PACKOUT and Die! Milwaukee PACKOUT Tap and Die Set with HEX-LOK Review [49-22-5603 -5604]
Тәжірибелік нұсқаулар және стиль
Mechanics, fabricators, contractors; many trades rely on a quality tap and die set. These new 38-piece Milwaukee PACKOUT Tap and Die Sets are available in Metric and SAE. The HEX-LOK system allows you to use the same tool for using the taps and dies. You also don't need any other tools, like a small screwdriver, for tightening set screws. Detents on the handle allow the dies to snap into place, and the same detents retain the tap holder in place as well. Look for these to hit the shelve in September 2023.
#milwaukeetool #review #packout
Milwaukee PACKOUT 38-pc Metric Tap and Die Set: acmetools.pxf.io/xkNqJd
Milwaukee PACKOUT 38-pc SAE Tap and Die Set: acmetools.pxf.io/Py6qzX
Keep current with our great content:
KZread: / shoptoolreviews
Instagram: / shoptoolreviews
TikTok: / shoptoolreviews
Facebook: / shoptoolreviews
Twitter: / shoptoolreviews
Пікірлер: 52
Every new accessory from Big M needs a PACKOUT case. Great review and demo TIM! You make it look easy!
@Shoptoolreviews
Жыл бұрын
Yes they do. Thank you very much.
I have used at least 10 tap pack out cases including the 2 that I own and this is by far the best well thought out tap case. About time they have the tap dies sideways in case to save room. Great tap wrench. If I have more then 1 or 2 holes to tap go to my starter tap or one of the dozen gun taps. In thin metal I will drill one hole size under. Hole drilled with a hand drill always cone out oversized due to slight wobble.
It would be cool if they made drills in a pack just for this tap and die set where the drill would have marked on it not the size of the drill itself but the tap you should use with that drill bit so you don't have to look at any charts or tables and then they can sell more drill bits
Very nice...worth $200...not a bad price for a good tap & die set...☝️
@Shoptoolreviews
Жыл бұрын
It is a nice set. Not the cheapest, but a decent price. Thanks for watching.
@jasonbrock293
Жыл бұрын
$200 each set =$400.00 🤔 not 200! Im not entirely convinced! For the price might as well buy off the truck
Wish they had a screwdriver for the taps for the tight spaces. That handle is better than the crap one I have
If you are going to make a chart for the little pack out area remember it only has to be metric on the metric and standard on the standard
I wonder if that hole on the back of the tap wrench/holder suitable for a tap follower? (yes, tap follower, not thread chaser)
They need a full size packout with both sae and metric all in one.
@pixels2polygonss
Жыл бұрын
I was just thinking the same thing!!! Great idea!!
What is your option of this vs the Gearwrench 114pc tap and die set?
Would those inserts drop into a full width packout low profile case? That way you can have one kit with both sizes in it?
tap and dies are nice.
@Shoptoolreviews
Жыл бұрын
Yes, they are, especially the handles and tool holders. Thanks for watching.
I would be a little worried about those small taps in that jaw system, seems like it is not holding a lot of the shaft so maybe easier to snap if not really careful
@Shoptoolreviews
Жыл бұрын
It has the same amount of clamping area as any other tap system. Thanks for watching.
Yep, wouldn't have cost them much for a laminated card with the associated drill bit sizes. For $200 they could have included the drill bits and a tiny bottle of cutting oil too.
@danlux4954
Жыл бұрын
The drill bits should be sae also, can’t always find # bits.
Can you buy replacement parts?
Hopefully they bring out a bigger size kit like up to 3/4 for me. Where are these made ?
@Shoptoolreviews
Жыл бұрын
They're made in China. Black oxide coated. We think the bigger sizes will come very soon. Thanks for watching.
Why they dont have this on homedepot?
Wish the kit went up to big sizes!
@Shoptoolreviews
Жыл бұрын
They'll probably expand in the future.
What caliper was that Please.
I would like a PDF
These don't say if they are carbon steel construction, HSS I'm sure they are not, but that is just standard in the industry? I'd assume carbon steel with black oxide coating?
@Shoptoolreviews
Жыл бұрын
They're black oxide coated. Thanks for watching.
Make a laminated card that just sits on the inside of the lid.
Awesome sets. Just wish they made these ratcheting handles like gearwrench does.
@LordPadriac
Ай бұрын
Those are a bad idea. I've seen people using them and wonder why they break so many. The inclination is to stop thinking about what you're doing and just go. Your muscle memory in using ratcheted tools takes over and you just go. The obvious problem being you're not back tracking to break chips and likely also not adding oil at the right times because you're on autopilot.
@FixitFred
Ай бұрын
@@LordPadriac I have had zero issues with my gearwrench ratchet taps. Quality taps and slow movement is all you need haven’t broke any taps and it gets me into tighter spots because I dont have to a 360 revolution to cut the taps. And spinning back to break chips is very easy
👍👍
Someone please give this man his hearing aids back.
It's gold because metric is the gold standard 😏
Going for broke!
Found the best tap fluid is the Tap magic from the 1980's. Guess the government made them change the formula but that stuff would evaporate cooling the tap. Worked in a 65 man maintenance shop where they always had a dozen cans of halve empty cans and boss would tell us to clean up shop every Friday so I would pour the halve empty cans into other tap magic cans and take them home. Even with the little red cap screwed on tight fluid in cans evaporated maybe 20% over the years.
When you cut the threads how tight is the nut and bolt when halfway assembled how much wobble is there??? And are they bottom out taps that thread to the bottom of the hole??? Cool is cool but sometimes not feasible...
It’s nice but not worth 200$ a set
@Shoptoolreviews
Жыл бұрын
It is a little pricey, but we love the Handle and Tap holder. Thanks for watching.
@WVCBUS08
Жыл бұрын
Especially when you can get the Gearwrench one that’s 114 pieces for < $250
what a waste of space
@Shoptoolreviews
Жыл бұрын
You can pull the inserts out and not use the PACKOUT case.
@nickgibb4687
Жыл бұрын
@@Shoptoolreviews i know, but its still a waste of space at the end of the day
@HardAss69
Жыл бұрын
@nickgibb4687 then don't buy it 🤔
@chuckandmariobuilt
Жыл бұрын
You’re out of your damn mind
@nickgibb4687
Жыл бұрын
@@HardAss69 dont worry i wont
danke gruß aus germany
@Shoptoolreviews
Жыл бұрын
Thanks for watching.