He means programming it as in "Tuning the ECU to your car", Great video man that you for showing an actual bypass not just pulling shit off the car am=nd moving it behind the dash. You actually got hundreds of people back on the road including me. I think my pats is on the way.
@johnd3224
4 жыл бұрын
it may not be computer at all. there is a pats ring at the key a ring that goes around it and connects under column that goes from there to a black box on top of fuse block under dash and then sends signal to computer and says ok let the car start he has the correct key with correct chip.with out all this working it will not start.the crown vic ecu bypasses all that for testing.if it doesn't start with mustang computer in it and does start with the crown vic ecu that means u have a p.a.t.s problem with one or all of the components more than likely not the computer
@Daaavewilliams Жыл бұрын
in the middle of a 4.6 2v swap in a foxbody, this might be some of the best, simple info ive found, i thought i needed a tuner, and all this other sorts of shit thank you sir!!!
@israeldavidson6643
9 ай бұрын
I’m currently doing this swap to my foxbody as well, did this work for you? I’m going with the Ron Francis wiring harness and wanted a run a stock ecu. I’ve been thinking I needed a tuner as well.
@Daaavewilliams
9 ай бұрын
@@israeldavidson6643 I used the original stock harness. If I had the money I would’ve sent Ron Francis or even better the Holley system. But I was able to make the original engine wiring system work with a flash tune and pats delete with a SCT BDX tuner.
@stevodaman24062 жыл бұрын
Saved my day, thank you for the video!!
@ryancox2636 Жыл бұрын
This help me sooooo much thanks for posting this video man not much information on this it works 👍 😀
@twportre88094 жыл бұрын
All of yall asking repetitive questions... YES YES YES YES YES YES IT WILL WORK! IF YOU HAVE A 04 AND PATS FUCKS UP... GET A 96-97 CROWN VIC ECU AND TUNE IT TO YOUR CAR! As you can see he has a v8! Don't ask if it will work for a Taurus. Common sense people.
@curtishunter58562 жыл бұрын
Simple and to the point,thanks
@759fish6 жыл бұрын
will this work on a 1999 ford f-150 ?
@billyw.87254 жыл бұрын
Do you know if this would work with the 96 ford taurus too? It's original ECM is an ml2-302/303
@alsxtn042 жыл бұрын
have a 98 stick shift im about to try this here in a bit i have a p1260 engine dissable have any advice both original keys were lost had one replaced theft light clears after 3 seconds as well, its been a head scratcher i pulled some diagnostics and it might be a short somewhere as well
@georgioocean76296 жыл бұрын
Absolutely, this is the best simple ,direct video, other videos are meaningless, unless you don't have the pat anti theft issues like we do. Have the car towed and have them isolated out of the computer or if you're able to hand over the computer and they can reformat it
@johnd3224
6 жыл бұрын
Georgio Wild well said my friend this will save u hundreds
@Modularmotorkings
3 жыл бұрын
@@johnd3224 i have a question here is my contact info 609 661 0808 ok so here’s my story I have a 98 mustang gt I went and bought a Diablo tuner my tuner couldn’t read my vin so I had a mustang guy try reading my pcm with his computer to do hp tuner but the pcm was locked with a Sct tune he told me to buy another computer so I did tried doing the parameter reset instructions and programming keys crank no start it said only one key programmed ,theft light stays on doesn’t go off. This is my daily so we tried putting old computer back in and what do u know it wouldn’t start, I pulled it up to the shop and it ran on both keys.
@kccarl25823 жыл бұрын
Best idea ive heard ever!!!
@cavdrkz24 Жыл бұрын
Is this for the 4.6 or the 5.0? Im having an issue with a no start and its looking more and more like a pats issue
@jcv8371 Жыл бұрын
Will the 97 crown vic ecu work with a 99 town car to get rid of the pats
@rossgeorge3able2 жыл бұрын
Freaking genius with the crown vic! Thanks for the video Steve
@cljerjr316 жыл бұрын
great vid, thanks
@GorillaTagGod1183 жыл бұрын
Thank you dude i just did this and it worked legit wtf bro you save my ass
@loganparrish2396
3 жыл бұрын
Did you just put the 96 ecu in your 96 gt and it starts and runs?
