Thank you for this video. This is literally the only video of this repair that I've been able to find for my car. Cheers

I watch a lot of KZread videos before I start a project. This by far is one of the best I have seen. Thanks

@YourCarGuyDR

5 жыл бұрын

Chuck Westerlund I am humbled by your kindness.

Great camera angles on such a tiny spot. Bravo to you sir.

Awesome video! Thanks for sharing and making my life so much easier on knowing what I'm getting into.

You bought me something new about my car. Thank you! Much appreciated. Keep up the great work.

only video I could find about this sensor for the 1.8T, thank you!

Fantastic job with the camera work. Thanks for sharing your knowledge

Thanks a lot for your generosity sharing this video with us !!!

When I went to order one from orileys they asked if it was oval or rectangular after saying I have an 01 passat 1.8t. I asked if there was an engine code specific and they said "no its one of those wonky things"🤣😭😭 but thanks another for this video kind sir.

Great video on this,that sensor can be a nightmare if the bolts to badly rusted

Thanks. I have this same vehicle offering the same p0322 code and I'm going out to play with it now. It's nice to know in advance what to expect and how to handle it.

1.8T: It’s really hard to get to on this engine. VR6: Hold my beer.

@Mstrofpup

4 жыл бұрын

lol. I

@JackJack-ne9cb

Жыл бұрын

1.8t awd Audi won’t be as simple huh

Hi thanks for your great video. My 2009 Rabbit had the EPC and check engine light on, so I changed to a new throttle body. But both lights were still on after 20 mins drive. So I found your video and bought an OBD2 scanner, found out the P0322 code. I changed to a brand new crankshaft position sensor, run the OBD 2 scanner again, the code P0322 is still on. I tested drive the car and seems ok. Can I still continue to drive without reset the code? Or it must to be reset if not the car will died again? Thanks in advance

Thnx m8 you saved my lif..... Uh car

Great video! I just did this on my Beetle 1.8T. Pain in the ass since you can't really get a good bead on it. The original lead is way too short and the bracket was a pain. I took out the funny thing that looks like a horn but goes to airbox. Took me 2.5 hours to change it out. I wish I saw this video. Anyway, just wanted to say great job!!

@YourCarGuyDR

4 жыл бұрын

customcruiserroy thank you I appreciate it.

I have the same issue with 2001 1.4 VW Polo. Ordered the new sensor and will be fitting it when it arrives. Exact same codes as yours.

@alanwong928

5 жыл бұрын

I used the VCDS HEXNET with my iPad to diagnose the fault. Its a good bit of kit to use.

Hey, thanks for the video. Unfortunately I cannot get my sensor out, I’ve taken out the 10mm mounting bolt but the sensor is extremely stuck, it spins freely but will not pull out from the mount despite many hours of prying and pulling. Any tips? I’ve been debating hitting it with some pb blaster but have not tried this yet. Thanks in advance

@YourCarGuyDR

5 жыл бұрын

Riley Lerner the pb blaster can be helpful. It’s a tight spot to work in but if you have some sort of small prybar you can work under it.

Saludos amigo buen video 👍

Great vid, exceptional even. Now get rid of that silly BOV and stop wasting gas.

Thank you for this

Thank you for this video, another question. I’m getting the codes u showed but also secondary air injection pump code. But I’ve cleaned wiring n put a new OE one and that code still comes up. Check valve? Help

@YourCarGuyDR

2 жыл бұрын

Which specific code are you getting for the air pump?

FYI this also applies to 2.0 ltr. The 10 mm bolt will also accept a 5 mm allen, but the space is likely to be full of dirt. 10 mm socket is the way to got.

@nolahahnshouse3389

3 жыл бұрын

Was just about to say this

@joelprovine7543

Жыл бұрын

2.0 tdi?

@gaborherman1481

Жыл бұрын

@@joelprovine7543 No, this is on Mk4, with 2.0 gas engine. I spent way too much time cleaning out the indentation on the bolt head for the 5 mm Allen. When I was done, I realized that a 10 mm socket would’ve been much more efficient and better use of my time. The instructions only mention the 5 mm Allen wrench and not the 10 mm bolt head. Good luck.

@vicecoldyt9763

Жыл бұрын

I also have the mk4 Jetta 2.0 thanks for your comment

Great video. What were the symptoms before you changed the sensor?? I was going down the highway doing 75+mph on 5th gear and the RPMs just dropped down to 0. Kinda scary when you are in traffic. Put it in 4th gear and I was able to rev it up and bring it back to speed. It wouldn't get past 4,000rpms after it though. Took it to autozone and got the same code. Did you have that problem also and did it get fixed after replacing the sensor?

