Great tutorial at the right speed.

Perfect walkthrough, went flawless, right now running the new calibration feature. Thanks a lot !

THANK YOU! All the other videos didn't go as in-depth and I had a little piece stuck inside. Ironing, NEVER AGAIN.

Thank you so, so much. The part to loosen the screw of the cutter was essential, I had the feeling I would force and break as-is. Other videos this part is suddenly moved aside to allow the gears to be removed but none tell you *how* you can move the cutter safely away. Huge thanks and props for this!

Like others have said, this is a fantastic video, instructions are clear and to the point. Thanks for making this available.

5:30 The video is missing a part: After putting on the silicone sock, remember to install the fan back on, with the 2 screws. The screw side is the same side the cables are. The fan is also oriented with the sticker side in, otherwise the cable will be too short to connect back at the printer

@TripasGarage

8 күн бұрын

@@rubberonasphalt you are correct. Thank you

This is a fantastic video. The swap when ALMOST perfectly. In my case, the screw holding the cutter arm was so tight, the supplied wrench started to strip the screw head. I found another allen wrench in my garage that worked great. I made sure to tighten it enough, but not TOO much when i reinstalled it. Thanks for making such a great tutorial!

This was EXCELLENT! install went super smooth following these directions.

Thanks for sharing your knowledge. Just added a Hardened Steel Extruder and Hotend to print CF and Glow-In-The-Dark filaments.

Great video, very clear, great instructions! Thank you!

Perfect tutorial. Thank you so much!

I did this on my P1S this evening. It really is this simple.

@AnomieDomine

9 ай бұрын

What parts did you order?

@blackbeard1984

3 ай бұрын

@@AnomieDomine Complete Hotend Assembly 0,4mm Hardened Steel and Hardened Steel Extruder Gear Assembly

Wow! Everything perfectly staged, a truly amazing video! Thank you very much for it!

@TripasGarage

Жыл бұрын

Appreciate it

Exceptional video! Thank you heaps for making this.

Thank you!!! Im about to do an extruder replacement and an upgrade install for the hardened gears. This is VERY helpful!

Perfect! Thank you so much!

Excellent video I've watched a few tear downs and yours is by far the most detialed and best filmed. Great work

@TripasGarage

7 ай бұрын

You’re very welcome and I appreciate it.

great tutorial - done my P1S today using your instructions. Bring on the carbon fibre!

Thanks! Everything went smoothly

Perfect!!

Really good video, thank you.

this video was very helpful, i enjoyed assembling the part with the help of this video. Thanks for showing us how to fix it

Absolute a great video, just followed the steps and it was super easy to do. Thanks for such a great instruction video.

You're a legend, thank you!

I was looking everywhere for a tutorial and finally stumbled upon this one. Thank you!

@TripasGarage

6 ай бұрын

You’re very welcome. I’m glad it came in handy

You’re the freaking man! Thank you! Even though I wish I would have just ordered the full hot end lol

Thanks for putting that together.

@TripasGarage

Жыл бұрын

You're very welcome

Thank you for this video.

Great and detailed instructions, thanks!!

@TripasGarage

Жыл бұрын

You're very welcome.

Epic video. I used it to fix a super jam I had with mine.

thank you and greetings from germany !!!

Very helpful! Thanx. Some Filament remains at the gear, so i need this instruction to reassemble the extruder! Success!

Its the best Video for Yutube , for extruder clog vice 1 pi 1 . THANKS , ❤❤❤❤❤❤❤❤

Great video. Thank you

@TripasGarage

Жыл бұрын

You’re welcome. Thank you for the feedback

Thanks for the info

Informative and interesting! 👍

@TripasGarage

Жыл бұрын

Thanks leaky! Appreciate it.

Nice video tutorial.

Great video.

Thanks for the nice explanation. Mission successful 😃👍

@TripasGarage

6 ай бұрын

You're very welcome. I'm glad it came in handy.

Highly recommend electronic swabs over the standard cotton ones. They don't shed like normal swabs so no stands of cotton mixed into the thermal compound.

@ipdjbt

11 ай бұрын

Medical grade swabs are cheaper and plentiful.