@Etiennevisvang4 жыл бұрын
now that is a pats problem well solved!
@az98z28 Жыл бұрын
I just tracked one down to try on my 97 GT.. . Will the gauges work?
@NINJUNK003 жыл бұрын
So all I have to do is buy a cv ML2-333 ecu and plug it in and it’ll work?
@aro52763 жыл бұрын
I have the p1260 right now, 98 mustang gt auto. What computer ecu do I need to get the car running again?
@ricardoolivares54762 жыл бұрын
So I got a 2000 mustang gt and I tried this I went to the junk yard got the 333 pcm model and it still doesn't work the theft light keeps blinking what do I do now
@johnd32246 жыл бұрын
as far as i know it will work and bypass it.pats is pats.but remember its for testing only.it will not turn on the fan.
@bigmikelongwood3276 Жыл бұрын
Hey man I'm tryin to do the same thing but in a 98 I got the same ecm out of the 96 crown Vic but still no start any ideas
@aaronjacobs22966 жыл бұрын
Thank you pal
@jimmymaupin47623 ай бұрын
Would it work for a 2004 3.8
@mustangdoctor38342 жыл бұрын
Will this work on my 97 Cobra?
@ever9183 жыл бұрын
As you did, I have the same problem, the anty theft turns on me, thanks
@MILO201214 жыл бұрын
Thx u for the vid
@johnd3224
4 жыл бұрын
hope it helped
@Dairiel_Vlogs11 ай бұрын
Would this work on a 01 GT?
@kristinculpepper62162 жыл бұрын
Hey I’m doing this exact thing to my 97 mustang idk how to find the new plug in I need to be able to install the crown Vic brain and where do I install it I need any info u can give me
@tristenoberlender96854 жыл бұрын
What will need to be programmed
@Lsxflakko5 ай бұрын
Okay so this is a bypass if you do realize it’s a pats issue how do you go about fixing it ?
@heroknaderi5 ай бұрын
Cool
@svtxj99212 жыл бұрын
So if I do this swap will the car run and drive? A car I’m looking at is having a PATS issue so if I swap the ECU will I be able to drive it home? Also will a handheld tuner work to reprogram it, like an SCT device? Or would it need to go to a custom dyno tuning shop?
@johnd3224
2 жыл бұрын
u would have to get it tuned this is only to see if u have a pats problem because it's from a crown vic the car will start but not cool or shift correctly.so if u live close it will get u home but be careful and watch gauges
@MikeJones-em8vz4 жыл бұрын
Has anyone done this and NOT reprogrammed or tuned the crown vic ECU and mustang drives fine? I know the ECU controls automatic shifting..but my concern is any other things if affects? I have a manual mustang 96
@juanbriones9582
2 жыл бұрын
I think because the car is a manual transmission the PCM might not work right
@thomasford80113 жыл бұрын
Got a completely different motor
@edwardtrauth42243 жыл бұрын
Can you take the lil black box key ring key and fob for a Ford explorer 4.7 and switch it out on a 2003 Ford expedition cause I grabbed all that at junk yard off a 2005 Ford explorer to see if I can get this expedition running???
@naomifuentes3517
3 жыл бұрын
Hi Edward, I had same problem and *Cyber_kor* on Instagram helped rectify mine. He is a great champ!. He is also on WhatsApp + 1 347 830 3644
@kellymayes16649 ай бұрын
Get a police interceptor crown vic ecu and its eet up missins for high performance like mustang so you will be in similar ballpark for settinga rather than normal family car non high performance ecu settings
@robjr3234 жыл бұрын
I got a ethos,tech snap-on reader thought
@johnd3224
4 жыл бұрын
good reader
@kellymayes16649 ай бұрын
POLICE INTERCEPTOR SET UP SIMILAR TO MUSTANG..BOTH HIGH PERFORMANCE LIKE SPORTY RACCE CAR TYPE EMISSIONMORE GAS TO FEED GEAR 2:20 SET UPS AND ALL THAT.