@YourCarGuyDR

4 жыл бұрын

Alex Lara yes had the same issues and no problems since repair.

@alejolar90

4 жыл бұрын

@@YourCarGuyDR thanks for the response. One more question where did you get the replacement sensor from and would you recommend a Bosch replacement. Thanks in advance

@YourCarGuyDR

4 жыл бұрын

Alex Lara I always prefer Bosch when it is the OE supplier. I sourced it online via Amazon.

Exactly my symptoms and codes plus I get one more I've forgotten. P106 maybe. Anyway 2013 golf 2.5 motor ...let the investigations begin

How does the car react when it needs a new Crankshaft position sensor because i have a 05 jetta gli 1.8t automatic and it jerks hard when it goes from 1st all they way to 4th its fine on the hwy going like 70mph but when im in town it starts jerking please help for the love of god!!!!

@YourCarGuyDR

3 жыл бұрын

jacob baker that sounds more like a misfire to me. Are you getting a check engine light at all?

I have P0321 fault code after replace the sensor,does anyone know how to resolve the problem?? Btw is vw polo 1.9tdi 2009

I have a 1.8t 2003 Jetta. So the crankshaft sensor would also be located at same spot ?

@YourCarGuyDR

4 жыл бұрын

Light , yes

@light2011

4 жыл бұрын

Your Car Guy DR thank you I found the crankshaft sensor. also was wondering where is the camshaft sensor located as well

Great video appreciated ,i have a '03 vw golf..2l auto,engine light came on recently n upon diagnostic p0322/p0321 came up on inspection,first i thght wld be coil pack so i changed it ,bt car stil cuts off n thn starts bk up,upon viewing yr vdo i think i understand the problem,plse advise if this is the issue here,gladly looking forward for yr thoughts on this,ta.

@YourCarGuyDR

2 жыл бұрын

Yes this should be the issue with your golf.

@danielprakash6589

2 жыл бұрын

@@YourCarGuyDR ...Thanks for your prompt response,appreciated,hve a gd day team.

Does this cause the EPC light to come on? My car has all the same symptoms. But the epc like was on too

@YourCarGuyDR

5 жыл бұрын

Luis Zayas yes it does

@luiszayas03

5 жыл бұрын

@@YourCarGuyDR Thank you!

@PeterFeltersnatch852

3 жыл бұрын

@@YourCarGuyDR my car is showing these symptoms but not a check engine light will you 100% get a check engine light for this?

@YourCarGuyDR

3 жыл бұрын

Simple Man it is possible to have a bad sensor without the code.

Would you happen to know if the location is the same for a 2005 VW Jetta GLI 1.8T?

@YourCarGuyDR

2 жыл бұрын

It should be the same on all of that era 1.8t motors

Hello great video ,but i have a question i diagnosed my car the other day with a vcds and it showed me a error saying Knock Sensor . Thanks in advance

@YourCarGuyDR

3 жыл бұрын

If you have a knock sensor code I would inspect and or change the knock sensor first.

@todormitkow8622

3 жыл бұрын

@@YourCarGuyDR I changed it ,however the fault poped back up again with another one saying Internal Control Module ROM Error could that be causing the knock sensor to pop back up again even if changed ,thanks.

@YourCarGuyDR

3 жыл бұрын

@@todormitkow8622 yes. If the control module is having a ROM issue there is a chance that you need a new computer.

@todormitkow8622

3 жыл бұрын

@@YourCarGuyDR Thanks for the feedback.

Thanks heaps

I only have the p0321 code, not the other one. It's on my mk4 1.6 16v. Will it be the same issue? Please help someone

@YourCarGuyDR

3 жыл бұрын

Probably the same issue.

Replaced mine now misfire and backfires at anything above 4,000 rpm could that be a result of not clearing the codes after replacing?

@YourCarGuyDR

2 жыл бұрын

Most likely you have something else going on. Possible bad coils or timing chain issues.

Would be cool if I knew where your camera was so k could figure out where this sensor is.

Did you had to do this under the car or from above?!

@YourCarGuyDR

3 жыл бұрын

Jeroen De Groot from underneath

Do you need to disconnect the battery when you do this?

@YourCarGuyDR

5 жыл бұрын

Evan Sensenbrenner I would recommend it.