@eier81

10 ай бұрын

Yes, something other than Q tip. The bambulabs video says to use a Q tip, and I did, but it leaves behind some cotton strings of not careful, seems like not a good thing when the thing is getting so hot.

best toturial for this. needed to unclog my 3d printer and all the other videos skipped the disable part.

@TripasGarage

Ай бұрын

I got you! 👍🏼

Good luck putting those wires back ! 😢

Thank you so much for this 🤘🤘 I'm very happy that I bought the fully assembled Nozzle upgrade...!

@woodwaker1

7 ай бұрын

It is almost impossible to switch the thermistor without damage to the wire coating (at least for me)

Just followed your vid to make the swap on my P1S, all steps are identical from P1P. Thanks for posting this. Not sure if the gears are supposed to be lubed or kept dry. The wiki didn't seem to mention this either way, so I left dry for now.

Great video! Thanks!

@tripasgarage at 1:38 you are somewhat forcing the cutter lever too much, if you loosen the screw on the cutter a bit more, you will not need to force it. The screw has two positions, loosen a small amount and you can get the cutter out; loosen further and the arm will be able to move further out.

Hi, for printing wood filament, is the stainless stell nozzle and extruder gears that the P1S comes with, good enough?, or both nozzle and extruder gears needs to be replaced with the hardened steel ones?

1100 hours according to my unit.. Only have printed PLA.. I just had to replace these extruder gears. Sounded like it was popping while printing.

@TripasGarage

5 ай бұрын

oh wow! That’s good info to know that it’s not just needed for abrasive filaments. I’ll have to order me some more to have on hand here for maintenance. Thanks for the heads up.

@wolfsbane2802

3 ай бұрын

interesting I only print PLA, my extruder just starting to have issues at 1021 hours of print time lol. still using the default stainless steel gear on my p1s.

Thanks for the quick rundown. btw this does not work very well if you have a clog mid print, and you disassemble it on the fly, lol. Layering issues after restart. oh well it was worth a shot

0:33 во время обслуживания принтера нужно надевать перчатки из латекс, и при заправке филамент, чтобы не оставлять грязь и жир от рук. Все это имеет накопительный эффект. Хирург, же моет руки, перед тем как проводить операцию

@TripasGarage

2 ай бұрын

A surgeon is also working with sterile environments.

The white tube on my p1s is stuck on there, pushing on the black collar doesn't seem to release it.

Thank you for the detailed and smooth video! I have a P1S. Are these the same hotend and extruder gear I'd have to buy to upgrade the P1S to be able to print abrasive materials? Thanks in advance!

@woodwaker1

7 ай бұрын

They are

Recommendation is to not use cotton swab as it can leave fibers behind. And you missed 2 very important steps: 1. After replacing and reassembling, change the nozzle to hardened steel in the menu, in the printer configuration. 2. After updating configuration, run a full calibration test to make sure everything works fine and bed /nozzle distance is reset

@TripasGarage

3 ай бұрын

While I don’t disagree with you, a recalibration and the homing is a very important step, it just doesn’t have anything to do with physically changing and touching the hotend. It wasn’t missed. I appreciate your feedback. Maybe you can remix this video

Ty for the great vid ! That the x1 chain assembly on the p1p ? want to up grade mine like that .

@TripasGarage

Жыл бұрын

I appreciate the feedback and view. Yeah, this is the X1 cable chain. So far I've no issues with it. It's pretty cheap fix and once you buy the parts, you can reference this video for an easy step by step

@brandongardner2853

Жыл бұрын

@@TripasGarage Thank you so much will be making this upgrade soon .

@TripasGarage

Жыл бұрын

@@brandongardner2853 You're welcome. Shoot me a message or reply back here if you're having any issues or questions. You can also contact me on instangram messaging. Pretty quick there @tripasgarage (you'll see lots of cars) that's the page lol.

Does the x1. Arvin come with the hardened version?

@TripasGarage

Жыл бұрын

Yes

What are the calibration and tuning you have to do after installing these? Can you make a video about it.