@slobmob63134 жыл бұрын
Got a 98 GT so I just get the computer and install it and it should start up or do I take out the model thing under the steering wheel too
@johnd3224
4 жыл бұрын
if u get the crown vic computer put it in if the car starts then all u have is a pats problem.dont leave crown vic computer in as it will not turn fans on correctly its only used to diagnose the pats problem at that point if u have a pats problem either have pats tuned out of the car or locate the bad module
@KevinLCann
3 жыл бұрын
Can I use a ml2-333A computer or does it have to be exact ml2-333?
@marklessard29875 жыл бұрын
My 1997 mustang has a problem the crown Vick’s and mustang have the same shut how would this work
@johnd3224
5 жыл бұрын
crown vic added pats in a later year thats why u can test with the vic computer.it doesnt recognize any of the pats modules
@Rbjx14 жыл бұрын
Now will the 97 ford mustang 3.8 v6 work with 97 crown vic ECU?
@johnd3224
4 жыл бұрын
its v8 going to v6 not sure but try and see
@josephkisiel2139
2 жыл бұрын
so did it work for your v6?
@boostedbrothers56062 жыл бұрын
If the ECU is for a auto will it work with a manual?? And any ECU shop can tune it?
@johnd3224
2 жыл бұрын
this is for testing to see if u have a pats problem.putvit this way if the car doesn't start do to pats and u swap the ecu and it starts u have a pats problem not an ecu problem
@jtmartin84452 ай бұрын
The ultimate fix is to send your pcm to someone who can delete that stupid shit out so you never have an issue with it.
@fatboybuilt5 жыл бұрын
I have a 98 Gt and swapped it to a ml2-333 ecu still no fire should I remove the pats module off also since it’s still in the car thanks ?
@johnd3224
5 жыл бұрын
it has to match pats module beside fuse box.heres a break down that might help. 1 chip in key sends signal to steering column collar 2. steering column sends signal to module by fuse box. 3 module sends signal to computer. if it all matchs the computer says ok start car. all the modules keys and computer have to match or be flashed to match or it wont work ever.
@johnd3224
5 жыл бұрын
also what was the computer number on the one u removed?
@georgioocean76296 жыл бұрын
You still got to reprogram the computer
@johnd3224
6 жыл бұрын
Georgio Wild you can only use this for testing..you cant run it or reprogram it because the crown vic computer wont turn fan on or shift car correctly
@johnd3224
4 жыл бұрын
it may not be computer at all. there is a pats ring at the key a ring that goes around it and connects under column that goes from there to a black box on top of fuse block under dash and then sends signal to computer and says ok let the car start he has the correct key with correct chip.with out all this working it will not start.the crown vic ecu bypasses all that for testing.if it doesn't start with mustang computer in it and does start with the crown vic ecu that means u have a p.a.t.s problem with one or all of the components more than likely not the computer
@aaronjacobs22966 жыл бұрын
Will it work on a 96 gt mustang with straight shift
@johnd3224
6 жыл бұрын
Aaron Jacobs yes it will
@thomasford80113 жыл бұрын
What about a 97 cobra what do I do then?
@naomifuentes3517
3 жыл бұрын
Hi Thomas, I had the same problem on my FORD , my aunt recommended *CYBER_KOR* on Instagram and got mine done. He is also on WhatsApp +1 347 830 3644.