@Evan-nk6ht

5 жыл бұрын

@@YourCarGuyDR Thank you sir. going to do this soon.

@siggymartin

4 жыл бұрын

No - but it doesn’t hurt to disconnect the battery when working under the hood. Don’t want to short out anything.

Nice

I got the same code when I scanned it. Problem is that it will not start. The engine just turns over. Will this repair fix it?

@YourCarGuyDR

4 жыл бұрын

jimmy86gti with that code it will most likely fix it.

@jimmy86gti

4 жыл бұрын

Your Car Guy DR fingers crossed 🤞

@YourCarGuyDR

4 жыл бұрын

jimmy86gti let me know how it turns out.

@angeljavier5320

2 жыл бұрын

jimmy86gti my mk4 is doing the same It cranks but wont start. Same code, only that same code P0321 Did yours start after replacing the sensor or it was something else?

@Chris6R97

11 ай бұрын

Just delete the code

Great video mate, but unfortunately for me i changed this sensor, i also changed the cam shaft position sensor. But i am still getting the code come up for p0321 and p0322 😢😢

@monicasilva6851

6 ай бұрын

Boa noite eu tambem estou com esse problema tsnho tenho um seat ibiza 6j8 de 2010 1.2 a gasolina

This is BRILLIANT. Mine broke today

@YourCarGuyDR

5 жыл бұрын

Megahn Britz good luck with it.

@YourCarGuyDR

5 жыл бұрын

Megahn Britz good luck with it.

Before change that sensor start engine was possible?

@YourCarGuyDR

5 жыл бұрын

Jan Nowak it would start cold. But if the sensor has completely failed it will not start.

I have a 2001 Golf 2.0 gasoline engine. Process is exactly the same. Just FYI.

@YourCarGuyDR

3 жыл бұрын

Good to know. Thank you.

I have a problem my car won’t start but the lights and everything else works we changed the starter new battery the car did start once or Twice but will not start again

@YourCarGuyDR

4 жыл бұрын

Alan Ramos I am assuming that the starter is not turning? If so you could have an issue with you ignition switch or the security system immobilized.

@alanramos2864

4 жыл бұрын

Your Car Guy DR we got it 😀 it was Electrical power from the battery to the starter

Bro said "Lemme help 175k people with some simple instructions and great camera work"

Does these cause a epc light?

@YourCarGuyDR

4 жыл бұрын

I’m Gold sometimes

@zachvw5349

4 жыл бұрын

Your Car Guy DR chill on me

@cadeynpeppel1686

4 жыл бұрын

I have the epc light and this is the same code i have mk4 golf 2.0

Is this a manual transmission?

@YourCarGuyDR

3 жыл бұрын

Yes

I jus took mine apart and don’t see this sensor.

2005 Jetta ,2*0 gl

I still can’t get the clip undone with a flat head

@YourCarGuyDR

5 жыл бұрын

Ryan Hanlin the clip can be very frustrating. Take your time and it will come apart.

@ryanhanlin6576

5 жыл бұрын

Your Car Guy DR I have a 2.0 how do you unclip that clip

@ryanhanlin6576

5 жыл бұрын

Also how do I know if it’s a squeeze clip or do I use a flathead

@YourCarGuyDR

5 жыл бұрын

Ryan Hanlin there is a squeeze tab on the connector. The squeeze tab lifts a lever to unlock the connector. As there isn’t much room you can reach under the lever with a flat screwdriver from the side shown in the video.

I replaced cam sensor and crank sensor rpm still goes up and down at idle.

@YourCarGuyDR

Жыл бұрын

Check for a vacuum leak.

@clydedouchard

Жыл бұрын

@@YourCarGuyDR I'll look into it thankss

I changed mine , and I still have the code and my car still won’t start

@YourCarGuyDR

4 жыл бұрын

Sonny Spisak check your connections and the wires.

I just had my mk5 gti stall out with 321 code took a few trys to start back up now sounds like it's missing

@YourCarGuyDR

3 жыл бұрын

boosted mk5gti very likely the sensor.

Thank you so much

Replaced this and car still having same code and shut off problem even after erasing codes with obd2 reader

@Chris6R97

11 ай бұрын

You wires are the Problem

My problem is i replaced it and i still have the code

@YourCarGuyDR

5 жыл бұрын

douglasspriggs97 you will want to check your wiring and connections.

@ryanjacobs8371

2 жыл бұрын

Same. Went from stalling a mile from my house to permanent limp mode but drivable.