Great video thank you

Narrow diameter PVC pipe makes a great material for creating the radius in forms.

@boatdevoted

Жыл бұрын

Thanks, that's a good suggestion, I´ll try that next time!

Great work. My only suggestion would have been to mount the bracket higher. To have the cavitation plate at the proper height on the outboard will require it to be mounted higher then the sterndrive was. A 60mph boat ypu have to go up 1" for every 12" you go back. You may have to go 2" or more up to avoid dragging the motor and reducing speed and efficiency.

@boatdevoted

Жыл бұрын

Thanks! I very much understand your concern, but the height of the bracket is very much discussed in forums for these kind of boats, so it should be ok. I also have a Seastar jackplate waiting to be mounted, so it will work out fine! 👍

@docksidemarine4273

Жыл бұрын

@@boatdevoted ok thats good! So how much higher did you have to go then the stern drive for it to all work out?

@boatdevoted

Жыл бұрын

@@docksidemarine4273 If I’m not mistaken, +75cm from lowest point of the transom. These boats tend not like being rigged to high. I never ran the boat with inboards, they were sold immediately. (See part 1)

You say you're not good with CAD... I think you did a GREAT job with CAD: Cardboard Assisted Design LOL...

Nice work

@boatdevoted

Жыл бұрын

Thanks!

I applaud you in this task, I might add you should always use gravity to help you wet out fiberglass cloth, for example, when wetting out fold your material over on itself, wet from the substaraight, fold it to the location where it will live and do the same on the other side. it appears that your trailing edge of the bracket is lower than the part that joing your boats transom ? if so this may act as a trim tab causing a Bow down attitude. Please make sure tiyr boats transon will support the trust of the motor better to address this now rather than later,, LOve the work keep at it ! all the best

@boatdevoted

Жыл бұрын

Thanks! It’s a good point (well, both points are…)! I do have my thoughts about the bracket angle, but it should be ok, If not, I just have to fix it next winter. After this project that seams as a small edit.

Nice work! Im currently doing exactly same kind of project. Smuggler 28 c2 inboard to Outboard conversion with DIY fiberglass bracket for Yamaha F350. Greetings from Finland!

@boatdevoted

Жыл бұрын

Interesting! Looking forward to see your progress and read about the numbers. When do you expect to be done?

@BCB-Boats-Media

Жыл бұрын

@@boatdevoted I try to get it on water during next summer but... Lets see 😅

Hi! Great work, currently working on a boat myself. Where did you buy the Divinycell?

@boatdevoted

Жыл бұрын

Thanks! I bought mine from Diabgroup.com here in Sweden. Good luck with your project, what is it?

@patrickaase

Жыл бұрын

@@boatdevoted currently working on a Argocat 17. May i ask how much it cost pr. square meter?😁

@boatdevoted

Жыл бұрын

@@patrickaase nice boat! Can’t recall, but it was expensive. Didn’t want any wood in the transom and coosaboard was hard to find so this was the solution.

Could you please give a overview of how many layers of fiberglass you used on different parts of the bracket. I am trying to make something similar for my boat and being completely inexperienced with fiberglass im trying to figure things out.

@boatdevoted

10 ай бұрын

Hi! I do not remember how many layers I glassed in, but it’s very important to also use the right fiberglass biaxial cloth and also how you overlap the different sheets to build strength. I most likely used more layers than needed, but better to be save than sorry. Also, if you’re from US, you have coosa board on you local market that works equally well as core material. Good luck!!

@Wfrench01

10 ай бұрын

@@boatdevoted jeg tror vi er i nesten samme land 😊 Jeg bruker annenhver glassfiber vev og glassfiber matte fra biltema. Gikk for kryssfiner istedenfor den du brukte.

@boatdevoted

10 ай бұрын

Aha, där ser man! Biltema har en hel del bra prylar men det finns andra leverantörer av polyester och matta med samma eller bättre varor eller priser. Jag har handlat av tex både chemify och dockyardscomposit. Kan rekommendera bägge!

hello, what resin do you use?

@boatdevoted

Жыл бұрын

Hi @yannnick13! I use GPX premium polyester laminating resin mainly. Sometimes also resin from Scott Bader.

@00:47 Why didn't you go till the edge of the bottom?🧐 It would have been stronger and make a nicer water flow. Now you get turbulence in two places...😳

@boatdevoted

Жыл бұрын

That’s the way Smuggler boats and Segmo boats are built, and they work great. My other boat is also an I/O conversion, with a similar bracket. It works amazingly well. Let’s cross our fingers and wait and see!

That is really the wrong wood to be using on a boat only got to get a stone chip cracked paint water gets in and Rot the wood that won't last long 5 years at most should have spent money on doing it right unless your selling it off

@boatdevoted

Жыл бұрын

Not sure what you’re referring to, since I’m not using wood anywhere.

@evanescecse

Жыл бұрын

Should’ve used marine ply not melamine chipboard but good effort though I’m thinking of doing the same 👍

@boatdevoted

Жыл бұрын

When just building simple molds its been less expensive for me using melamine chipboard.

@Ritebowl

10 ай бұрын

Are these guys serious? It’s his mold you idiots!!!!!!