@xavierdelgado10234 жыл бұрын
Will it work on a 99 mustang...what can i do for a 99 mustang any advice
@johnd3224
4 жыл бұрын
as long as its a v8 it should work.but again its only for testing
@kenseydavis13136 жыл бұрын
Can this be done with any vehicle to get around belt system with PCM and ecu
@loreleigoshorn6918
5 жыл бұрын
Will i work on 03 merc
@kristopherhasenbuhler53936 жыл бұрын
What about a 2001 Taurus?
@johnd3224
6 жыл бұрын
Kristopher Hasenbuhler not sure how that would work...
@davidmoore66244 жыл бұрын
What about stick shoft
@johnd3224
4 жыл бұрын
wont turn fan on
@lFezMeGusta4 жыл бұрын
so my alarm will not turn off on my 96 mustang so im going to do this, but how do i reprogram it after installing
@johnd3224
4 жыл бұрын
installing what ?
@lFezMeGusta
4 жыл бұрын
@@johnd3224 the crown vic ecu, my mustang is a 5 speed
@johnd3224
4 жыл бұрын
@@lFezMeGusta the only thing the crown vic ecu will do is eliminate everything else as why it isnt starting. its a pats work around dont drive car with that ecu.fans wont turn on and thats bad.put the cv ecu in if alarm is off and car starts u have a pats problem and everything else is ok.at that point u have a pats problem
@braden_n544 жыл бұрын
Do you know if this will work for a new edge car ? I have a 99 originally 3.8l car that is my winter beater with 300,000 miles on it ...headgasket is leaking so I'm putting a 4.6 2v in it when winter is over but just trying to find a cheap solution for bypassing pats as it is just a beater .
@johnd3224
4 жыл бұрын
u have to have the entire wire harness all the way to the fuel pump plus the computer and all the pats stuff from the donor car.
@davidreplogle1798 Жыл бұрын
😮
@codymcguire51964 жыл бұрын
What do you mean by marring the keys
@asdfghjkl9706
Жыл бұрын
You have to make the key code match the car with the key so they're "married"
@mistersniffer68385 ай бұрын
What good is that for my 3.8??? :(
@JS-hk3lv
3 ай бұрын
Same issue here . Looking into trying a Ford f150 with the 4.2 V6. It's basically a stroker 3.8
@carlitosducoing85073 жыл бұрын
Doest work on a 2000 5.0 explorer ??
@johnd3224
3 жыл бұрын
I'm not sure it won't hurt anything to try.just don't run it like that it's only to test car.if it starts and runs with the crown vic ecu that means p.a.t.s is ur problem somewhere in the pats chain.
@brandon20982 жыл бұрын
will it work with a 2002 mustang gt?
@danielm94437
Жыл бұрын
94-04 mustang works
@evermedina37685 жыл бұрын
Will it work on a 2000 ford mustang
@johnd3224
5 жыл бұрын
yes it will
@xavierdelgado1023
4 жыл бұрын
Will the crown vic pvm 333 work on a 99 mustang or a 2000 mustang..thx u
@italktoplanetsbaby Жыл бұрын
I gave up and junked my 2003. Ive had it with ford. Never fucking again.
@kwskater2235 жыл бұрын
Will it work for a 4.2 v6?
@johnd3224
5 жыл бұрын
not sure on v6
@josephkisiel2139
2 жыл бұрын
so did it work for your v6?
@slidewayskrew2 жыл бұрын
I need to bypass pats on a 02 mustang could this still work?
@johnd3224
2 жыл бұрын
for testing only I've done it on new edge yes
@slidewayskrew
2 жыл бұрын
@@johnd3224 so I can take the thing from a Vic without pats and put it on my car n that’ll work? I’m building a drift car and didn’t get a key with it
@johnd3224
2 жыл бұрын
@@slidewayskrew TESTING ONLY.it will not turn fan on correctly for cooling.u will melt ur car.this is only to test to see if u have a pats problem if ur car doesn't start with the pcm u have in it and it does start with the cv pcm then its a pats problem if it still doesn't start with cv pcm then it's something else.also if u want goto the junkyard find an 02 with a key. u need key lock,pats ring that's around it,pats module under the dash on top of fuse box it's black and the pcm behind front right side kick plate.and now u have new pats
@slidewayskrew
2 жыл бұрын
@@johnd3224 thank you sir. I can put my fans a switch I just really need it to run
@johnd3224
2 жыл бұрын
@@slidewayskrew why a mustang for drift?unless u put a ton of hp to it its a terrible drifter?
