on what you telling me, try check fuses.. maybe you shorted something.

  • @rammacaliphate
    @rammacaliphate3 жыл бұрын

    I got the same problem on a 307cc 2.0l, cranks but won’t start. All sensors tested fine.could it be the same problem?

  • @amperugarage

    @amperugarage

    3 жыл бұрын

    I think so, measure the 12v reference at ignition coil connector

  • @TheCyrax60
    @TheCyrax602 жыл бұрын

    My 307 doesn't power up in the morning, usually after disconnecting all cables from the fusebo and replugging after a while, it powers up but starting it will be a problem. If you then remove the starter fuse and replace, the car will start. What is the problem? Is it the fusebox or something else? This morning, all efforts to start it was non effective. The car is just sitting outside. Dead.

  • @curiousboy4245
    @curiousboy42453 жыл бұрын

    Hi hope you doing good I would like to know what is the difference between BSI AND BSM..

  • @Smok_HB
    @Smok_HB2 жыл бұрын

    😎😎😎

  • @sibbsmahachi2420
    @sibbsmahachi24202 жыл бұрын

    Where are you guys

  • @oldman1026
    @oldman10262 жыл бұрын

    Why this idiotic music concert ?

  • @amperugarage

    @amperugarage

    2 жыл бұрын

    😂😂😂😂 sorry for inconvenience . 🙏🏻

Келесі