@reddragonflyxx657

2 ай бұрын

I didn't see anything in the documentation, but ran the standard calibration process anyway. It worked fine immediately afterwards, so I didn't do anything further. I also changed the nozzle type in the Bambu Studio settings, but I think the only difference there is whether it warns you before you run a spool of abrasive filament through a stainless nozzle.

What was the part you had on your PTFE tube? Is that something I can print and put in place?

@TripasGarage

4 ай бұрын

Hi there, it’s only needed if you don’t use a riser. I typed ptfe tube guide p1p. It is something you can print.

Are you using the original bambu lab drag chain?

@TripasGarage

Жыл бұрын

That is correct. Using the chain from Bambu.

can not take the wheel out because a piece of filament stuck , any idea ? : )

@lmaoroflcopter

9 ай бұрын

Use a hotend screw as a drift on the back of the gear assembly to knock it out from the housing. Just a few gentle taps should knock it free.

I'm assuming this makes the printer able to cope with more abrasive filaments like carbon fibre?

@TripasGarage

3 ай бұрын

That is correct :)

Does this allow the hotend to get to 300 deg C

@TripasGarage

4 ай бұрын

It sure does just like the non hardened steel one. This one does allow you to use abrasive type filaments.

This upgrade allows to print harder abrasive materials?

@TripasGarage

Ай бұрын

Correct

Does this need to done for every nozzle change?

@TripasGarage

Жыл бұрын

Depends on what you buy.

@lmaoroflcopter

9 ай бұрын

You can buy the complete hot end assembly, then a nozzle change is two screws and a unplug/plug operation. Takes less than 30 seconds

Hello. Where do I get the white piece, where do I know it is at the entrance of the extruder? Thank you

@TripasGarage

4 ай бұрын

The heating element? It's from Bambu, it's what heats the hotend.

@CasaTridimensional

4 ай бұрын

@@TripasGarage I was asking about the moving piece that connects the hose where the filament enters.

@TripasGarage

4 ай бұрын

@@CasaTridimensional Oh! I downloaded an STL off printables. www.printables.com/model/350714-bambu-lab-ptfe-guide

@CasaTridimensional

4 ай бұрын

@@TripasGarage thanks amigo

Why is there a sticker over the hot end?? 1:09

@TripasGarage

Жыл бұрын

You’re totally right. Never thought anything of it. Im guessing they’re thinking it’s ok since it’s on the heatsink.

Very helpful video though strange that it’s tagged with “prusa”, “resinprinting”, and “ASA”.

@TripasGarage

3 ай бұрын

🥰🥰

Now it says “cutter malfunctioning” 😔

Just broke my thermister 😢

@TripasGarage

Ай бұрын

Time to buy a new one

@Humbledandelion

Ай бұрын

@@TripasGarage I bought i assembled nozzle. i was trying to replace the old one with one that was stainless steel. bought a hardened steel afterwards and it went ok. thanks for the video.

Seems like a lot.

@TripasGarage

Жыл бұрын

Of?

@supermanscott

Жыл бұрын

@TripasGarage work for an average person. My old printer I could just switch the nozzle with a wrench.

@lmaoroflcopter

9 ай бұрын

​@@supermanscottyou can switch the nozzle with an Allen key in 30 seconds. Bambu labs run an integrated nozzle and heat break. You can either replace just the nozzle and heat brake (as per this video) or just replace the entire hotend unit. Cost of parts is £9.99 for the fiddly replacement or £32.99 for a 30 second swap, pick your poison.

@supermanscott

9 ай бұрын

@@lmaoroflcopter thanks , I just replaced the whole hot end easier for me.

Who would have thought bambulab is scamming people with aluminum gears?

@easyefpv6609

6 ай бұрын

Tell me yyou didn't get a GED without telling me😂😂😂😂yall dumb

@donkeydiehard879

4 ай бұрын

The gears that mater aren't plastic.​@@Oucontryboy

@radish6691

3 ай бұрын

Uh, no one. The gears that ship with the P1 are stainless steel.

Isnt the Hot-End the exact same ? I mean its steeel and 0,4 mm ??

@TripasGarage

4 ай бұрын

It’s not the same. One is hardened steel and the other is stainless