@nopowerlaboratory4 жыл бұрын
Will it work on 97 v6?
@johnd3224
4 жыл бұрын
not sure on v6 cars but worth a try
@miriamakisiel1323
2 жыл бұрын
so did it work for your v6?
@juanbriones95822 жыл бұрын
Will it work on the gt
@juanbriones9582
2 жыл бұрын
Mine is a 2003 manual
@johnd3224
2 жыл бұрын
yes
@juanbriones9582
2 жыл бұрын
@@johnd3224 I am probably going to buy a new transceiver by the ignition because it's like 40ish dollars but if that doesn't work I will try this
@robjr3234 жыл бұрын
Must tip my hat to the no bullshit straightforward vid
@bagginn4 күн бұрын
ML2-339 ( 97 crown Vic) worked, theft flashing and no start before, only crank
@johnd3224
4 күн бұрын
@@bagginn just remember it's only for testing don't drive it like that it's only to determine I'f u have a pats problem or a car problem
Пікірлер: 121
He means programming it as in "Tuning the ECU to your car", Great video man that you for showing an actual bypass not just pulling shit off the car am=nd moving it behind the dash. You actually got hundreds of people back on the road including me. I think my pats is on the way.
@johnd3224
4 жыл бұрын
it may not be computer at all. there is a pats ring at the key a ring that goes around it and connects under column that goes from there to a black box on top of fuse block under dash and then sends signal to computer and says ok let the car start he has the correct key with correct chip.with out all this working it will not start.the crown vic ecu bypasses all that for testing.if it doesn't start with mustang computer in it and does start with the crown vic ecu that means u have a p.a.t.s problem with one or all of the components more than likely not the computer
in the middle of a 4.6 2v swap in a foxbody, this might be some of the best, simple info ive found, i thought i needed a tuner, and all this other sorts of shit thank you sir!!!
@israeldavidson6643
9 ай бұрын
I’m currently doing this swap to my foxbody as well, did this work for you? I’m going with the Ron Francis wiring harness and wanted a run a stock ecu. I’ve been thinking I needed a tuner as well.
@Daaavewilliams
9 ай бұрын
@@israeldavidson6643 I used the original stock harness. If I had the money I would’ve sent Ron Francis or even better the Holley system. But I was able to make the original engine wiring system work with a flash tune and pats delete with a SCT BDX tuner.
Saved my day, thank you for the video!!
This help me sooooo much thanks for posting this video man not much information on this it works 👍 😀
All of yall asking repetitive questions... YES YES YES YES YES YES IT WILL WORK! IF YOU HAVE A 04 AND PATS FUCKS UP... GET A 96-97 CROWN VIC ECU AND TUNE IT TO YOUR CAR! As you can see he has a v8! Don't ask if it will work for a Taurus. Common sense people.
Simple and to the point,thanks
will this work on a 1999 ford f-150 ?
Do you know if this would work with the 96 ford taurus too? It's original ECM is an ml2-302/303
have a 98 stick shift im about to try this here in a bit i have a p1260 engine dissable have any advice both original keys were lost had one replaced theft light clears after 3 seconds as well, its been a head scratcher i pulled some diagnostics and it might be a short somewhere as well
Absolutely, this is the best simple ,direct video, other videos are meaningless, unless you don't have the pat anti theft issues like we do. Have the car towed and have them isolated out of the computer or if you're able to hand over the computer and they can reformat it
@johnd3224
6 жыл бұрын
Georgio Wild well said my friend this will save u hundreds
@Modularmotorkings
3 жыл бұрын
@@johnd3224 i have a question here is my contact info 609 661 0808 ok so here’s my story I have a 98 mustang gt I went and bought a Diablo tuner my tuner couldn’t read my vin so I had a mustang guy try reading my pcm with his computer to do hp tuner but the pcm was locked with a Sct tune he told me to buy another computer so I did tried doing the parameter reset instructions and programming keys crank no start it said only one key programmed ,theft light stays on doesn’t go off. This is my daily so we tried putting old computer back in and what do u know it wouldn’t start, I pulled it up to the shop and it ran on both keys.
Best idea ive heard ever!!!
Is this for the 4.6 or the 5.0? Im having an issue with a no start and its looking more and more like a pats issue
Will the 97 crown vic ecu work with a 99 town car to get rid of the pats
Freaking genius with the crown vic! Thanks for the video Steve
great vid, thanks
Thank you dude i just did this and it worked legit wtf bro you save my ass
@loganparrish2396
3 жыл бұрын
Did you just put the 96 ecu in your 96 gt and it starts and runs?
now that is a pats problem well solved!
I just tracked one down to try on my 97 GT.. . Will the gauges work?
So all I have to do is buy a cv ML2-333 ecu and plug it in and it’ll work?
I have the p1260 right now, 98 mustang gt auto. What computer ecu do I need to get the car running again?
So I got a 2000 mustang gt and I tried this I went to the junk yard got the 333 pcm model and it still doesn't work the theft light keeps blinking what do I do now
as far as i know it will work and bypass it.pats is pats.but remember its for testing only.it will not turn on the fan.
Hey man I'm tryin to do the same thing but in a 98 I got the same ecm out of the 96 crown Vic but still no start any ideas
Thank you pal
Would it work for a 2004 3.8
Will this work on my 97 Cobra?
As you did, I have the same problem, the anty theft turns on me, thanks
Thx u for the vid
@johnd3224
4 жыл бұрын
hope it helped
Would this work on a 01 GT?
Hey I’m doing this exact thing to my 97 mustang idk how to find the new plug in I need to be able to install the crown Vic brain and where do I install it I need any info u can give me
What will need to be programmed
Okay so this is a bypass if you do realize it’s a pats issue how do you go about fixing it ?
Cool
So if I do this swap will the car run and drive? A car I’m looking at is having a PATS issue so if I swap the ECU will I be able to drive it home? Also will a handheld tuner work to reprogram it, like an SCT device? Or would it need to go to a custom dyno tuning shop?
@johnd3224
2 жыл бұрын
u would have to get it tuned this is only to see if u have a pats problem because it's from a crown vic the car will start but not cool or shift correctly.so if u live close it will get u home but be careful and watch gauges
Has anyone done this and NOT reprogrammed or tuned the crown vic ECU and mustang drives fine? I know the ECU controls automatic shifting..but my concern is any other things if affects? I have a manual mustang 96
@juanbriones9582
2 жыл бұрын
I think because the car is a manual transmission the PCM might not work right
Got a completely different motor
Can you take the lil black box key ring key and fob for a Ford explorer 4.7 and switch it out on a 2003 Ford expedition cause I grabbed all that at junk yard off a 2005 Ford explorer to see if I can get this expedition running???
@naomifuentes3517
3 жыл бұрын
Hi Edward, I had same problem and *Cyber_kor* on Instagram helped rectify mine. He is a great champ!. He is also on WhatsApp + 1 347 830 3644
Get a police interceptor crown vic ecu and its eet up missins for high performance like mustang so you will be in similar ballpark for settinga rather than normal family car non high performance ecu settings
I got a ethos,tech snap-on reader thought
@johnd3224
4 жыл бұрын
good reader
POLICE INTERCEPTOR SET UP SIMILAR TO MUSTANG..BOTH HIGH PERFORMANCE LIKE SPORTY RACCE CAR TYPE EMISSIONMORE GAS TO FEED GEAR 2:20 SET UPS AND ALL THAT.
Got a 98 GT so I just get the computer and install it and it should start up or do I take out the model thing under the steering wheel too
@johnd3224
4 жыл бұрын
if u get the crown vic computer put it in if the car starts then all u have is a pats problem.dont leave crown vic computer in as it will not turn fans on correctly its only used to diagnose the pats problem at that point if u have a pats problem either have pats tuned out of the car or locate the bad module
@KevinLCann
3 жыл бұрын
Can I use a ml2-333A computer or does it have to be exact ml2-333?
My 1997 mustang has a problem the crown Vick’s and mustang have the same shut how would this work
@johnd3224
5 жыл бұрын
crown vic added pats in a later year thats why u can test with the vic computer.it doesnt recognize any of the pats modules
Now will the 97 ford mustang 3.8 v6 work with 97 crown vic ECU?
@johnd3224
4 жыл бұрын
its v8 going to v6 not sure but try and see
@josephkisiel2139
2 жыл бұрын
so did it work for your v6?
If the ECU is for a auto will it work with a manual?? And any ECU shop can tune it?
@johnd3224
2 жыл бұрын
this is for testing to see if u have a pats problem.putvit this way if the car doesn't start do to pats and u swap the ecu and it starts u have a pats problem not an ecu problem
The ultimate fix is to send your pcm to someone who can delete that stupid shit out so you never have an issue with it.
I have a 98 Gt and swapped it to a ml2-333 ecu still no fire should I remove the pats module off also since it’s still in the car thanks ?
@johnd3224
5 жыл бұрын
it has to match pats module beside fuse box.heres a break down that might help. 1 chip in key sends signal to steering column collar 2. steering column sends signal to module by fuse box. 3 module sends signal to computer. if it all matchs the computer says ok start car. all the modules keys and computer have to match or be flashed to match or it wont work ever.
@johnd3224
5 жыл бұрын
also what was the computer number on the one u removed?
You still got to reprogram the computer
@johnd3224
6 жыл бұрын
Georgio Wild you can only use this for testing..you cant run it or reprogram it because the crown vic computer wont turn fan on or shift car correctly
@johnd3224
4 жыл бұрын
it may not be computer at all. there is a pats ring at the key a ring that goes around it and connects under column that goes from there to a black box on top of fuse block under dash and then sends signal to computer and says ok let the car start he has the correct key with correct chip.with out all this working it will not start.the crown vic ecu bypasses all that for testing.if it doesn't start with mustang computer in it and does start with the crown vic ecu that means u have a p.a.t.s problem with one or all of the components more than likely not the computer
Will it work on a 96 gt mustang with straight shift
@johnd3224
6 жыл бұрын
Aaron Jacobs yes it will
What about a 97 cobra what do I do then?
@naomifuentes3517
3 жыл бұрын
Hi Thomas, I had the same problem on my FORD , my aunt recommended *CYBER_KOR* on Instagram and got mine done. He is also on WhatsApp +1 347 830 3644.
Will it work on a 99 mustang...what can i do for a 99 mustang any advice
@johnd3224
4 жыл бұрын
as long as its a v8 it should work.but again its only for testing
Can this be done with any vehicle to get around belt system with PCM and ecu
@loreleigoshorn6918
5 жыл бұрын
Will i work on 03 merc
What about a 2001 Taurus?
@johnd3224
6 жыл бұрын
Kristopher Hasenbuhler not sure how that would work...
What about stick shoft
@johnd3224
4 жыл бұрын
wont turn fan on
so my alarm will not turn off on my 96 mustang so im going to do this, but how do i reprogram it after installing
@johnd3224
4 жыл бұрын
installing what ?
@lFezMeGusta
4 жыл бұрын
@@johnd3224 the crown vic ecu, my mustang is a 5 speed
@johnd3224
4 жыл бұрын
@@lFezMeGusta the only thing the crown vic ecu will do is eliminate everything else as why it isnt starting. its a pats work around dont drive car with that ecu.fans wont turn on and thats bad.put the cv ecu in if alarm is off and car starts u have a pats problem and everything else is ok.at that point u have a pats problem
Do you know if this will work for a new edge car ? I have a 99 originally 3.8l car that is my winter beater with 300,000 miles on it ...headgasket is leaking so I'm putting a 4.6 2v in it when winter is over but just trying to find a cheap solution for bypassing pats as it is just a beater .
@johnd3224
4 жыл бұрын
u have to have the entire wire harness all the way to the fuel pump plus the computer and all the pats stuff from the donor car.
😮
What do you mean by marring the keys
@asdfghjkl9706
Жыл бұрын
You have to make the key code match the car with the key so they're "married"
What good is that for my 3.8??? :(
@JS-hk3lv
3 ай бұрын
Same issue here . Looking into trying a Ford f150 with the 4.2 V6. It's basically a stroker 3.8
Doest work on a 2000 5.0 explorer ??
@johnd3224
3 жыл бұрын
I'm not sure it won't hurt anything to try.just don't run it like that it's only to test car.if it starts and runs with the crown vic ecu that means p.a.t.s is ur problem somewhere in the pats chain.
will it work with a 2002 mustang gt?
@danielm94437
Жыл бұрын
94-04 mustang works
Will it work on a 2000 ford mustang
@johnd3224
5 жыл бұрын
yes it will
@xavierdelgado1023
4 жыл бұрын
Will the crown vic pvm 333 work on a 99 mustang or a 2000 mustang..thx u
I gave up and junked my 2003. Ive had it with ford. Never fucking again.
Will it work for a 4.2 v6?
@johnd3224
5 жыл бұрын
not sure on v6
@josephkisiel2139
2 жыл бұрын
so did it work for your v6?
I need to bypass pats on a 02 mustang could this still work?
@johnd3224
2 жыл бұрын
for testing only I've done it on new edge yes
@slidewayskrew
2 жыл бұрын
@@johnd3224 so I can take the thing from a Vic without pats and put it on my car n that’ll work? I’m building a drift car and didn’t get a key with it
@johnd3224
2 жыл бұрын
@@slidewayskrew TESTING ONLY.it will not turn fan on correctly for cooling.u will melt ur car.this is only to test to see if u have a pats problem if ur car doesn't start with the pcm u have in it and it does start with the cv pcm then its a pats problem if it still doesn't start with cv pcm then it's something else.also if u want goto the junkyard find an 02 with a key. u need key lock,pats ring that's around it,pats module under the dash on top of fuse box it's black and the pcm behind front right side kick plate.and now u have new pats
@slidewayskrew
2 жыл бұрын
@@johnd3224 thank you sir. I can put my fans a switch I just really need it to run
@johnd3224
2 жыл бұрын
@@slidewayskrew why a mustang for drift?unless u put a ton of hp to it its a terrible drifter?
Will it work on 97 v6?
@johnd3224
4 жыл бұрын
not sure on v6 cars but worth a try
@miriamakisiel1323
2 жыл бұрын
so did it work for your v6?
Will it work on the gt
@juanbriones9582
2 жыл бұрын
Mine is a 2003 manual
@johnd3224
2 жыл бұрын
yes
@juanbriones9582
2 жыл бұрын
@@johnd3224 I am probably going to buy a new transceiver by the ignition because it's like 40ish dollars but if that doesn't work I will try this
Must tip my hat to the no bullshit straightforward vid
ML2-339 ( 97 crown Vic) worked, theft flashing and no start before, only crank
@johnd3224
4 күн бұрын
@@bagginn just remember it's only for testing don't drive it like that it's only to determine I'f u have a pats problem or a car problem